hager EG 103 Installation instructions

User instruction GB
EG 103, EG 103B
1 channel electronic
time switch
weekly cycle
Keys:
➀menu : selection of operating mode
auto : mode of running according to the
program selected.
prog : new for programming mode.
prog : modif to modify an existing
program.
: checking of the program.
: modification of time, date and
selection of the winter / summer time
change mode .
➁+and -: navigation or setting of values.
-: in auto, mode, selection of overrides,
or waivers.
➂ok : to validate flashing information
on display.
➃: to return to the previous step.
You may return into auto mode at any moment
using menu.
If no action is taken for 1 min, the switch
returns into auto mode.
Technical specifications
Electrical characteristics
●Supply voltage: 230 V AC ± 15%
●Frequency 50/60 Hz
●Power consumption : max. 0,5 VA à50 Hz
●Output: 1 changeover volt free contacts
●Maximum load:
AC1 µ16A 250 V~
DC1 µ4A 12 V
Cos φ= 0,6 µ10A 250 V~
Incandescent lighting 2300 W
Halogen lighting 230 V 2300 W
Compensated fluorescent tubes //
(max. 45 µF) 400 W
Non compensated fluorescent tubes,
compensated in series 1000 W
Compact fluorescent lamps 500 W
●Minimum current.
AC1 100 mA 250 V~
DC1 100 mA 12 V
●Galvanic insulation between power supply and
output = 4 kV
Functional characteristics
●Programming capacity: 56 pas
●Minimum time between 2 steps: 1 minute
●Running accuracy: ± 1,5 sec / 24h
●Operating reserve: lithium battery provides
5 years of backup.
●The product is set into standby state
(display switched-off) after 1 minute with
power off.
It switches back into auto mode as soon as
power is back or when pressing any key.
●Protection degree: IP 20
Environment
●Operating temperature: -5 °C to +45 °C
●Storage temperature: -20 °C to +70 °C
Connection
●Flexible capacity: 1 to 6 mm2
●Rigid capacity: 1,5 to 10 mm2
Connection diagram:
Major characteristics
●Product delivered with current time and date set.
●Automatic change of winter / summer time .
●Programming key .
- for permanent waivers,
- for program copy or save.
●Programming for day or group of days.
●56 program steps On, Off.
●Permanent overrides On or Off ( permanent light on).
●Temporary overrides On or Off ( flashing).
●Display bar graph of daily profile.
●Keyboard locking possible .
●Programmable with power off.
Reset:
●Program reset:
the program may be completely cleared by simultaneously pressing the 3 following keys:
menu, ok, . The time and the date will be kept.
●Total:
pressing simultaneously the -, +, ok, menu, keys lets you clear the entire contents of the
product.
Following a total reset it is necessary to reset the time and day of the device.
6E 6301.a
ok menu
+
auto prog
modif
new
On
Off
24
1812
60
1
2
3
4
L
N
1357
2468
EG 005
électro S.A. - 132, bld d’Europe - BP 3 - F - 67215 Obernai cedex - Tél. [phone]

6E 6301.a
Programming: prog new
Programming may be done for each day or
for a group of days. In this case instructions are
common to several days.
Days: 1 = Monday, 2 = Tuesday, 3 = Wednesday...
7 = Sunday.
1. Select the prog mode using menu, then ok.
2. Select the day(s) using +ou -. Validate with ok.
3. ok flashes. Use ok to validate the group.
4. Using +or -, select the state of the instruction:
On, Off.
5. Enter the time of switch-on using +or -.
Validate with ok.
6. Enter minutes with +ou -. Validate with ok.
Program the other instructions of the group of
days by repeating operations 3 to 7.
The day or the group of days may be modified at
the during step 3 by pressing the +,-ou .
At the end of programming return to auto mode
using the menu button.
In this mode it is also possible to add an instruction to
the program set up.
Proceed as described above.
prog
new
On
24
1812
60
ok
To check the daily profile set up without the risk of
modification or deletion:
Select the mode using menu and press ok.
The first step of Monday is displayed as well as
the daily profile.
Two options available for display:
1. Pressing repeatedly +ou - : lets you shift days.
In this case only the first daily step is displayed
as well as the daily profile.
2. Pressing ok: all steps of each day appear one
after the other.
Display
Select the prog mode with menu and press ok.
Select the modif mode with +or -.
Validate with ok.
The number of remaining program steps appears
for a short time.
The first step of the first day or group of days
appears.
Repeatedly pressing the ok key displays all
programmed steps one at a time.
Any flashing field (state, hour, minutes) may be
modified using +ou -, then validated with ok.
When the cursor is positioned on ok located
behind the group of days, you may display
successively the days or the groups of days and
switch directly to the one that has to be modified
using +or -.
To remove a program step:
select the state of the channel (One, Off or ),
press simultaneously +and -.
Clear appears on the screen. Validate with ok.
Modification or clearing of a program step:
prog modif
Pressing repeatedly -.
If the state of the output is On:
1st pressure: temporary waiver. Off and
flash. The next program step will
let you return to the automatic
mode.
2nd pressure: permanent override. On and
are permanent. This override
must be cancelled manually.
3rd pressure: permanent override. Off and
are permanent. This override
must be cancelled manually.
4th pressure: return to the automatic mode.
Override
Select the mode with menu then ok.
Modify the day, month, year, the hour and the
minutes using +or - and ok.
The time switch next suggests the winter / summer
time changes .
Select the type of change desired using +or -.
Validate with ok.
Setting time and day
Winter / summer time change
The type of change depends on the geographical
zone.
Types available:
The change always takes place between 2:00 and
3:00 a.m.
When the USER type is selected:
1. Enter the day then the month of the date of change
of the summer time (+ 1hour) with +or -and ok.
2. Enter the day then the month of the date of change
of the winter time (- 1hour) with +or -and ok.
The time switch will check which days of which
weeks correspond to these dates and will apply
changes to the same periods for the following years
independently of the date.
Type Start of time Start of time Zone
change Summer change Winter of application
Euro Last Sunday Last Sunday European Union
of March of October
USA First Sunday Last Sunday North America
of April of October
GB Last Sunday Fourth Sunday Only for the
of March of October United Kingdom
USER Date freely Date freely
programmed programmed
No No No
change change
As soon as the key appears on the switch
appear on the screen.
Two types of operation:
A. Permanent override:
Insert the key into the switch.
After 10 seconds the program contained in the
key will be executed without clearing the program
contained in the time switch.
As soon as the key is removed the program of
the time switch is again valid.
B. Copy (load) / Save (save):
The key makes it possible to save a program
contained in the time switch.
It is also possible to copy the contents of
the key into the clock.
1. Insert the key and wait for 2 sec.
2. Using menu select the mode:
save to save a program contained in the time
switch,
load to load the program of the key into the
time switch,
to check the program contained in the key.
3. Validate the selection with ok.
4. For save and load reconfirm with ok.
The following error messages may appear
on the screen:
no prog: the key is empty, it does not contain any
program.
Error: the key is that of a one-channel switch.
In these two cases:
●Only the save save is possible.
●The error message remains on display as long as
the key is present, but in this case the program of
the time switch is executed.
Key
To prevent all undesirable actions, the
keyboard of the time switch may be locked
using a key EG 004.
Unlocking is done in the same way.
Locking
*
*type according defect
A warranty period of 24 months is offered on hager products,
from date of manufacture, relating to any material or manu-
facturing defect. If any product is found to be defective it must
be returned via the installer and supplier (wholesaler).
The warranty is withdrawn if :
- after inspection by hager quality control dept the device is
found to have been installed in a manner which is contrary
to IEE wiring regulations and accepted practice within the
industry at the time of installation.
- the procedure for the return of goods has not been followed.
Explanation of defect must be included when returning goods.
Waranty GB
Hager 10.01