H3C LSWM116FC User manual

H3C LSWM116FC
Interface Cards
User Manual
New H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6PW102-20201120

Copyright © 2018-2020, New H3C Technologies Co., Ltd.
and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form
or by any means without prior written consent of New H3C
Technologies Co., Ltd.
Trademarks
Except for the trademarks of New H3C Technologies Co., Ltd., any
trademarks that may be mentioned in this document are the property
of their respective owners.
Notice
The information in this document is subject to change without notice.
All contents in this document, including statements, information, and
recommendations, are believed to be accurate, but they are
presented without warranty of any kind, express or implied. H3C shall
not be liable for technical or editorial errors or omissions contained
herein.
Environmental protection
This product has been designed to comply with the environmental
protection requirements. The storage, use, and disposal of this
product must meet the applicable national laws and regulations.
Documentation feedback
You can e-mail your comments about product documentation to
[email protected]om.
We appreciate your comments

i
Contents
About the LSWM116FC interface card···············1
Important information································································1
Front panel ···············································································1
Ports··································································2
Important information································································2
SFP28 ports··············································································2
LEDs··································································7
Important information································································7
SFP28 port LEDs······································································7
Installing and removing an interface module······9
Installing an interface module ···················································9
Removing an interface module················································ 10
Installing and removing SFP and SFP+ transceiver modules and
SFP+ cables··········································································· 11
Verifying the installation··························································12

1
About the LSWM116FC interface
card
Important information
The LSWM116FC interface card is applicable to multiple H3C switch
models. For the interface card compatibility with switches, contact
H3C Support or marketing staff.
Front panel
The LSWM116FC interface module provides 16 SFP28 ports and
supports fibre channel (FC) transceiver modules of various data
rates.
Figure 1 Front panel
(1) SFP28 port LED
(2) SFP28 port
2
1

2
Ports
Important information
•As a best practice, use H3C transceiver modules and cables for
the interface cards.
•The transceiver module and cable types supported by the
LSWM116FC interface card vary by device model. For more
information, see the installation guide or hardware reference for
the device, or contact H3C Support or marketing staff.
•The restrictions and guidelines for using the LSWM116FC
interface card vary by device model. For more information, see
the installation guide or hardware reference for the device.
•For more information about H3C transceiver modules and cables,
see H3C Transceiver Modules User Guide at www.h3c.com.
SFP28 ports
You can install the following transceiver modules and cables in the
SFP28 ports on an LSWM116FC interface module.
•
SFP transceiver modules in Table 1 and Table 2.
•
SFP+ transceiver modules in Table 3 and Table 4.
•
SFP+ copper cables in Table 5.
•
SFP+ fiber cables in Table 6.
Table 1 SFP transceiver modules available for the SFP28 ports (1)
SFP transceiver
module Central wavelength (nm) Connector
SFP-GE-T N/A RJ-45
SFP-GE-SX-MM850-A 850 LC

3
SFP transceiver
module Central wavelength (nm) Connector
SFP-GE-LX-SM1310-A 1310 LC
SFP-GE-LH40-SM1310 1310 LC
SFP-GE-LH40-SM1550 1550 LC
SFP-GE-LH80-SM1550 1550 LC
Table 2 SFP transceiver modules available for the SFP28 ports (2)
SFP
transceiver
module
Cable/fiber
diameter
(µm)
Modal
bandwidth
(MHz × km)
Max
transmission
distance
SFP-GE-T Twisted pair N/A 100 m (328.08 ft)
SFP-GE-S
X-MM850-A
Multi-mode,
50/125 500 550 m (1804.46 ft)
400 500 m (1640.42 ft)
Multi-mode,
62.5/125 200 275 m (902.23 ft)
160 220 m (721.78 ft)
SFP-GE-LX
-SM1310-A
Single-mode,
9/125 N/A 10 km (6.21 miles)
Multi-mode,
50/125 500 or 400 550 m (1804.46 ft)
Multi-mode,
62.5/125 500 550 m (1804.46 ft)
SFP-GE-LH
40-SM1310 Single-mode, 9/125 N/A 40 km (24.86 miles)

4
SFP
transceiver
module
Cable/fiber
diameter
(µm)
Modal
bandwidth
(MHz × km)
Max
transmission
distance
SFP-GE-LH
40-SM1550 Single-mode, 9/125 N/A 40 km (24.86 miles)
SFP-GE-LH
80-SM1550 Single-mode, 9/125 N/A 80 km (49.71 miles)
Table 3 SFP+ transceiver modules available for the SFP28 ports
(1)
SFP+ transceiver module Central
wavelength (nm) Connector
SFP-XG-SX-MM850-A 850 LC
SFP-XG-LX-SM1310 1310 LC
SFP-FC-8G-SW-MM850 850 LC
SFP-FC-8G-LW-SM1310 1310 LC
SFP-FC-16G-SW-MM850 840 to 860 LC
SFP-FC-16G-LW-SM1310 1295 to 1325 LC

5
Table 4 SFP+ transceiver modules available for the SFP28 ports
(2)
SFP+
transceiver
module
Fiber
diameter
(µm)
Modal
bandwidth
(MHz ×
km)
Max
transmission
distance
SFP-XG-SX-
MM850-A
Multi-mode,
50/125
2000 300 m (984.25 ft)
500 82 m (269.03 ft)
400 66 m (216.54 ft)
Multi-mode,
62.5/125 200 33 m (108.27 ft)
160 26 m (85.30 ft)
SFP-XG-LX-
SM1310 Single-mode, 9/125 N/A 10 km (6.21 miles)
SFP-FC-8G-
SW-MM850
Multi-mode,
62.5/125 200 150 m (492.12 ft)
Multi-mode,
50/125 500 380 m (1246.72 ft)
2000 500 m (1640.42 ft)
SFP-FC-8G-
LW-SM1310 Single-mode, 9/125 N/A 10 km (6.21 miles)

6
SFP+
transceiver
module
Fiber
diameter
(µm)
Modal
bandwidth
(MHz ×
km)
Max
transmission
distance
SFP-FC-16
G-SW-MM8
50
Multi-mode,
62.5/125 200
70 m (229.66 ft)
21 m (68.90 ft)
15 m (49.21 ft)
Multi-mode,
50/125
500
150 m (492.13 ft)
50 m (164.04 ft)
35 m (114.83 ft)
2000
380 m (1246.72 ft)
150 m (492.13 ft)
100 m (328.08 ft)
4700
400 m (1312.34 ft)
190 m (623.36 ft)
125 m (410.10 ft)
SFP-FC-16
G-LW-SM13
10
Single-mode,
9/125 N/A 10 km (6.21 miles)

7
Table 5 SFP+ copper cables available for the SFP28 ports
SFP+ copper cable Cable length Data rate
LSWM1STK 0.65 m (2.13 ft)
10.31 Gbps
LSWM2STK 1.2 m (3.94 ft)
LSWM3STK 3 m (9.84 ft)
LSTM1STK 5 m (16.40 ft)
Table 6 SFP+ fiber cables available for the SFP28 ports
SFP+ fiber cable Cable length Data rate
SFP-XG-D-AOC-7M 7 m (22.97 ft)
10.31 Gbps
SFP-XG-D-AOC-10M 10 m (32.81 ft)
SFP-XG-D-AOC-20M 20 m (65.62 ft)
LEDs
Important information
The indications of the LEDs on the LSWM116FC interface card vary
by device model. For more information, see the installation guide or
hardware reference for the device.
SFP28 port LEDs
Table 7 describes SFP28 port LEDs.

8
Table 7 SFP28 port LED description
LED status Description
On A transceiver module is installed in the port
and a link is present on the port.
Flashing The port is sending or receiving data.
Off No transceiver module is installed in the
port, or no link is present on the port.

9
Installing and removing an interface
module
CAUTION:
•
Before you install or remove an interface module, wear an
ESD wrist strap and make sure the strap makes good skin
contact and is reliably grounded.
•
To avoid device damage, do not use excessive force when
you install or remove an interface module.
Installing an interface module
Before you install an interface module, remove the filler panel (if any)
from the target slot. Keep the removed filler panel secure for future use.
To install an interface module:
1. Unpack the interface module.
Figure 2 LSWM116FC interface module
(1) Ejector lever
(2) Latch
12

10
2. Press the latch on the interface module to release the ejector
lever.
3. As shown by callout 1 in Figure 3, insert the interface module
slowly into the slot along the guide rails.
4. Rotate inward the ejector lever as shown by callout 2 in Figure 3
until the latch locks the ejector lever in place.
Figure 3 Installing an LSWM116FC interface module
Removing an interface module
CAUTION:
•
Before you remove an interface module, remove the cable
from it to avoid cable damage.
•
After removing an interface module, if no new interface
module is to be installed, install the filler panel as soon as
possible to prevent dust and ensure good ventilation in the
device.
1
2

11
To remove an interface module:
1. Prepare an anti-static bag.
2. Press the latch to release the ejector lever
3. Rotate outward the ejector lever as shown by callout 1 in Figure
4.
4. Pull out the interface module slowly out of the interface module
slot, as shown by callout 2 in Figure 4.
5. Place the removed interface module in the anti-static bag.
Figure 4 Removing an LSWM116FC interface module
Installing and removing SFP and SFP+
transceiver modules and SFP+ cables
For information about installing and removing SFP/SFP+ transceiver
modules and SFP+ cables, see H3C Transceiver Modules and
Network Cables Installation Guide at www.h3c.com.hk.
1
2

12
Verifying the installation
After the installation is complete, identify whether the interface
module is operating correctly.
If the interface module fails to operate correctly, perform the following
steps:
1. Reinstall it following the installation procedures described in this
document.
2. If the problem persists, contact H3C Support.