Graco 246085 Guide

309867G
EN
Installation-Operation
Data Reporter
Part No. 246085
Records actual temperature, temperature setpoint, actual pressure, pressure setpoint, cycles,
and diagnostic code data from Reactor™proportioner.
Downloads data to PC with Microsoft®Windows 98 though Windows XP.
Part No. 248848
Data Reporting Kit without interface module.
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.

InstallHardware
2309867G
Install Hardware
For 246085 only. For Kit 248848 continue on step 12.
5. Open Reactor cabinet.
1. Turn Reactor main power OFF . Disconnect
power supply.
WARNING
Read warnings in Reactor repair manual. Wait 5 min
for stored voltage to discharge (E-30 and E-XP2 mod-
els only).
2. Remove side plate (A). The plate is on the right side
of the Electric Reactor (shown) and on the left side
of the Hydraulic Reactor.
TI2500a
A
3. For Electric Reactor, thread wires (B, C) and cables
(H, P) of interface module (1) through boot in top of
cabinet.
For Hydraulic Reactors, orient power supply 90° as
shown by moving DIN rail (only 1 nut is used).
4. Attach interface module (1).
TI3576a
P
TI19356a
H
C
B
P
H
C
B
Electric Reactor Hydraulic Reactor
TI3575a
1
TI7999a
1
Electric
Reactor
Hydraulic
Reactor

Install Hardware
309867G 3
6. Put on static conductive wrist strap.
CAUTION
Before handling boards, put on a static conductive
wrist strap to protect against static discharge which
can damage boards. Follow instructions provided with
wrist strap.
7. Connect HEAT cable to temperature control module
data connector.
Temperature Control Module
Data
8. Connect PUMP cable to J12 on motor control board.
TI2576a-1
J12
TI3153a-1
J12
Models E-30 and E-XP2
Models E-20 and E-XP1
TI7724
Models Hydraulic Reactors
J12

InstallHardware
4309867G
10. Close Reactor cabinet.
9. Insert wires (B, C) in top front terminals of fuse block
(F) at circuit breaker module. Tighten screws (S).
11. Drill holes as follows:
a. For Electric Reactor, drill holes using bracket (4)
as template. Apply sealant (4c) to screw
threads. Mount with screws (4a) and nuts (4b).
TI2514a
F
C
B
S
TI3581a
ti3574A
4
b. For Hydraulic Reactor, drill two holes exactly as
shown below. Be careful not to damage compo-
nents inside cabinet when drilling holes. Apply
sealant (4c) to screw threads. Mount bracket (4)
with screws (4a) and nuts (4b).
12. Connect Reporter cable to interface plug (D).
13. Reconnect power supply. Turn Reactor main power
ON . Main screen will appear on Reporter,
see page 5.
Reporter is now ready to record data from Reactor,
see page 5. To download data, first Install Soft-
ware, page 7.
ti7998A
Two 3/16 in. (5 mm)
diameter mounting
holes
2.75 in.
(70 mm)
3.00 in.
(76 mm)
0.93 in.
(24 mm)
TI3575a
D
TI7999a
D
Electric Reactor
Hydraulic Reactor

Keypad
309867G 5
Keypad
Key:
R Record key
SSetupkey
EEnterkey
A Arrow keys (up, down, left, right)
CCancelkey
D Download key
Screens
Main Screen
Main screen appears when powered up.
Press . Following message will appear momen-
tarily, followed by Record screen.
Record Screen
Displays A, B, and hose temperatures, A and B pres-
sures, cycles, and remaining recording time. Display
reflects selections made on Setup screens, page 6.
Press or to stop recording.
R
S
E
A
C
D
Reporter displays data received from Reactor. It is
not a remote control for Reactor.
GRACO REPORTER
REV 1.01
MAR 20 2003 12:48:12
45:32 HOURS LEFT
GETTING
REACTOR STATUS
PLEASE WAIT
If following message appears with audible alarm,
Reporter is not properly connected to Reactor.
Check connection.
NO REACTOR
PRESENT
RECORDING ABORTED!
ABHOSE
°F 160 160 160
PSI 1200 1200
CYCLES 0 45:32
If hose zone is in current control mode, display will
show hose current, for example 14A.

Screens
6309867G
Setup Screens
Display must be at main screen, page 5. Press to
enter Setup. Press or to move through
Setup menu. Press to select.
Press or to exit Setup.
Recording Period
Reporter updates records at set intervals. At default of
10 sec, Reporter has 52:11 hours of recording time.
Changing to 30 sec increases recording time to 156:33
hours; 1 min increases to 313:06 hours.
Press .
Press or to move through menu. Press
to select.
Change Units
Press .
Press or to move through menu. Press
or to move ∗ between units. Press
to select.
Date/Time Change
Press .
Press or to change values. Press or
to move cursor. Press to select.
SETUP ↓
RECORDING PERIOD
CHANGE UNITS
DATE/TIME CHANGE
SETUP ↑
DELETE RECORDS
SETUP ↓
RECORDING PERIOD
CHANGE UNITS
DATE/TIME CHANGE
SELECT RECORD PERIOD
10 SECONDS
30 SECONDS
1 MINUTE
SETUP ↓
RECORDING PERIOD
CHANGE UNITS
DATE/TIME CHANGE
CHANGE UNITS
TEMP ∗°F °C
PRESSURE ∗PSI BAR
SETUP ↓
RECORDING PERIOD
CHANGE UNITS
DATE/TIME CHANGE
DATE: MAR 20 2003
TIME: 1 2:48:12

Install Software
309867G 7
Delete Records
Press .
Press to delete. Press to exit.
Install Software
1. Close all programs and applications.
2. Insert software CD (6) in CD ROM drive. If install
starts automatically, go to step 6. If install does not
start automatically, go to step 3.
3. From file menu in program manager or file manager,
choose Run.
4. Type: d:\setup.exe (use letter corresponding to your
CD ROM drive).
5. Press ENTER.
6. Follow instructions on screen. Software will load
Reactor Downloading program to Start menu and
will place icon on desktop.
SETUP ↑
DELETE RECORDS
DELETE RECORDS?
ENTER TO DELETE
CANCEL TO EXIT
ALL RECORDS
WERE DELETED
The Reactor Downloading program operates on
PCs with Microsoft®Windows 98 or later.
On some PCs a Restart may be necessary after
program is loaded.

Downloading
8309867G
Downloading
Hardware Connections
1. See drawing on page 14. Connect cable (7) to con-
verter (2) and to appropriate serial port on PC.
2. Remove Reporter cable from Reactor interface
module (1) and insert in converter (2).
3. Connect power supply (8) to converter (2). Plug
power supply into outlet.
Run Program
Main Window
Locate Menu Bar (M) and Tool Bar (T), for reference.
See FIG. 1.
Start Reactor Downloading program on PC. Check that
status indicator (L) at upper right of main window is
green; also see Status Bar (S).
If PC uses a USB port, connect a USB to RS-232
serial adapter between the PC and cable (7).
Clicking status indicator (L) turns CommPort
Enable on and off, provided Reporter is properly
connected to PC.
If indicator is red and following message appears,
connection is broken.
Check that:
• CommPort is enabled
• correct CommPort is selected (CommPort
Properties window)
• cable (7) is connected properly, see left
• Reporter is displaying main screen, page 5.

Downloading
309867G 9
FIG. 1. Main Window
L
M
T
S

Downloading
10 309867G
Get Log File
1. Access by File>Get Log File on menu bar, or left
button on tool bar.
2. Application will prompt you to open a log file. Enter a
file name. Do not use spaces in the file name.
3. Click Open.
4. Data will download to log file. Download screen will
display. Downloading an entire set of records will
take about 3 minutes.
Get Uncompressed Log File
1. Access by File>Get Uncompressed Log File on
menu bar, or left button on tool bar.
2. Continue to follow Get Log File procedure at left.
Downloading an entire set of records will take about
15 minutes.
View Log File
1. Access by File>View Log File on menu bar, or right
button on tool bar.
2. File can be opened as a text file in Notepad or
Wordpad, or in a spreadsheet program such as
Microsoft Excel, page 11.
Exit
Exits program.
DOWNLOAD
IN PROGRESS
34% COMPLETE
If following message appears with audible alarm,
Reporter is not properly connected to PC. Check
connection.
NO RESPONSE FROM PC
DOWNLOADING
DID NOT OCCUR
OR
23
For non-English Microsoft Windows XP operating
systems, “Get Uncompressed Log File” should be
used if the “Get Log File” command fails. The
uncompressed option takes about five times longer
than the compressed mode.
OR
OR