GYM form Vibro Max User manual

GYMFORM ® Vibro Max Manual
Congratulations! You have bought the most advanced home vibration machine. In no time at all you will be
toned and in perfect shape. Always consult the instructions and please retain for future use.
Set includes –
1 x Gymform® Vibro Max unit. 1 x Pedometer with Radio
1 x Instruction and Construction guide. 1 x Advanced Workout Guide
1 x Structured Diet Plan 1 x Tape Measure
Advantages
Increases the basal metabolic rate, thereby burning calories.
Increases strength and body tone.
Helps improve circulation.
Reduces the appearance of cellulite.
Recommended for people with osteoporosis and osteoarthritis because it does not put pressure on joints.
Improves exibility.
Helps strengthen muscles.
Vibration training favours the development of lean muscle tissue.
Helps improve basic muscles.
Favours lymphatic drainage and improved circulation considerably helps reduce fat
Safety warnings –
Always read the instruction manual before operating the GYMFORM ® Vibro Max.
If you have any worry over your tness level or have experienced previous illness always consult your doctor
before using the GYMFORM ® Vibro Max.
If you have any respiratory dieses or asthma always consult your doctor before using the GYMFORM ®
Vibro Max.
Always place the GYMFORM ® Vibro Max on a at surface.
Do not let children operate the GYMFORM ® Vibro Max without an adults guidance.
Keep the GYMFORM ® Vibro Max away from water.
Do not use the GYMFORM ® Vibro Max with wet hands.
Turn off the power at the mains after use.
Not to be used by pregnant women.
Do not drink alcohol and use the machine.
Please drink water after use.
Maximum usage 4 times a day.
Machine features/operation
1 – 50 speeds.
5 specically designed programs.
3 Digital LED screens. One indicates the program number (“Program selection”), the second shows time
elapsed and Body Mass Index (BMI) (“time/BMI”) and the third shows the speed selected (“Speed”).
Screens:
1. PROGRAM SELECTION
2. TIME/BMI READY
3. SPEED
Please see attached graph for osculation’s per minute and seconds.
Buttons:
ON/STOP
START
PROGRAM SELECT
CONFIRM
UP
DOWN
English

Constructing the Gymform® Vibro Max
Before starting please lay out all of the parts listed below. Additional to the components below you will also
need some cello tape.
Equipment List
- Tools:
- Equipment
Tool A Tool B
No 1 = 1 x main unit No 2 = 1 x wire No 3 = 1 x Main Suport Tube
No 4 = 4 x Screws No 5 = 4 x Washers
No 8 = 4 x washers No 9 = 4 x BMI suport bars
No 10 = 2 x big screws
No 6 = 2 x Bottom suport bars No 7 = 4 x screws
No 11 = 4 x small screws
No 12 = 1 x control panel No 13 = 3 x control panel screws
No 14 = 1 x plug.

English
Please consult the equipment list.
Make sure the machine is in the O position (OFF).
1 - Lay the main unit (Nº1) on an even surface
2 - Take wire Nº 2 and pass it down the middle of the suport tube Nº 3. Please pay attention to have the larger
connector at the top. With some cello tape (not supplied) tape the larger connector of the wire Nº 2 onto the
main suport tube Nº 3. Please see the photo below
3 - When you assemble the main suport tube, make sure the wires remain connected.
4 - Connect the bottom connector of wire Nº 2 with the wire in the main unit. Please see the photo. Make
sure the wires remain connected.
5 - Now slot the main suport tube Nº 3 into the main unit Nº 1.
- Please see photo below
6 - Take screws Nº 4 and washers Nº 5 and put together.

7 - Please use tool A. At the bottom of the main suport tube Nº 3 use the screws Nº 4 and washers Nº 5 to
attach the main suport tube Nº 3 and the main unit Nº 1.
The photograph below shows how the main suport tube should look like when connected and assembled.
8 - Now take the 2 bottom suport bars no 6 and place into the main unit no 1 Please make sure the top of the
bottom suport bars no 6 are angled away from the main unit.
9 - Now take screws no 7 and washers no 8 and put together.
10 - Take tool B and use screws 7 and washers 8 to secure the bottom suport bars 6 to the main unit 1. This
should be done at the bottom of the main unit no 1.
Take the BMI suport bars Nº 9 and place on top of the bottom suport bars Nº 6. Pay attention that the top
bars of the BMI suport bars Nº 9 t into the main suport tube Nº 3.
11 - Please use the Tool B and take the big screws Nº 10 and secure the BMI suport bars Nº 9 to the main
suport unit.
- PHOTO NOTE – Please pay attention to keep all of the 3 wires outside of the suport tube Nº 3.
12 - Next please use tool B and the small screws Nº 11 to secure the BMI suport bars Nº 9 to the bottom
suport bars Nº 6.