GVS T Series User manual

Outdoor Station
T Series 2-Wire Outdoor Station(Surface Mounting)
User Manual_V1.0
T-OS06/T-OS10
User Manual

Content
Chapter 1 Function Overview................................................................................. 1
1.1 Function............................................................................................................. 1
1.2 Parameter.......................................................................................................... 1
Chapter 2 Product Introduction............................................................................. 2
2.1 Front View..........................................................................................................2
2.2 Product Dimension......................................................................................... 3
2.3 Interface Introduction..................................................................................... 4
Chapter 3 Installation................................................................................................5
3.1 Installation Height........................................................................................... 5
3.2 Installation Steps............................................................................................. 6
Chapter 4 User Instruction...................................................................................... 8
4.1 Calling resident................................................................................................ 8
4.2 Unlock.................................................................................................................8
4.3 External camera extension........................................................................... 9
Chapter 5 Settings..................................................................................................... 9
5.1 Factory Setting................................................................................................. 9
5.2 Unlock Time Setting........................................................................................9
5.3 Calling Volume Setting...................................................................................9
5.4 Address Setting................................................................................................9

1
Chapter 1 Function Overview
This product is an Outdoor Station in 2-wire analog video door phone system. Twin-core
cable is adopted to connect into the system. It supports video intercom with Indoor
Monitor and door unlocking. With the Relay Actuator Control Module connected, it also
supports unlocking 2nd door.
1.1 Function
Support calling to Indoor Monitor 1 and Indoor Monitor 2
Adjustable unlock time
Door status detection
Support external camera extension (Camera Interface Module is needed )
1.2 Parameter
Working Parameter
Working Voltage：DC 24~32V
Static Current：≤ 20mA (DC 30V)
Working Temperature：-25℃~55℃
Working Current：≤ 110mA (DC 30V)
Storage Temperature：-40℃~70℃
Dimension(H/W/D)：168×86×26mm
Camera
Type：CMOS
Resolution：600TVL
View Angle：90°(Horizontal )
Min. Illumination：0.1 lux
White Balance：Automatic
Fill-in Light Type：Light Sensitive Diode

2
Chapter 2 Product Introduction
2.1 Front View

3
2.2 Product Dimension
Unit：mm

4
2.3 Interface Introduction
Interface①
Unlock time setting;
Interface②
calling volume setting;
Interface③
BUS-A , BUS-B: Bus interface;
NO, COM , NC: Normal open/close interface;
GS: Door status detection interface;
DOOR SW: Unlock inside;
GND: Common ground.
③
①
②

5
Chapter 3 Installation
3.1 Installation Height
Suggested Installation Height: camera is 1.6m above the ground

6
3.2 Installation Steps
Step 1: Drill holes on the wall according to the installation size (149.5×64.5mm), fix the
capsules into the hole (it is recommended to align the device to the center of the
reference line ), then place the device and fasten with self-tapping screws(Pic 2).
Step 2: Fill the paper with apartment’s
information, and install it in the name
tag area, then complete the wiring
(Pic 3).
Pic 1
Pic 2
Pic 4
Step 3: Assemble the metal case
onto the device, and fasten with
plum blossom screw(Pic 4).
Pic 3
name tag pager
name tag cover

7
3.3 System Wiring
Remarks：
1The outdoor station is suitable for villa system with one or two apartments, and it is
possible to make connection with large system;
2Support multiple Indoor Monitors(maximum Qty is 4pcs) in one apartment, address
of all Indoor Monitors in one apartment should be same;
Attention: When there’s multiple monitors in one apartment, only one can be set
as master Indoor Monitor, otherwise there will be an over-current. Please check
the interface introduction for how to set a master Indoor Monitor.
3When there are multiple Indoor Monitors in one apartment and after they are called,
all Indoor Monitors will ring at the same time but only the screen of the master Indoor
Monitor is turned on, and after one of the monitors pick up the call, the rest monitors
hang up;
Remarks：
Indoor Monitor
Power Supply
Outdoor Station

8
4Power supply is limited, so only 2 monitors are allowed to be operated at the same
time (intercom function is not limited);
5The wiring above is recommended for villa system. If there are multiple Indoor
Monitors in one apartment，wiring with distributors(Star topology) are recommended.
Chapter 4 User Instruction
4.1 Calling resident
Single Calling Function Outdoor Station T-OS06 :
By short pressing the button of T-OS06(Upper button/ Lower button), visitor starts to call
the same Indoor Monitor 1, whose ringtone will echo back. Repeating pressing the
buttons during the call, then the countdown will be reset (each call waits for 30 seconds);
if there’s no answer in 30 seconds, the call will be ended.
Dual Calling Buttons Outdoor Station T-OS10:
T-OS10 supports calling Indoor Monitor 1 and Indoor Monitor 2. By short pressing the
lower button of T-OS10, visitor starts to call Indoor Monitor 1. By short press the upper
button of T-OS10, visitor starts to call Indoor Monitor 2. If the upper button is pressed
while calling Indoor Monitor 1, then the call will be switched to Indoor Monitor 2 and the
countdown will be reset (each call waits for 30 seconds). If there’s no answer in 30
seconds, the call will be ended.
4.2 Unlock
1) Unlock by Indoor Monitor
Door can be opened by Indoor Monitor when it’s communicating with Outdoor Station or
under surveillance mode.
2) Unlock by external push button
As there is an interface for integration of external push buttons, when this is connected,
a normal push button can be used to unlock the door.

9
4.3 External camera extension
Outdoor Station is supported to work with Camera Interface for external camera
extension. As Outdoor Station been well configured with Camera Interface, while
Outdoor Station is calling Indoor Monitor, or Indoor Monitor is monitoring Outdoor
Station, the displays can be switch between different cameras. For further information
please refer to the user manual of Camera Interface.
Chapter 5 Settings
5.1 Factory Setting
Cut off the power of the outdoor station and power on within 60 seconds, long press any
button on the outdoor station for 3 seconds. After a long beep, factory reset is done.
5.2 Unlock Time Setting
The default unlock time is 1 second. There is an adjustable potentiometer on the back
side of the outdoor station(①), unlock time can be adjusted by ratio of 180° from 1
second to 10 seconds, lengthen in anticlockwise direction, shorten in clockwise
direction.
5.3 Calling Volume Setting
The default calling volume is in middle value. There is an adjustable potentiometer on
the back side of the outdoor station(②), unlock time can be adjusted by ratio of 180°.
Users can freely adjust the calling volume according to the installation environment.
5.4 Address Setting
In standby mode, long press any button from outdoor station for 3 seconds, the device
will beep-beep to enter the address setting mode. Short press the button to add address
number from 1-5, after each short press, the device will beep different tmes to show
what number it is with.
For example: a device with NO. 1 will beep once, if it’s set to NO. 5, it will beep 5 times

10
after short press. When a device is already NO. 5, one short press more will make this
device become device NO. 1, cyclically.
After address setting, long press any button for 3 seconds to exit setting mode with a
long beep, or the setting mode will exit automatically if no operation for over 15
seconds.