H3C LSWM116Q User manual

1
H3C LSWM116Q interface card
user manual-6PW104
▌Introduction
Overview
The LSWM116Q interface card provides 16 QSFP+ ports.
Figure 1 Front panel
(1) QSFP+ port LED (2) QSFP+ port
QSFP+ ports
Table 1 and Table 2 describe QSFP+ transceiver modules and Table 3
describes QSFP+ cables available for the QSFP+ ports on the card.
Table 1 QSFP+ transceiver modules available for the QSFP+
ports (1)
QSFP+ transceiver
module
Central wavelength
(nm) Connector
QSFP-40G-SR4-M
M850 850 MPO (PC polished,
12-fiber)
QSFP-40G-CSR4-
MM850 850 MPO (PC polished, 12-fiber)
QSFP-40G-LR4-PS
M1310 1310 MPO (APC polished,
12-fiber)
QSFP-40G-BIDI-SR
-MM850 850 LC

2
QSFP+ transceiver
module
Central wavelength
(nm) Connector
QSFP-40G-LR4-W
DM1300
Four lanes:
•1271
•1291
•1311
•1331
LC
QSFP-40G-LR4L-W
DM1300
Four lanes:
•1271
•1291
•1311
•1331
LC
Table 2 QSFP+ transceiver modules available for the QSFP+
ports (2)
QSFP+
transceiver
module
Cable/fiber
diameter
(µm)
Modal
bandwidth
(MHz × km)
Max
transmission
distance
QSFP-40G-SR4
-MM850
Multi-mode,
50/125
2000 100 m (328.08 ft)
4700 150 m (492.12 ft)
QSFP-40G-CS
R4-MM850
Multi-mode,
50/125
2000 300 m (984.25 ft)
4700 400 m (1312.33
ft)
QSFP-40G-LR4
-PSM1310
Single-mode,
9/125 N/A 10 km (6.21 miles)
QSFP-40G-BIDI
-SR-MM850
Multi-mode,
50/125
2000 100 m (328.08 ft)
4700 150 m (492.12 ft)
QSFP-40G-LR4
-WDM1300
Single-mode,
9/125 N/A 10 km (6.21 miles)

3
QSFP+
transceiver
module
Cable/fiber
diameter
(µm)
Modal
bandwidth
(MHz × km)
Max
transmission
distance
QSFP-40G-LR4
L-WDM1300
Single-mode,
9/125 N/A 2 km (1.24 miles)
Table 3 QSFP+ cables available for the QSFP+ ports
QSFP+ cable Cable length Data rate
QSFP+ copper cable
LSWM1QSTK0 1 m (3.28 ft)
40 Gbps
LSWM1QSTK1 3 m (9.84 ft)
LSWM1QSTK2 5 m (16.40 ft)
QSFP+ fiber cable
QSFP-40G-D-AOC-7M 7 m (22.97 ft)
40 Gbps
QSFP-40G-D-AOC-10M 10 m (32.81 ft)
QSFP-40G-D-AOC-20M 20 m (65.62 ft)
NOTE:
•As a best practice, use H3C transceiver modules and cables fo
r
the interface card.
•The transceiver module and cable types supported by an
interface card vary by device model. For more information, see
the installation guide or contact H3C Support or marketing staff.
For more information about H3C transceiver modules and cables, see
H3C Transceiver Modules User Guide at www.h3c.com.
LEDs
Table 4 describes QSFP+ port LEDs on the front panel.

4
Table 4 QSFP+ port LED description
LED status Description
Steady green
A transceiver module is installed in the port. The
port is operating at 40 Gbps, and a link is
present on the port.
Flashing green The port is sending or receiving data at 40 Gbps.
Off No transceiver module is installed in the port, or
no link is present on the port.
▌Installing and removing the card
CAUTION:
•Before you install or remove the card, wear an ESD wrist strap
and make sure the strap makes good skin contact and is
reliably grounded.
•To avoid device damage, do not use excessive force when you
install or remove the card.
•The LSWM116Q interface card is hot swappable. However, do
not install or remove it during the startup of the switch.
Installing the card
1. Remove the filler panel (if any) from the target slot.
Keep the removed filler panel secure for future use.
2. Unpack the interface card.
Figure 2 LSWM116Q interface card
(1) Ejector lever (2) Latch

5
3. Press the latch on the card to release the ejector lever.
4. As shown by callout 1 in Figure 3, insert the card slowly into the
slot along the guide rails.
5. Rotate inward the ejector lever as shown by callout 2 in Figure 3
until the latch locks the ejector lever in place.
Figure 3 Installing an LSWM116Q interface card
Removing the card
1. Prepare an anti-static bag.
2. Remove the cables from the card.
3. Press the latch to release the ejector lever
4. Rotate outward the ejector lever as shown by callout 1 in Figure 4.
5. Pull out the interface card slowly out of the interface card slot, as
shown by callout 2 in Figure 4.
6. Place the removed interface card in the anti-static bag.
7. If you are not to install a new card, install a filler panel in the slot to
prevent dust and ensure good ventilation in the device.

6
Figure 4 Removing an LSWM116Q interface card
Installing and removing QSFP+ transceiver modules
or cables
For information about installing and removing QSFP+ transceiver
modules and cables, see H3C Transceiver Modules and Network
Cables Installation Guide at www.h3c.com.
Verifying the installation
After the installation is complete, determine whether the card is
operating correctly.
If the card fails to operate correctly, perform the following steps:
1. Reinstall the card following the installation procedures described
in this document.
2. If the problem persists, contact H3C Support.
▌Technical support
New H3C Technologies Co., Ltd. provides customers with
comprehensive technical support and service. If you purchase the
products from the sales agent of New H3C Technologies Co., Ltd.,
please contact our sales agent or technical personnel.
Website: http://www.h3c.com
BOM: 3101A0KJ