Goldmedal 2552-00-001 User manual

© 2017 Gold Medal Products Co. Part No. 110131
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
PopMaxx with Lighted Sign
Model No. 2552-00-001

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 2
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
To avoid burns, DO NOT touch the kettle or any heated surface.
DO NOT place or leave objects in contact with heated surfaces.
013_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 3
gmpopcorn.com
SAFETY PRECAUTIONS (continued)
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is critical that you call Gold Medal’s
Technical Service Department at -800-543-0862 for any questions about your
machine operations, replacement parts, or any service questions. (Gold Medal
Products Co. does not assume any liability for injury due to careless handling and/or
reckless operation of this equipment.) General images may be used in manual for
reference only.

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 4
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 0700 Medallion Drive, Cincinnati, OH 4524 USA -(800)-543-0862.
Model Description
2552-00-001: 2 oz. PopMax Popper with an LED lighted sign, and equipped with a
PowerOff
TM
Control feature.
Items Included with this Unit
Aluminum
Scoop
Measure
14.7 cc
12 oz. Corn
Measure
Black Crutc Tips
Knobs wit Tee Bolts
(for Popper Doors)
Knob wit Screw
(for Old Maid Pan)
Measure
1/2 Cup

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 5
gmpopcorn.com
Setup
This unit has been tested at the factory.
. Remove all packaging and tape prior to operation.
2. Place the unit on a sturdy, level base.
3. The Popper blower vents out the top of unit, allow adequate clearance for airflow.
4. The popper unit has 4 glide feet preinstalled at the factory (see image below). Install a
Black Crutch Tip on each of the 4 glide feet. Firmly push the crutch tip over the glide
until it covers the glide entirely.
5. Door knobs are shipped in the accessories pack located inside the machine. Install a
door knob with tee bolt on each popper door; install the knob with screw on the old
maid pan.
6. Make sure kettle lead-in cord is securely plugged into unit, and twisted to lock into the
kettle receptacle.
7. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of
this manual).
Black Crutc Tip
Glide
(pre
-
installed
at the factory)
General image s own for reference.

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 6
gmpopcorn.com
Electrical Requirements
The following power supply must be provided:
2552-00-001: 20 V~, 400 W, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install the unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 7
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
KETTLE HEAT SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the heating elements in the
popping kettle. The green switch light ON indicates there is power to the kettle heating
element.
KETTLE MOTOR SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the kettle agitator motor
and exhaust blower. The Kettle Motor Switch MUST be ON at all times when there is
popcorn (popped or un-popped) in the kettle. The green switch light ON indicates there is
power to the agitator motor and exhaust blower.
LIGHTS/WARMER SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the popcorn sign, interior
cabinet light, and heat element for the corn pan.
POWEROFF CONTROL
The PowerOff Control feature will automatically turn the kettle heat off after 5 minutes of idle
time (no popcorn popped). The PowerOff Control will prevent the heat element and thermostat
from cycling OFF-ON if the Kettle Heat Switch is left on. This feature saves electrical power and
extends the life of the kettle heating element and thermostat.
•When the Kettle Heat Switch is turned ON, and the kettle thermostat switches OFF,
the PowerOff Control’s 5 minute timer starts; the 5 minute timer resets each
time a batch of popcorn is popped.
•The small green neon light in the Kettle Heat Switch will blink OFF-ON to indicate
the kettle has been automatically turned OFF.
•To restart the kettle heating, cycle the Kettle Heat Switch OFF-ON.
Kettle Heat Switc
Kettle Motor Switc
Label used on units wit t e
PowerOff Control feature.
Lig ts/Warmer
Switc

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 8
gmpopcorn.com
Popping Corn
This section describes instructions for popping Standard (salted popcorn).
Amount of Popcorn and Oil
Your new popper is equipped with a corn, salt, and oil measure. We recommend flavored and
colored coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black
deposits in your kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers.
Ingredient amounts for popping Standard Popcorn:
Kettle
Size
Popcorn
C arge
Oil
C arge
Flavacol (Salt)
2 oz.
2 oz. (355 ml)
4
oz. (
8
ml)
Tblsp. (
5
cc)
For best results use Mega-Pop® 2 oz. premeasured pouches (Item# 2839).
Popping Standard (Salted) Popcorn
. Turn the Lights/Warmer, Kettle Heat and Kettle Motor Switches ON.
2. To determine when the kettle is ready to pop corn (about 4 minutes), test pop three
kernels of corn and one ounce (30 ml) of popping oil. When the kernels pop, the kettle
is ready for use.
3. Lift the kettle lid and load the Mega-Pop® premeasured popcorn and oil pouch into
kettle, or pour in the popcorn and Flavacol, then add oil in the premeasured amounts
specified above. Close lid.
4. When the corn has finished popping, gently dump the popcorn.
5. On the final kettle of corn, turn the Kettle Heat Switch OFF just as the lids are forced
open by the popping corn. This procedure saves electricity, since the kettle has plenty
of heat, and helps eliminate smoke/odor from any oil residue that remains after
popping has stopped.
6. When finished popping, make sure KETTLE HEAT and KETTLE MOTOR switches are
turned OFF.
NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN!
If Auto Shut-OFF is enabled, unit will automatically shut kettle heat OFF after 5
minutes of idle time (no popcorn popped). To restart kettle heating, cycle the Heat
Switch OFF-ON.

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 9
gmpopcorn.com
Care and Cleaning
DANG
ER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet.
Always unplug the equipment before cleaning or servicing.
025_111616
WARNING
To avoid serious burns, DO NOT touch the kettle while it is hot!
028_082715
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
Note: It is extremely important to follow all of the cleaning procedures, otherwise parts
damage and equipment failure will result. The warranty does not cover parts that
are damaged due to improper cleaning.
Daily Kettle Cleaning Instructions
CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool
at least hour before attempting to clean. DO NOT use ice or water to cool
down a hot kettle! Severe kettle damage will result!
. When cool, wipe the outside of the kettle with a clean, soft cloth. DO NOT use oven
cleaners or abrasive materials as they will damage the kettle.
2. Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons
per gallon of water. It is not necessary to use the entire gallon at once; only use
enough to fill the kettle /2 inch deep.
3. Turn the kettle heat ON. When the water starts to boil, turn the kettle heat OFF.
4. Allow to cool for at least hour, then dump the solution into a bucket and wipe the
inside of the kettle with a clean cloth. Make sure all of the solution goes into the
bucket; do not spill any in the interior of the machine.
For an extra dirty kettle, the process may be repeated; or, after turning the kettle heat
OFF, allow solution to sit in the kettle overnight. The next morning, dump the solution
into a bucket and wipe the inside of the kettle with a clean cloth.
5. With the unit OFF and unplugged, wipe the kettle lead cord with a clean SLIGHTLY damp
cloth. DO NOT get moisture into t e kettle lead-in cord, severe damage will result.

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 10
gmpopcorn.com
Daily Unit Cleaning Instructions
. With the machine OFF, unplug the unit and allow it to cool before attempting to clean.
2. Make sure to clean all pans/accessories in order to sanitize them before each use.
3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from the glass and cabinet.
4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless
steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.
5. Clean the glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item
No. 2588) is recommended.
Ammonia cleaners will damage the plastic doors. Use only non-ammonia cleaners,
such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).
Filter Cleaning Instructions
The popcorn machine is equipped with an efficient and durable filtration system. The filter
should be cleaned every -2 weeks to maintain maximum efficiency.
Steps to Clean Filter
Step 1: Turn unit OFF and allow it to cool before
removing filter. Filter is located inside the popcorn
machine, above the popping kettle.
Step 2: Remove filter by gripping the filter itself and
pulling straight down.
Step 3: Clean filter in warm soapy water, then rinse
and allow to dry overnight. Replace filter by putting it
into the slot and pushing upward. Make sure the filter
frame is flush with the ceiling of the popper (as shown
above).

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 11
gmpopcorn.com
Troubleshooting
Issue
Possible Cause
Solution
No Power to t e Unit
A.
No
Power to
the
Unit
A.
Make sure the
unit’s power
cord is plugged in.
Kettle Does Not Heat
A.
Power to the Kettle
A.
Make sure kettle lead
-
in cord is plugged in and
twisted to lock into the kettle receptacle.
B.
Kettle Heat Switch
B.
Have a qualified service person c
heck the
voltage to and from the Kettle Heat Switch; if
switch is defective, replace it.
C.
PowerOff Control
C.
Units with the PowerOff Control feature, kettle
heat will automatically shut OFF after 5
minutes of idle time (no popcorn popped).
The small green neon light in the Kettle Heat
Switch will blink OFF-ON to indicate the kettle
has been automatically turned OFF.
To restart kettle heating, cycle the Heat Switch
OFF-ON. Reference the Controls and Their
Functions section of this manual.
D.
Heating Element
D.
Heating element in the kettle may
be burned
out. Check with a qualified service person for
inspection/repair.
Long Popping Cycles
(Longer than 4 minutes for
Salt Popcorn)
A.
Low Voltage
A.
If the
machine is operated on low voltage, this
could cause the kettle not to reach the proper
operating temperature. Check with a qualified
electrician.
B.
Inadequate Supply Lines
B.
Inadequately sized electrical supply lines
or
use of extension cord, in addition to being a
fire hazard, would also prevent the kettle from
reaching the proper operating temperature.
Check with a qualified electrician.
C.
Inferior Corn
C.
Inferior quality corn would result in longer
popping cycles. Use only top quality hybrid
popcorn from reputable suppliers. Even then,
if you let your corn pick up moisture or dry
out, your popping cycles will be slow.
A.
Kettle Motor Switch
A.
If the kettle agitator shaft is not rotating,
DO NOT pop corn. Make sure the Kettle Motor
Switch is ON. If the switch is ON, and the shaft
is not rotating, the switch or motor may be
faulty, contact qualified service personnel for
inspection/repair.
B.
Kettle Agitator
S
haft
/Stir
Blade not rotating. (Unit
must be OFF, unplugged
and cool prior to
c ecking or adjusting
t e agitator assembly.)
B.
If the kettle agitator shaft is not rotating,
DO NOT pop corn. Kettles wit a FLOATING
Stir Rod – lift the agitator weight and check
the clearance between the shaft and the kettle
bottom; it should be a minimum of /32”
(thickness of a dime). To make shaft
adjustments, reference the Agitator Set Collar
Adjustment section.

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 12
gmpopcorn.com
Agitator Set Collar Adjustment
The following instructions describe how to properly adjust set collars on an agitator assembly
with a floating stir rod.
Drive Motor
Spur Gear
Agitator’s Spur Gear
(should set halfway up on
Drive Motor Spur Gear)
Set Collar
w/Set screw
Spur Gear Place
ment
Needle Bearing
(should set at least
halfway into Gear Block)
Gear Block
Step 1:
Turn machine OFF, unplug unit
,
and
allow it to cool completely before attempting
to adjust the agitator height.
Step 2: Loosen the set screw in each set collar
to be adjusted.
Step 3: With the kettle mounted in the popper,
adjust the shaft so the Spur Gears are halfway
engaged, and the Needle Bearing is at least
halfway engaged in the gear block (reference
image at right).
DO NOT set spur gears at full gear contact; it
can cause binding as the kettle is dumped.
Step 4: Snug tighten only, the set screw in set
collar above the crossbar to hold position. Then,
lift the agitator weight and check the clearance
between the shaft and the kettle bottom. If
there is adequate clearance, fully tighten the set
screw to secure set collar in place.
Step 5: Adjust clearance between the bottom of
the crossbar and the lower set collar to /32”
(thickness of a dime); then re-tighten set screw
to secure in place (reference image).
Step 6: Adjust set collar for agitator weight to
be between 3/ 6” to /4” above the agitator
weight. Once adjusted,
re-tighten set screw
to secure in place.
Agitator s own for general
image reference only (lids
not s own for clarity).
Adjust clearance to
t ickness of a dime.
3/16” to 1/4” max.
Steps to Adjust Set Collars
Set Coll
ar above Crossbar
Lower Set Collar
(below Crossbar)
Set Collar
(for Agitator Weight)
Agitator Weig t
Stir Rod
Crossbar
Agitator S aft

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 13
gmpopcorn.com
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGE
R
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 14
gmpopcorn.com
ORDERING SPARE PARTS
. Identify the needed part by checking it against the photos, illustrations, and/or
parts list. (General images may be used in manual for reference only.)
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to:
Parts Department
Gold Medal Products Co.
0700 Medallion Drive
Cincinnati, Ohio 4524 -4807
Or, place orders by phone or online:
Phone: [phone]
(5 3) 769-7676
Fax: [phone]
(5 3) 769-8500
E-mail: [email protected]
Web Page: gmpopcorn.com

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 15
gmpopcorn.com
Replacing Broken Glass
Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be
obtained from a local glass shop, always purchase tempered glass.
GLASS DIMENSIONS (Height x Width x Thickness)
Front and Side Glass: 2 /4” X 6 7/8” X /8” (3 Pieces)
. With the machine OFF, unplug the unit and allow it to cool before attempting to
replace any glass.
2. Carefully remove all loose pieces of broken glass.
3. Pull out Magnetic Clip (located above glass panel in cabinet interior) to remove (see
Figure A below).
4. Slide glass panel up under top ridge, then swing the bottom of the panel out and lower
it away from unit (see Figures A and B below).
5. Carefully remove the rest of the broken glass.
6. Remove all rigid glass channels from around the glass to be replaced, set channels
aside for reuse.
7. Apply decals (if desired) to the new glass panel.
8. Slide rigid glass channels over the exposed edges of the new glass panel.
9. Carefully slide new glass panel up under top ridge, then lower it into the bottom channel.
0. Reinstall magnetic clip above the new panel in cabinet interior.
Figure A
-
Remove magnetic
clip located above glass panel.
Figure C
–
Swing bottom of
glass panel out, then lower
it away from unit.
Figure B
-
Slide
glass panel
up under top ridge.
Magnetic
Clip
General images s own
for glass installation reference only.

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 16
gmpopcorn.com
12/14 oz. Kettle Assembly (58014) – Agitator Assembly View
Item Part Description Part Number
58014
/4
-
20 X /2 THUMB SCREW
6 059
2
8
-
32 x /2 FH MS PH
06064
3
KETTLE & SHELL BLOCK
6 0 3
4
DUMP HANDLE
–
BLOCK WELDMENT
88769
5
DUMP HANDLE KNOB
47 0
6
8
-
32
X
FL HD P
H MS
20068
7
LID & AGITATOR ASSY (Complete Assembly)
580 6
8
KETTLE CROSSBAR ASSEMBLY
580 5
9
FRONT
KETTLE LID
47720
0
REAR KETTLE LID
47 9
AGITATOR BEARING HUB
43434
2
NEEDLE BEARING
47 06
3
SPUR GEAR KIT (Includes 2 gears with set
screws. Always replace Agitator Spur Gear and
Kettle Drive Motor Gear as a set.)
47059K
4
SET SCREW # 0
-
32 X 3/ 6
4 742
5
2/ 4 OZ.
AGITATOR SHAFT
697 2
6
SET COLLAR 5/ 6 ID 5/8 OD
46649
7
AGITATOR WEIGHT
697 5
8
6 OZ.
STIR ROD
69806
Co
mplete Agitator Assembly
(Includes Lids)
8 9 10
7
4
1
6
See Kettle
Bottom
Assembly.
Complete Kettle Assembly
Overall
Kettle 61 054EX
Crossbar Assembly 56000
4 5
1
3
2
15
16, 14
18
17
11
12
13*
14
*See Parts
List note.

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 17
gmpopcorn.com
12/14 oz. Kettle Assembly (58014) – Kettle Bottom View
Item Part Description Part Number
58014
2/ 4 OZ. KETTLE BOTTOM ASSEMBLY
(includes parts listed below) 580 2
2
KETTLE SHELL
6 0 7
3
KETTLE LEAD ASSY
6 226
4
KETTLE GASKET
6 0 2
5
KETTLE INTE
GRAL HTR 2/ 4
580
6
2/ 4OZ SHUNT BAR
77879
7
8
-
32 TOP LOCK NUT (always replace if removed)
67943
8
482°F THERMOSTAT (includes two 6
-
32 screws)
76708
9
THERMOSTAT SHUNT BAR
47 93
0
550°F THERMOSTAT (includes two 6
-
32 screws)
77 08
9 10 8
Element
View
Lock Nut View
Top Lock Nut
-
Fastens
each thermostat and
ground. Install Lock Nut
with triangle in UP
position (as shown).
ONE TIME USE ONLY,
REPLACE NUT if
removed.
T ermostat
Welded Stud
7
58220 Kettle Bottom A ssembly
58220 Element Vie w
2
3
Kettle Bottom Assembly
1
5
4
6

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 18
gmpopcorn.com
Cabinet Exterior – Front View
Item Part Description Part No.
8
-
32 X 3/8 SLT. HWH M/S
42044
2
DOME WELDMENT
4 7
3
2 5/ 6”
GLASS CHAN
NNEL
(u
sed on
the
side
edges of the glass panels) 49844
4
6 /4” GLASS CHANNEL
(u
sed on
the
top and
bottom edges of the glass panels) 74 72
5
GLIDE
47328
6
0
-
24 X 3/4
” HEX HEAD
4 3 4
7
CRUTCH TIP BLACK 70 DURO
49 23
7
5, 6
2
See Kettle
Assembly
Section
1
See Lig ted
Sign Section
3
For Glass Panels,
see Replacing
Glass section.
4
Model 2552
-
00
-
001

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 19
gmpopcorn.com
Cabinet Exterior – Rear View
Item Part Description Part No.
MAGNETIC C
ATCH
4756
2
MAGNETIC CATCH BRACKET
4 340
3
MACNETIC BRACKET SHIM
38527
4
**
COMPLETE LH DOOR HARDWARE KIT
47054
5
**
COMPLETE RH DOOR HARDWARE KIT
47055
6
8
-
32 X /2 PHIL PAN M/S (f
astens male hinges to
the corner posts) 47 4
7
DOOR
77774
8
DROP PAN
EL
77730
9
OLD MAID PAN
49 00
0
LID LIFT KNOB
47 20
8
-
32” X 3/8” PH PAN W/SEMS
42227
3
STRAIN RELIEF SR
-
7W
-
2
67060
2*
LEAD IN CORD 5 AMP PLUG
87085
3
1, 2
4**
5** 6
7
For Labels, See
Safety Labels
Section 8
10, 11 9
*
CAUTION: If supply cord is damaged, it must be replaced
by Gold Medal Products Co., its service agent, or
similarly qualified persons in order to avoid a azard.
13*
12
**
Complete
Door
Hardware Kit
(See next page for individual
component breakdown).
2387
-
00
-
0 0
General image s own
for parts reference only.

PopMaxx with
Lighted Sign Model No. 2552-00-001
Page 20
gmpopcorn.com
Door Hardware Kits – Individual Component Breakdown
Item Part Description Part Number
47054
47055
DOOR KNOB
4 0 3
4 0 3
2
8
-
32 X ½ SCREWS PH PAN W/SEMS
47 24
47 24
3
ACORN NUT #8
-
32
47702
47702
4
TEE BOLT
75267
75267
5
MALE HINGE SHORT LEFT
4 349
6
FEMALE HINGE LONG LEFT
4 352
7
FEMALE HINGE LONG RIGHT
4 35
8
MALE H
INGE SHORT RIGHT
4 350
4
3
8
7
6 5
1
2
3
2
Complete Left Hand Door
Hardware Kit (P/N 47054)
(contains all parts s own above)
Complete Rig t Hand Door
Hardware Kit (P/N 47055)
(contains all parts s own above)