Goldmedal Karmel King 2620 User manual

Part No. 18736
Revised: February 2009
KARMEL KING
Instruction Manual
Models: 2620 & 2621 (240 Volt)
2630 & 2631 (208 Volt)

SAFETY PRECAUTIONS

___________________________________ KARMEL KING
MODEL # 2620,2621,2630, AND 26313
Mark 10, Karmel King (20 Gallon), and 2622 Rolling Truck
Left Hand Mark 10 (2411E) or Karmel King (2621) on 2622 truck shown
Electrical Specifications:
Mark 10 (2410E - RH, 2411E - LH) - 120/208v or 120/230v 4 wire (2 hot, 1 neutral, 1 ground) 60
Hz.
5520 watts 30 amp plug & receptacle ( NEMA L14-30P & L14-30R )
Karmel King/Models: 2620 RH, 2621 LH – 240v (2 hot, 1 ground) 50/60Hz.
7100 watts 50 amp plug & receptacle 50 amp plug ( NEMA 6-50P & 6-50R )
Karmel King/ Models: 2630 RH, 2631 LH – 208v (2 hot, 1 ground) 50/60Hz.
6760 watts 50 amp plug & receptacle 50 amp plug ( NEMA 6-50P & 6-50R )
Other Dimensions:
As shown.
40´x 60” Cooling Pan should be located approximately 3-5” below the Corn Treat Mixer Base
Model 2622 (Rolling Table)
Includes Casters
Includes (1) cooling pan ( order p/n 48845 for extra cooling pan)
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
Phone: [phone] fax: [phone]
e-mail: www.gmpopcorn.com 9/05

___________________________________ KARMEL KING
MODEL # 2620,2621,2630, AND 26314
INSTALLATION
CHECKING SHIPMENT
Unpack the shipping crate and check thoroughly for any damage which may have occurred in
transit. Any claims should be filed immediately with the transportation company.
ELECTRICAL REQUIREMENTS
Voltage for the 2620 AND 2621 is 240 volt, 3-WIRE ( 2 HOT, 1 GROUND) 60 cycle single phase. A wall
receptacle is supplied with the machine. This receptacle will accept the attachment plug on your machine
and must be used. The machine will draw a maximum of 30amps. Your electrician must finish sufficient
current for the proper operation of your machine. We recommend that this machine be fused on a line by
itself.
Voltage for the 2630 AND 2631 is 208 volt, 3-WIRE ( 2 HOT, 1 GROUND) 60 cycle single phase. A wall
receptacle is supplied with the machine. This receptacle will accept the attachment plug on your machine
and must be used. The machine will draw a maximum of 30amps. Your electrician must finish sufficient
current for the proper operation of your machine. We recommend that this machine be fused on a line by
itself.
COUNTER MOUNTING REQUIREMENTS/INSTRUCTIONS

___________________________________ KARMEL KING
MODEL # 2620,2621,2630, AND 26315
CONTROLS AND THEIR FUNCTION
HEAT SWITCH
This rocker switch in the “ON” position energizes the heating elements in the bottom of the kettle.
MOTOR SWITCH
With this rocker switch in the “ON” position, the agitator motor will run continuously.
HEAT CONTROL
The machine comes from the factory preset at 280°F. If more or less heat is required, remove the silver hole
plug or cover plate located on the front panel of the control box. This will allow you to access the heat
control adjustment potentiometer. Turn the potentiometer clockwise to increase the temperature, and
counter-clockwise to decrease.
To calibrate the heat control for corn treat, Fill the mixing bowl with a one inch depth of corn oil. Use an
accurate thermometer to measure the temperature of the oil in the mixing bowl. Turn the motor on to stir the
oil while it heats. When the oil reaches 280F slowly turn the potentiometer counter clockwise until the
buzzer sounds. If the buzzer sounds before the temperature reaches 280F, slowly turn the potentiometer
clockwise until the buzzer stops and continue to turn an additional 1/8 of turn.
Note: The sound of the buzzer always signals temperature cut-off.
CARE AND CLEANING
STEAM CLEANING
The easiest way to clean the kettle is to pour 8 ounces of water into the kettle while it is still hot. Place the
lid back on the kettle. Let it steam for approximately ten minutes. Remove the lid and dump out the water.
You will probably have to steam the kettle twice to remove all traces of product. Releasing the draw latch
makes the mixing drum easy to remove for cleaning. The mixing drum can be taken to the sink to clean.
The cabinet of your machine should be wiped cleaned daily; or more, depending on your usage.

___________________________________ KARMEL KING
MODEL # 2620,2621,2630, AND 26316
NEW PADDLE & HUB SEAL KIT INSTALLATION
1. Unscrew the wing bolts and remove both mix paddles.
2. Remove the old hub seal assembly.
3. Clean the area around the center hub. Clean up all food and carbon residue.
4. Remove any burrs on the top edge of the center hub. Use a fine grit emery paper to lightly sand the
surface. If the burrs are not removed, damage may occur to the hub assembly during installation.
5. Lightly lubricate the center hub of the kettle with a small amount of vegetable oil to allow for easy
installation of the hub seal assembly.
6. Slide the hub seal assembly down the agitator shaft. Apply pressure to ease the assembly over the
center hub of the kettle until it seats properly. (See diagram below.)
7. After the hub seal assembly has been properly installed, place the new mix paddle on the bottom and
one existing paddle on the top of the agitator shaft.
8. Replace the wing bolts and finger tighten.

___________________________________ KARMEL KING
MODEL # 2620,2621,2630, AND 26317
MAINTENANCE INSTRUCTIONS

___________________________________ KARMEL KING
MODEL # 2620,2621,2630, AND 26318
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include your model name, serial number, and date of manufacture (located on the machine
nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
[phone]
Fax: [phone]
E-mail: [email protected]
Web Page: www.gmpopcorn.com

___________________________________ KARMEL KING
MODEL # 2620,2621,2630, AND 26319
INSTRUCTIONS FOR MAKING CARAMEL CORN
1. Turn the heat switch "ON".
2. Add 24-28 ounces of water, (4) 22 oz. packages of Gold Medal Caramel Corn Mix, and (16) cups of
granulated sugar.
NOTE: When using the Gold Medal "One Step" Caramel Corn Mix, do NOT add granulated sugar.
3. Turn the motor switch "ON" and mix for approximately one minute. Turn the motor switch "OFF". The
motor will continue to cycle with the motor switch off. (With the heat switch "ON" the motor will run for 30
seconds every minute.)
4. Add four (16) ounce of sticks coconut oil or vegetable oil.
5. Allow the mix to cook until the buzzer sounds at 280° F product temperature.
6. Turn the heat switch "OFF".
7. Turn the motor switch "ON".
8. Add twenty gallons of pre popped corn.
9. Allow the corn to mix for approximately thirty (30) seconds with the kettle in the upright position.
10. Move the kettle to the mix position and mix the popcorn until it is thoroughly coated.
11. Dump the caramel corn into the cooling pan.

___________________________________ KARMEL KING
MODEL # 2620,2621,2630, AND 263110
PARTS LIST
2620 2621 2630 2631
Part No Part No Part No Part No Description
46488 46488 46488 46488 Tilt Lever
48882 48882 LH Dump Bar Assy.
48842 48842 RH Dump Bar Assy.
74660 74660 74660 74660 Torsion Spring
74661 74661 74661 74661 Collar
48839 48839 48839 48839 Hub-For Tilt Lever
48826 48826 48826 48826 Drive Coupling
46152 46152 46152 46152 Kettle Rest
48811 48811 48811 48811 Mixing Paddle
48819 48819 48819 48819 Mixing Drum
89810 89810 89810 89810 Lead In Cord
48814 48814 LH Control Box Weldment
48813 48813 RH Control Box Weldment
48816 48816 48816 48816 Pedestal Welded Assy.
42006 42006 42006 42006 Terminal Block
42798 42798 42798 42798 Switch, Lighted Rocker
89858 89858 Relay - 240 Volt, DPDT
46120 46120 46120 46120 Buzzer Signal
48301 48301 48301 48301 Capacitor Strap
48880 48880 48880 48880 Kettle Drive Motor
46498 46498 Heat Element 2700W
48650EX 48650EX Heat Element 1800W
48887 48887 Heat Element 2100W
69863 69863 Heat Element 1800W
69864 69864 Heat Element 2700W
69865 69865 Heat Element 2100W
48818 48818 48818 48818 Motor Mount
48825 48825 48825 48825 Agitator Shaft
48809 48809 48809 48809 Kettle
48817 48817 48817 48817 Bottom Cover Plate
68010 68010 68010 68010 RTD Heat Sensor
82219 82219 82219 82219 Thermostat Kettle L-510
48812 48812 48812 48812 Kettle Mount Bracket Casting
46326 46326 46326 46326 500 ohm Potentiometer
48688EX 48688EX 48688EX 48688EX Percentage Timer
55057 55057 55057 55057 RTD Temperature Control
62059EX 62059EX Contactor - 2 Pole, 40 Amp
46646 46646 46646 46646 Hub Seal Assy.