Goldmedal 1617 User manual

16 Oz. Pop
& Self-Serve Warmer
PopcornMachineInstructionManual
Model #1617
Part No. 16225
Revised February 1997
Cincinnati, OH 45241-4807 USA

SAFETY PRECAUTIONS
NOTE
The information, specifications and illustrations contained in this manual represent
the latest data available at time of publication. Right is reserved to make changes as
required at the discretion of Gold Medal Products Company without notice.
Any alterations to this equipment will void the warranty and
may cause a dangerous situation. NEVER make alterations
to the equipment.
Make sure all machine switches are in the OFF position
before plugging the equipment into a receptacle.
Always wear safety glasses when servicing this equipment.
Machine must be properly grounded to prevent electrical shock
to personnel.
Do NOT immerse the kettle, warmer, or any other part of this
equipment in water.
Always unplug the equipment before cleaning or servicing.
This equipment is designed and sold for commercial use only. This
equipment is not to be used by the consumer in home use. Do not allow
direct contact of this equipment by the public when used in food service
locations. Only personnel trained and experienced in the equipment
operation may operate this equipment.
Carefully read all installation instructions before operating the equipment.
To avoid serious burns, do NOT touch the kettle while it is hot.

16 Oz. Pop & Self-Serve Warmer
MODEL #1617
1
INTRODUCTION
Yournew#1617Pop&Self-ServeWarmer is shipped completely assembled, ready to operate. After
removingthecorrugatedcartonfromthemachine,checkthoroughlyforanydamagewhichmayhave
occurredintransit.Claimsshouldbefiledimmediatelywiththetransportationcompany.
Remove all cardboard packing and tape from the machine. Wipe all exposed surfaces with a damp
clothtoremovefingerprints,smears,etc.whichmayhaveoccurredduringunpackingandhandling.
ELECTRICAL REQUIREMENTS
Standard voltage for the Pop & Self-Serve Warmer is 120V, 60 cycle, single phase, A.C. current. The
unit should be placed on its own 30 Amp (4 wire) electrical circuit. The switches to control the
heaters, kettle and lights are located at the top on the inside of the cabinet.
CONTROLS
The switches control:
LIGHTS
Turns on internal lights and dome sign.
WARMER
Turns on corn pan heaters.
KETTLE MOTOR SWITCH
Turns on motor which drives kettle agitator shaft.
KETTLEHEAT SWITCH
Turns on kettle heat elements.
OIL SYSTEM MASTER
Turns the oil bucket pump heater on.
OIL PUMP
Dispenses oil into the kettle.
AMOUNT OF POPCORN AND OIL CHARGE
Your new popper is equipped with a 16 ounce corn measure cup. We recommend flavored and
colored coconut oil. Popcorn popped in coconut oil stays fresher longer. Coconut oil does not leave
the black deposits in your kettle like other oils.
Corn Charge - 16 Ounces
Oil Charge - 4 Ounces
Flavacol- 4 Tablespoons

16 Oz. Pop & Self-Serve Warmer
MODEL #1617
2
POPPING INSTRUCTIONS
1. Turn kettle heat and kettle motor switch on.
2. Make test pop with 3 kernels of corn and 1 ounce of oil.
3. Load corn, oil bar, and seasoning into kettle.
4. When corn has popped dump kettle.
5. Repeat steps 3 and 4 for additional batches.
Always pop three to five batches for best results.
CARE AND CLEANING
The aluminum frame of the popcorn machine is easy to keep clean. Usually a damp cloth will remove
alldirtandgreasespots.NEVERUSEABRASIVESonthealuminumframework.Theglass should
always be clean and sparkling. Remember the inside of the glass must be cleaned too. Empty the old
maid drawer and wipe clean. Remove bottom cabinet pans and clean out any stray debris.

16 Oz. Pop & Self-Serve Warmer
MODEL #1617
3
ORDERING SPARE PARTS
1.Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2.When ordering, please include part number, part name, and quantity desired.
3.Pleaseincludeyour model name and machine serial number (located on the machine
nameplate)with your order.
4.Addressallpartsordersto: Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail:[email protected]
NOTE:We donot ship glass. Obtain replacement glass from your local glass shop or
hardware store. Always purchase double strength type glass. Sizes are:
FRONTGLASS 32 3/16" x 15 11/16" x 1/8"
SLIDING DOOR GLASS 24 15/16" x 13 7/16" x 3/16"
MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN-
TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO
ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE
NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this
equipment to prevent the possibility of injury.
Do NOT immerse the kettle, warmer, or any other part of this
equipment in water.
Unplug your machine before servicing.

16 Oz. Pop & Self-Serve Warmer
MODEL #1617
4
CABINET ASSEMBLY

16 Oz. Pop & Self-Serve Warmer
MODEL #1617
5
PARTS LIST - CABINET ASSEMBLY
Item No. Part No. Description Quantity
1 16060 CabinetAssembly,#1617 1
2 16001 TopFrame 1
3 16064 BottomFrame 1
4 16062 Divider Panel 1
5 16038 Drop Panel, R.H. 1
6 16055 Wire Shelf 3
7 16065 Corn Pan, R.H. 1
8 16066 Corn Pan, L.H. 1
9 16139 Magnetic Catch Bracket 1
10 41879 CornerCover 2
11 47364 CircuitBreaker, 15A 1
12 41284 Old Maid Pan 1
13 47208 TerminalBlock 1
14 41013 DoorKnob 2
15 41349 Door Male Hinge, R.H. 2
16 41350 Door Male Hinge, L.H. 2
17 41351 DoorFemale Hinge, R.H. 2
18 41352 DoorFemale Hinge, L.H. 2
19 16090/16091 Corner Post, Front 1/1
20 41872 Corner Post, Right Rear 1
21 40192 Corner Post, Left Rear 1
22 47282 Bushing,Snap 4
23 47237 Door Striker 2
24 41282 Rubber Foot 4
25 16071 Front Glass 1
26 41190 SideGlass 2
27 41283 BottomCover 1
28 41766 GlassRetainer, Rear 2
29 41765 GlassRetainer, Front 2
30 16076 DoorAssembly 1
31 41858 RigidChannel, 32" 2
32 47694 Rigid Channel, 22 7/8"2
33 41860 RigidChannel, 26" 2
34 16050 Lead-InCord 1
35 16074 Divider Rail, Top 1
36 49480 Light Shield 2
37 41712 MoldedReceptacle 1
38 16059 CompleteHangerAssembly 1
39 41671 Reflector,FloodLight 2
40 16058 Motor Mount Plate 1
41 16141 MagneticCatch 1
42 41526 DomeSpacer 2
43 16056 Shelf Support, L.H. 2
44 16057 Shelf Support, R.H. 2
45 49480 LightShield, Conical 2

16 Oz. Pop & Self-Serve Warmer
MODEL #1617
6
PARTS LIST - CABINET ASSEMBLY (continued)
Item No. Part No. Description Quantity
46 47356 MotorWarmer,115V 2
47 47059 SpurGear 1
48 47065 GearBox 1
49 67179 Switch, Oil 1
50 42798 Swich,Motor/Light 5
51 47282 Bushing,Snap 1
52 47263 HangerArm,Rear 1
53 47262 HangerArm,Front 1
54 48492 SwitchBox 1
55 49116 SwitchLabel 1
56 49330 Receptacle,15 Amp, Twist-Loc 1
57 n/a n/a
58 16048 BottomDivider Rail 1
59 n/a n/a
60 41325 ReceptacleAssembly 1
61 41015 ExhaustBlower 1
62 41006 BlowerBoxAssembly 1
63 16052 SwitchLabel 1
64 41250 GreaseFilter 1
65 16075 Skirt(Optional Accessory, 1
Standard on Model #1617TS)
DOMEASSEMBLY
68 16061 DomeAssembly, Complete 1
69 16030 MainWrapper 1
70 16073 InspectionPlate 1
71 61085 Neon Lower Case Script 1
72 n/a n/a
73 n/a n/a
74 n/a n/a
75 n/a n/a
76 16069 FrontWrapperAssembly 1
77 47242/47243 Support Angle 1
78 47726 Molded Plug 1
79 47244 Neon Sign, Block Letters 1

16 Oz. Pop & Self-Serve Warmer
MODEL #1617
7
KETTLE ASSEMBLY

16 Oz. Pop & Self-Serve Warmer
MODEL #1617
8
PARTS LIST - KETTLE ASSEMBLY
Item No. Part No. Description
1 47107 C-Ring
2 47106 NeedleBearing
3 47059 SpurGear
4 41742 Set Screw, #10-32
5 47326 SetCollar
6 47751 Set Screw, ¼-20
7 41239 Oil Tube w/ Funnel
8 47691 Thumb Screw
9 47154 WarningPlate
10 47774 Rivet
11 41144 CrossbarAssembly
12 41120 RearLid
13 SeeDumpKettle Below FrontKettle Lid Assembly
14 47120 Lid Lift Knob
15 74141 Screw, #8-32 x3/8"
16 74150 Washer, #8
17 41093 AgitatorShaftAssembly
18 41069 KettleAssemblyPlated
19 41127 Heat Transfer Plate
20 82219 Thermostat,L510
21 41435 RetainingNut
22 41155 Heat Element, 500W
23 41183 HeatElement, 1250W
24 41878 ElementRetainer
25 76079 Washer, ¼-20Int.
26 74133 Nut,¼-20 Hex
27 SeeDumpKettle Below ShellAssembly, 16Oz.
28 74133 Nut,¼-20 Hex
29 47325 SetCollar
30 47662 Set Screw, 5/16-18
31 47707 DumpHandle Shaft
32 47110 Knob
33 46241 Connector,90°
34 82107-24 Conduit
35 82135 ConduitBushing
36 47951 Plug
37 41245 ThermostatHold Down
38 41318 KettleLeadAssembly
39 49350 ConduitCaution Label
DUMPKETTLE
40 2223 16 Oz. Steel Kettle Complete
41 41066 Agitator/LidAssemby
42 41130 Front Kettle Lid
43 41326 16 Oz.Steel Kettle Bottom
44 41081 ShellAssembly, 16Oz.