Graco 214-627 User manual


INSTRUCTIONS–P ARTS LIST 307–318
Rev. H
Supersedes G
2 Quart Pressure Cup
50 psi (3.5 bar) Maximum Working Pressure
Part No. 214–627, Series B
0–50 psi (0–3.5 bar) Regulated Pressure Range
Part No. 235–117, Series A
0–15 psi (0–1 bar) Regulated Pressure Range
Table of Contents
Preparation for Operation 2. . . . . . . . . . . . . . . . . . . . . . .
Operation 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts 4–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco T oll-Free Phone Numbers 6. . . . . . . . . . . . . . . . .
Technical Data 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING
Hazard of using Fluid Containing Halogenated Hydrocarbons
Never use 1, 1, 1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluid
containing such solvents in this equipment. Such use could result in a serious chemical reaction, with the
possibility of explosion, which could cause death, serious bodily injury and/or substantial property damage.
Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum parts.
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
�COPYRIGHT 1978, GRACO INC.
This manual contains important
warnings and information.
READ AND RETAIN FOR REFERENCE


Preparation for Operation
Prepare the paint or other coating according to the
manufacturer’ s instructions. Strain the paint through a
fine nylon mesh bag, available at paint dealers. Fill the
cup (Ref No. 27, page 4) with paint and screw it se -
curely to the lid (19). T orque to 65 in–lb (10 N.m).
Connect the air (23) and fluid (25) hoses as shown in
Fig. 1. The recommended auxiliary equipment shown
in Fig. 1 can be found in the Accessories section on
page 6.
Fig. 1
KEY
AMain Air Supply
BOn–Of f V alve
C 1/4 npt Air Inlet
D Air Filter
ELocking Screw
FAir Spray Gun
G
Air Adjusting V alve
5
Air Regulator
20 Air Control V alve
23 Air Hose
25
Fluid Hose
A
B
D
C
5
E
20
25
23
F
G



Operation
WARNING
To reduce the risk of over-pressurizing the equip -
ment, which could cause serious bodily injury , in -
cluding splashing in the eyes or on the skin,
never exceed 50 psi (3.5 bar) air pressure to the
cup. The relief valve is preset to relieve pressure at
50 psi (3.5 bar). Do not alter settings on the relief
valve.
1. T
urn on the air supply .
2. T
urn the cup air control valve (20) clockwise , all
the way in.
3. T urn the air regulator (5) knob in until the gauge
reads 10 psi (0.7 bar). Turn the air regulator ’ s lock -
ing screw (E) clockwise to lock it and counterclock-
wise
to unlock it.
4. Spray a test panel. If the paint is not fully atom -
ized, either decrease the cup fluid pressure with
the air regulator (5), or increase the atomizing air
pressure with the air adjusting valve (G). Always
use the lowest possible pressure needed to
achieve the desired results.
5. T o decrease the cup fluid pressure, turn the air
regulator (5) knob out (counterclockwise) . T urn the
cup air control valve (20) counterclockwise mo-
mentarily to bleed of f the excess air . Then reset it
by turning in the air regulator knob.


Service
Cleaning the Cup
WARNING
To reduce the risk of serious bodily injury , including
splashing in the eyes or on the skin, always re-
lieve pressure in the cup (27) before removing the
lid (19) by turning the air regulator (5) knob all the
way out (counterclockwise) and unscrewing the air
control valve (20) thumbscrew .
1. Relieve
pressure in the cup by following the warning
above.
2. Unscrew the air cap retaining ring on the spray gun
about
3 turns. Hold a rag over the air cap and trigger
the gun to force paint back through the hose (25) and
into the cup (27).
3. Turn of f air supply . Empty the paint from the cup (27)
and clean the cup and lid (19). Be sure the solvent
used
is compatible with the fluid being sprayed.
4. Check the gasket (15) inside the lid (19). Replace if
damaged.
NOTE: When replacing gasket (15), remove old adhe-
sive
from inside lid (19). Apply new adhesive (3M
#847 Scotch–Grip � or equivalent) to the lid when
installing the new gasket.
5. Remove the air cap from the spray gun and turn off
the air regulator (5). Fill the cup (27) with solvent,
replace
lid (19), and close the air control valve (20).
6. Turn on the air supply. Set the air regulator (5) at
10 psi (0.7 bar) and hold the spray gun trigger open
until clean solvent comes from the gun.
7. Remove the solvent from the system and wipe the
equipment
with a solvent dampened rag.
Parts
10
2
14
9
13
20
Place wrench
here to remove
19
*15
*7
*17
12
8
1
29
22
23
24
26
25
27
Slots on bottom for assisting
in cap removal
28*
11
6
21
3
4*
18
16
Ref 25
Ref 23
5*




*
*

Parts
Model 214–627, Series B
0–50 psi (0–3.5 bar) Regulated Pressure Range
Includes items 1–29
Model 235–117, Series A
0–15 psi (0–1 bar) Regulated Pressure Range
Includes items 1–29
Ref.
No. Part No. Description Qty.
Ref.
No. Part No. Description Qty.
1 100–032 SCREW
, rd hd; 6–32 x 1/4” 1
2 100–188 NUT
, hex; 5/16–18 1
3 101–855 SCREW
, rd hd, self–tapping;
No. 4 x 3/16” 2
104–655
GAUGE, pressure;
Model 214–627 only 1
111–500
GAUGE, pressure;
Model 235–1 17 only 1
104–815 REGULAT
OR, air; adjustable
See Manual 308–167;
Model 214–627 only 1
111–501 REGULAT
OR, air; adjustable;
Model 235–1 17 only 1
6 183–697
NIPPLE; 1/8 npt 1
7* 172–593* VAL
VE, check 1
8 172–594 BRACKET
, check valve 1
9 172–613
ADAPTER, handle 1
10 172–620 HANDLE 1
11 172–621
ADAPTER, 7/16 unf(m)
x 1/8 npt(m) 1
12 172–622 W
ASHER, flat; 1/4” 1
13 172–679 NUT
, hex; 3/8” x 1/8” 1
14 172–680 ELBOW
; 1/2 uns(f) x 3/8 npsm(m) 1
15* 183–337 GASKET
, cap 1
16 172–682
ADAPTER; 3/8 npsm(m)
x 1/2 uns(f) 1
17* 172–684
SPRING, compression 1
18�183–696
TEE; 1/4 npt(m) x 1/4 npt(m) x
1/8 npt(f) 1
19 174–069 LID 1
20 174–075 VAL
VE, air control 1
21 174–100
CHAIN, ball; 3” (76.2 mm) long 1
22 176–243 LABEL 1
23 212–005
HOSE, air; 1/4” ID, 6’ (1.83 m)
long; cpld 1/4 npsm(fbe) swivel;
Includes item 24 1
24 104–415 .COUPLING 2
25 212–006
HOSE, fluid; 1/4” ID, 6’–8” (2.03 m)
long; cpld 3/8 npsm(fbe) swivel;
Includes item 26 1
26 104–084 .COUPLING 2
27 214–602 CUP 1
28*�214–691 VAL
VE, relief; 50 psi (3.5 bar). 1
29 172–881 TUBE 1
306 & 307 numbers in description refer to separate
instruction manuals.
* Recommended ”tool box” spare parts. Keep on hand
to reduce down time.
Kits
�Relief V alve Kit 218–925
Model 214–627, “Series A” cups must order this kit to
replace the relief valve (item 28) and tee (item 18). The
kit includes Relief V alve 214–691 and the appropriate
tee. Series A Pressure Cups must have both the tee
and relief valve replaced together for safety reasons.
Conversion Kit 235–115
To convert Model 214–627 Pressure Cup to Model
235–1 17 Pressure Cup. Kit includes the following
parts.
Part No. Description Qty.
111–500
GAUGE, pressure 1
111–501 REGULAT
OR, air; adjustable 1


Accessories
Use Only Genuine Graco Parts and Accessories
Air Spray Guns
See the following manuals to select the appropriate
gun for your application.
Manual
No.
307–378
307–379
307–380
Model
No.
600
700
800
Maximum W orking
Pressure
200 psi (14 bar)
200 psi (14 bar)
900 psi (62 bar)
Air Line Filter 106–148
250 psi (17 bar) Maximum Working Pressure
Removes harmful dirt and contaminants from the com -
pressed air supply. 3/8 npt inlet and outlet.
Air Line Filter & Regulator 202–660
180 psi (12.6 bar) Maximum Working Pressure
1/2 npt(f) inlet and two 1/4 npt(m) outlets.
Air Adjusting V alve 205–090
100 psi (14 bar) Maximum Working Pressure
For controlling atomizing air to the gun. 1/4 npsm(m)
inlet and 1/4 npsm(f) swivel outlet.
Buna–N Air Hose (with neoprene cover)
200 psi (14 bar) Maximum Working Pressure
With reusable couplings and compression sleeves.
5/16 in. (7.9mm) ID, 1/4 npsm (fbe) swivel.
Part No.
210–866
210–867
210–868
Length
15’ (4.5 m)
25’ (7.6 m)
50’ (15.2 m)
Nylon Fluid Hose 221–195
225 psi (15 bar) Maximum Working Pressure
1/4 in. (6 mm) ID, 6 ft. 8 in. (2.03 m) long,
3/8 npsm(fbe) swivel.
2 Quart Cup Liner 1 12–491
Packaged 20 in a box.
Polyethylene bag for easier cleanup.
Graco Phone Numbers
TO PLACE AN ORDER , contact your Graco distrib -
utor
, or call this number to identify the distributor
closest to you: 1–800–367–4023 T oll Free
FOR TECHNICAL ASSIST ANCE, service repair
information or assistance regarding the application of
Graco equipment: 1–800–543–0339 T oll Free


Notes


The Graco Warranty and Disclaimers
WARRANTY
Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the
date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser ’ s sole remedy for breach of this war -
ranty,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective.
This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’ s written recommen -
dations.
This warranty does not cover , and Graco shall not be liable for , any malfunction, damage or wear caused by faulty installation, misap -
plication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco
component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation
or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Graco to verify the
claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be
returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or
workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor and transportation.
DISCLAIMERS AND LIMIT ATIONS
THE TERMS OF THIS W ARRANTY CONSTITUTE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY OTHER W ARRANTIES (EXPRESS
OR IMPLIED), INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND OF ANY NON–CONTRAC-
TUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR STRICT LIABILITY . EVER Y FORM OF LIABILITY FOR DIRECT , SPECIAL OR
CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSLY EXCLUDED AND DENIED. IN NO CASE SHALL GRACO’S LIABILITY EXCEED THE AMOUNT OF THE
PURCHASE PRICE. ANY ACTION FOR BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.
EQUIPMENT NOT COVERED BY GRACO W ARRANTY
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH
RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS, OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not
manufactured by Graco (such as electric motor , switches, hose, etc.) are subject to the warranty , if any , of their manufacturer . Graco
will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
Technical Data
Maximum W orking Pressure 50 psi (3.5 bar) . . . . . . . . .
Regulated Pressure Range
Model 214–627 0–50 psi (0–3.5 bar) . . . . . . . . . . . . .
Model 235–1 17 0–15 psi (0–1 bar) . . . . . . . . . . . . . .
Diameter 5.25 in. (133 mm). . . . . . . . . . . . . . . . . . . . . . . .
Overall Height 17.75 in. (451 mm) . . . . . . . . . . . . . . . . . .
Weight 4 lb (1.8 kg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wetted Parts Polyethylene, Aluminum, . . . . . . . . . . . . .
Nylon, Stainless Steel
Scotch–Grip�is a registered trademark of the 3M
Company.
Manual Change
Summary
This manual was revised to add 2 Quart Cup Liners,
Part Number 1 12–491, to the accessories.
Sales Offices: Atlanta, Chicago, Dallas, Detroit, Los Angeles, Mt. Arlington (N.J.)
Foreign Offices: Canada; England; Korea; Switzerland; France; Germany; Hong Kong; Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
PRINTED IN U.S.A. 307–318 4/78 Revised 6/94