H3C LSPM1FAN User manual

H3C LSPM1FAN and LSPM1FANB
Installation Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6W100-20111031

Copyright © 2011, Hangzhou H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior
written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care,
, TOP G, , IRF, NetPilot, Neocean, NeoVTL,
SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V2G, VnG, PSPT,
XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,
Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage,
use, and disposal of this product must meet the applicable national laws and regulations.

Conventions
This section describes the conventions used in this documentation set.
Convention Description
WARNING An alert that calls attention to important information that if not understood or followed can
result in personal injury.
CAUTION An alert that calls attention to important information that if not understood or followed can
result in data loss, data corruption, or damage to hardware or software.
IMPORTANT An alert that calls attention to essential information.
NOTE An alert that contains additional or supplementary information.
TIP An alert that provides helpful information.
Obtaining documentation
You can access the most up-to-date H3C product documentation on the World Wide Web at
http://www.h3c.com.
Click the links on the top navigation bar to obtain different categories of product documentation:
[Technical Support & Documents > Technical Documents] – Provides hardware installation, software
upgrading, and software feature configuration and maintenance documentation.
[Products & Solutions] – Provides information about products and technologies, as well as solutions.
[Technical Support & Documents > Software Download] – Provides the documentation released with the
software version.
Technical support
[e-mail]
http://www.h3c.com
Documentation feedback
You can e-mail your comments about product documentation to [email protected].
We appreciate your comments.

i
Contents
Fan trays overview······················································································································································· 1
LSPM1FAN fan tray ··························································································································································1
Overview···································································································································································1
Specifications····························································································································································1
LSPM1FANB fan tray························································································································································2
Overview···································································································································································2
Specifications····························································································································································2
Installing and removing a fan tray······························································································································ 4
Safety guidelines ·······························································································································································4
Tools required····································································································································································4
Installing a fan tray ···························································································································································4
Removing a fan tray ·························································································································································5

1
Fan trays overview
LSPM1FAN fan tray
Overview
The LSPM1FAN fan tray blows cool air from the power module side to the network port side. It comprises
two separate fans. The LSPM1FAN features small size, fast heat dissipation, and hot swapping. It can
automatically adjust the fan speed, providing powerful heat dissipation for the device.
Figure 1 LSPM1FAN fan tray
1
2
3
(1) Captive screw (2) Airflow direction label
(3) Fan tray handle
Specifications
Table 1 LSPM1FAN specifications
Item Specifications
Fans Two 40 × 40 × 28 mm (1.57 × 1.57 × 1.10 in) fans
Airflow direction Fans blow air from the power module side to the
network port side
Max fan speed 18500 R.P.M
Max airflow 45 CFM
Max power consumption 19.5 W
Voltage 12 V

2
Item Specifications
Operating temperature –10°C to 70°C (14°F to 158°F)
Relative humidity 5% to 95% (non condensing)
Storage temperature –40°C to 75°C (–40°F to 167°F)
Relative humidity 5% to 95% (non condensing)
LSPM1FANB fan tray
Overview
The LSPM1FANB fan tray draws in hot air from the network port side to the power module side. It
comprises two separate fans. The LSPM1FANB features small size, fast heat dissipation, and hot
swapping. It can automatically adjust the fan speed, providing powerful heat dissipation for the device.
Figure 2 LSPM1FANB fan tray
2
1
3
(1) Captive screw (2) Airflow direction label
(3) Fan tray handle
Specifications
Table 2 LSPM1FANB specifications
Item Specifications
Fans Two 40 × 40 × 28 mm (1.57 × 1.57 × 1.10 in) fans
Airflow direction Fans draw in air from the network port side to the
power module side
Max fan speed 18500 R.P.M
Max airflow 45 CFM

3
Item Specifications
Max power consumption 19.5 W
Voltage 12 V
Operating temperature –10°C to 70°C (14°F to 158°F)
Relative humidity 5% to 95% (non condensing)
Storage temperature –40°C to 75°C (–40°F to 167°F)
Relative humidity 5% to 95% (non condensing)

4
Installing and removing a fan tray
The installation and removal procedures for the LSPM1FAN and LSPM1FANB are similar. For more
information, see “Installing a fan tray”and “Removing a fan tray.”
Safety guidelines
To avoid fan tray and device damage, and bodily injury, note the following guidelines when installing or
removing a fan tray:
•Wear an ESD-preventive wrist strap, and make sure the wrist strap makes good skin contact.
•Do not touch any wire or connector on a fan tray.
•Do not place a fan tray on a moist area, and avoid liquid flowing into the fan tray.
•Do not remove any component on a fan tray. If a failure occurs on the internal wires or units, contact
the technical stuff to troubleshoot the problem.
Tools required
Prepare the following tools when installing and removing a fan tray:
•Phillips screwdriver
•ESD-preventive wrist strap
Installing a fan tray
TIP:
Before installing a fan tray, make sure the air flow of the fan tray is as required.
Step1 Wear an ESD-preventive wrist strap and make sure it makes good skin contact and is well grounded.
Step2 Take the fan tray from the package and check that the fan tray model is as required.
Step3 Face the slot into which the fan tray is to be installed. Grasp the handle of the fan tray with one hand and
support the fan tray bottom with the other, and then slide the fan tray along the guide rails into the slot
until the fan tray seats into the slot and has a firm contact with the connector on the backplane (see
callout 1 in Figure 3).
Step4 Fasten the captive screws on the fan tray with a Philips screwdriver until the fan tray is fixed into the
chassis (see callout 2 in Figure 3).

5
Figure 3 Install a fan tray
(1) Slide the fan tray into the slot (2) Fasten the captive screws
CAUTION:
•To prevent damage to the fan tray or the connector on the backplane, insert the fan tray
g
ently. If you
encounter a hard resistance while inserting the fan tray, pull out the fan tray and then insert it again.
•If the captive screws cannot be tightly fixed, check the installation of the fan tray.
Removing a fan tray
CAUTION:
•When replacing a fan tray with the device running, note safety with electricity.
•Do not touch rotating fans when replacing a fan tray with the device running.
Step1 Wear an ESD-preventive wrist strap and make sure it makes good skin contact and is well grounded.
Step2 Face the fan tray to be removed from the device. Loosen the captive screws on the fan tray with a Philips
screwdriver until the captive screws fall off the device, as shown in callout 1 in Figure 4.
Step3 Grasping the handle of the fan tray with one hand, pull the fan tray part way out the slot. Supporting the
fan tray bottom with the other hand, pull the fan tray slowly along the guide rails out of the slot, as shown
in callout 2 in Figure 4.
Step4 Put the removed fan tray on an anti-static mat or in its original package.
Figure 4 Remove a fan tray
2
1
1
(1) Loosen the captive screws on the fan tray (2) Pull the fan tray out of the slot

6
CAUTION:
•When removing a fan tray, take out the fan tray after the fans stop rotating.
•Do not touch the fans even if the fans stop rotatin
g
to avoid affectin
g
the fan balance, which can cause
greater fan operation noise.
•To ensure normal operation of the device, install a new fan tray within two minutes after the fan tray is
removed if you replace a fan tray with the device running.