HALDER EH 22352 Quick guide

TRANSLATION OF THE
ORIGINAL OPERATING INSTRUCTIONS
threaded lifting pins
Keep for f t re se!

Erwin Halder KG
Erwin-Halder-Straße 5-9
88480 Achstetten-Bronnen
Phone [phone]
Fax [phone]
Email [email protected]
Internet www.halder.de
Designation: threaded lifting pins
Article group: 22 52 / 2B 52,
22 5 / 2B 5
Year of manufacture: 2021
Version of the
original operating
instructions:
01
Date of issue of original
operating instructions:
27.05.2021
Prod ct changes
Year Type Changes
Revisions to the doc ment
Date Version Changes
27.05.2021 01 First draft
Approvals
This document requires the following approvals:
Name Title
© 2021 by Erwin Halder KG
These original operating instructions and all illustrations contained in them are protected by
copyright. Any use outside the limits of copyright law without the prior written consent of the
publisher is prohibited and liable to prosecution. This applies especially to duplications,
translations, microfilming, storage and processing in electronic systems. For permission requests,
please contact the publisher.

3
Content
Content .............................................................................................................................................. - 3 -
List of fig res .................................................................................................................................... - 6 -
1 Introd ction ...................................................................................................................................... 7
1.1 Method of presentation ............................................................................................................ 9
1.1.1 Warnings pertaining to sections ................................................................................. 9
1.1.2 Embedded warnings ................................................................................................. 10
1.1. Other methods of presentation ................................................................................. 10
1.1.4 Symbols used in the original operating instructions ................................................. 10
1.2 Warranty and liability .............................................................................................................. 12
1. Copyright ................................................................................................................................ 1
1.4 Warranty conditions ............................................................................................................... 1
1.5 Service / Customer service .................................................................................................... 1
2 Safety ............................................................................................................................................... 14
2.1 Intended use .......................................................................................................................... 14
2.1.1 Structural changes to the threaded lifting pins ......................................................... 16
2.1.2 Foreseeable misuse ................................................................................................. 17
2.2 Staff requirements .................................................................................................................. 18
2.2.1 Responsibilities ......................................................................................................... 18
2.2.2 Obligation of the staff ................................................................................................ 18
2.2. Unauthorised persons .............................................................................................. 19
2.2.4 Instruction ................................................................................................................. 19
2. General safety instructions .................................................................................................... 20
2.4 Safety measures for environmental protection ...................................................................... 20
2.5 Special danger warnings / residual dangers .......................................................................... 21
2.5.1 Symbols used on the lifting accessoryn ................................................................... 21
2.5.2 Dangers due to falling loads ..................................................................................... 21
2.5. Dangers from hot surfaces ....................................................................................... 21
2.5.4 Dangers due to incorrect use ................................................................................... 22
2.5.5 Crushing hazards...................................................................................................... 22
2.5.6 Dangers due to suspended loads ............................................................................. 2
2.5.7 Dangers due to improper storage ............................................................................. 2
2.5.8 Dangers due to the use of incorrect spare parts ...................................................... 2
2.5.9 Crushing and cutting hazards for hands ................................................................... 24
2.5.10 Dangers for unauthorised persons ........................................................................... 24
2.5.11 Dangers due to insufficient qualification ................................................................... 24
2.5.12 Dangers when the lifting accessory are used by multiple persons .......................... 25
2.5.1 Hazards due to contamination .................................................................................. 25
2.5.14 Dangers due to damaged threaded lifting pins ......................................................... 25
2.5.15 Hazards due to cleaning liquids (containing solvents) and other chemical
substances or emissions .......................................................................................... 26
2.6 Personal protective equipment .............................................................................................. 26
2.7 Notices for emergencies ........................................................................................................ 27
2.8 Obligation of the operator ...................................................................................................... 28

Content
4
3 Description of the threaded lifting pins ...................................................................................... 29
.1 Overview ............................................................................................................................... 29
.1.1 Overview of functional elements - EH 22 52 / EH 2B 52 ....................................... 29
.1.2 Overview of functional elements - EH 22 5 / EH 2B 5 ....................................... 0
.1. Type plate overview / inscription .............................................................................. 1
.2 Functional description ........................................................................................................... 2
.2.1 Materials................................................................................................................... 4
. Technical data ....................................................................................................................... 5
. .1 Threaded lifting pins, self-locking - EH 22 52 ......................................................... 5
. .2 Threaded lifting pins, self-locking - EH 2B 52 ......................................................... 6
. . Threaded lifting pins, self-locking, for centre holes according to DIN 2 - EH 22 52 7
. .4 Threaded lifting pins, self-locking, with rotatable shackle - EH 22 5 .................... 8
. .5 Threaded lifting pins, self-locking, with rotatable shackle - EH 2B 5 .................... 9
. .6 Ambient conditions ................................................................................................... 40
. .7 Intended service life ................................................................................................. 40
4 Transport and storage .................................................................................................................. 41
4.1 Controls at the time of acquisition by the recipient ............................................................... 41
4.2 Packaging .............................................................................................................................. 41
4.2.1 Unpacking ................................................................................................................ 42
4.2.2 Re-packaging ........................................................................................................... 42
4. Notes on hazards during transport ........................................................................................ 42
4.4 Permitted aids for transport ................................................................................................... 4
4.5 Scope of delivery ................................................................................................................... 4
4.6 Interim storage ...................................................................................................................... 4
5 Assembly ........................................................................................................................................ 44
5.1 Notes on hazards during assembly ....................................................................................... 44
5.2 Preparatory measures ........................................................................................................... 44
5. Choice of location of use ....................................................................................................... 44
5. .1 Necessary operating and maintenance areas ......................................................... 44
5. .2 Requirements for the location of use ....................................................................... 45
6 Commissioning .............................................................................................................................. 46
6.1 Safety measures before commissioning ............................................................................... 46
7 Operation ........................................................................................................................................ 47
7.1 Safety measures during normal operation ............................................................................ 47
7.2 Example application .............................................................................................................. 47
8 Malf nctions .................................................................................................................................. 50
8.1 Malfunctions and corrective measures .................................................................................. 50
9 Maintenance ................................................................................................................................... 51
9.1 Safety measures during maintenance work .......................................................................... 51
9.2 Inspection and maintenance work ......................................................................................... 52
9.2.1 Maintenance intervals .............................................................................................. 52
9.2.2 Maintenance - daily .................................................................................................. 52
9.2. Maintenance - weekly .............................................................................................. 5
9.2.4 Maintenance - annual .............................................................................................. 5

Content
5
10 Dismantling and disposal .............................................................................................................. 54
10.1 Disassembly ........................................................................................................................... 55
10.2 Disposal ................................................................................................................................. 56
11 Annex .............................................................................................................................................. 57
11.1 EC Declaration of Conformity ................................................................................................ 57

6
List of fig res
Fig re 1: Overview of f nctional elements - EH 22352 / EH 2B352 ............................................... 29
Fig re 2: Overview of f nctional elements - EH 22353 / EH 2B353 ............................................... 30
Fig re 3: Type plate overview / inscription ...................................................................................... 31
Fig re 4: Installation examples - threaded lifting pins, self-locking ............................................. 33
Fig re 5: Installation examples - threaded lifting pins, self-locking, for centre holes according
to DIN 332 ....................................................................................................................................... 33
Fig re 6: Installation examples - threaded lifting pins, self-locking, with rotatable shackle ..... 34
Fig re 7: Materials .............................................................................................................................. 34
Fig re 8: Dimensioned drawing - threaded lifting pins, self-locking - EH 22352 ......................... 35
Fig re 9: Dimensioned drawing - threaded lifting pins, self-locking - EH 2B352 ........................ 36
Fig re 10: Dimensional Drawing - threaded lifting pins, self-locking, for centre holes according
to DIN 332 ....................................................................................................................................... 37
Fig re 11: Dimensioned drawing - threaded lifting pins, self-locking, with rotatable shackle -
EH 22353 ......................................................................................................................................... 38
Fig re 12: Dimensioned drawing - threaded lifting pins, self-locking, with rotatable shackle -
EH 2B353 ........................................................................................................................................ 39
Fig re 13: Examples of symbols on packaging .............................................................................. 41
Fig re 14: Example application - Inserting ...................................................................................... 48
Fig re 15: Example application - Withdrawing ................................................................................ 49

7
1 Introd ction
These original operating instructions provide you with all the information you need for the
smooth operation of the threaded lifting pins (hereinafter also referred to as lifting
accessory).
The original operating instructions must be read, understood and applied by all persons
assigned to the operation, maintenance, cleaning and troubleshooting of the lifting
accessory. This applies in particular to the listed safety instructions.
After studying the original operating instructions you can
– use the threaded lifting pins in a safe manner,
– maintain the threaded lifting pins according to regulations,
– clean the threaded lifting pins according to regulations,
– and take the appropriate action when a malfunction occurs.
In addition to the original operating instructions, general, statutory and other binding
regulations on accident prevention and environmental protection of the country of use
must be observed.
The original operating instructions must always be kept at the place of use of the
threaded lifting pins.
These original operating instructions are valid for the following product groups and article
numbers:
Threaded lifting pins, self-locking (article gro p 22352)
Heat-treated steel, tempered, manganese-
phosphated
Stainless steel 1.4542, precipitation-
hardened
22 52.0008 22 52.1008
22 52.0010 22 52.1010
22 52.0012 22 52.1012
22 52.0014 -
22 52.0016 22 52.1016
22 52.0020 22 52.1020
22 52.0024 22 52.1024
22 52.0027 -
22 52.00 0 -

1 Introd ction
1.1 Method of presentation
8
Threaded lifting pins, self-locking, for centre holes according to DIN 332 (article gro p
22352)
Heat-treated steel, tempered, manganese-
phosphated
Stainless steel 1.4542, precipitation-
hardened
22 52.2008 22 52. 008
22 52.2010 22 52. 010
22 52.2012 22 52. 012
22 52.2014 -
22 52.2016 22 52. 016
22 52.2020 22 52. 020
22 52.2024 22 52. 024
Threaded lifting pins, self-locking, with rotatable shackle (article gro p 22353)
Heat-treated steel, tempered, manganese-
phosphated
Stainless steel 1.4542, precipitation-
hardened
22 5 .0008 22 5 .1008
22 5 .0010 22 5 .1010
22 5 .0012 22 5 .1012
22 5 .0016 22 5 .1016
22 5 .0020 22 5 .1020
22 5 .0024 22 5 .1024

1 Introd ction
1.1 Method of presentation
9
1.1 Method of presentation
Texts in these original operating instructions that require special attention are marked as
follows as a notice and as a direct warning of dangers:
1.1.1 Warnings pertaining to sections
Warnings pertaining to sections apply not only to a specific action, but to all actions within
a section.
Str ct re
SIGNAL WORD
Symbol for
more
detailed
explanation
of the
danger
Nat re and so rce of the danger!
Possible consequence(s) in case of non-compliance!
– Measure(s) to avoid the danger.
Danger levels
DANGER
Hazard with a high degree of risk which, if not avoided, will result in death
or serious injury.
WARNING
Hazard with a medium degree of risk which, if not avoided, can result in
death or serious injury.
CAUTION
Low-risk hazard which, if not avoided, may result in minor or moderate
injury.
NOTICE
Hazard with a low degree of risk which, if not avoided, may result in
damage to property.

1 Introd ction
1.1 Method of presentation
10
1.1.2 Embedded warnings
Embedded warnings apply to specific actions and are directly integrated into the action.
Str ct re
SIGNAL WORD Type and source of danger
Possible consequences in case of non-compliance
– Measures to avoid the danger
Danger levels
– DANGER / WARNING / CAUTION (see 1.1.1 Warnings pertaining to
sections)
– NOTICE (without warning triangle, see 1.1.1 Warnings pertaining to sections)
1.1.3 Other methods of presentation
The info symbol provides useful information.
– Texts that follow this mark are lists.
 Texts that follow this mark describe activities that are to be carried out in the
specified order.
“” Texts in quotation marks are references to other chapters or sections.
1.1.4 Symbols sed in the original operating instr ctions
In warning notices, special dangers are additionally marked as follows:
Warning against hand inj ries
This symbol warns of hand injuries.
Warning against danger of c tting
This symbol warns of cutting dangers.
Hot s rface warning
This symbol warns of the danger of burns from hot surfaces.
Warning against s spended load
This symbol warns of dangers when standing under suspended loads.

1 Introd ction
1.1 Method of presentation
11
No trespassing by na thorised persons
This symbol prohibits unauthorised persons from entering the danger zone.
Dangers cannot be identified by unauthorised persons.
Observe original operating instr ctions
This symbol indicates that the original operating instructions must be
observed.
Recycling
This symbol stands for the return of various materials into recycling.
CE marking
The CE marking on the product is the manufacturer's declaration that the
product complies with the essential requirements of the relevant European
health, safety and environmental protection legislation.

1 Introd ction
1.2 Warranty and liability
12
1.2 Warranty and liability
The obligations agreed in the supply contract, the general terms and conditions as well as
the terms of delivery of the threaded lifting pins and the legal regulations valid at the time
of the conclusion of the contract apply.
All information and notices in these original operating instructions have been compiled
taking into account the applicable standards and regulations, the state of the art and our
many years of knowledge and experience.
These original operating instructions are not intended to be, and should not be used as a
substitute means of determining the suitability or reliability of the threaded lifting pins for
any particular user application. It is the duty of the manufacturer or distributor to carry out
an adequate and complete risk assessment, and evaluation and testing of the threaded
lifting pins with regard to the respective specific application or use in question.
Warranty and liability claims for personal injury and damage to property are excluded if
they are attributable to one or more of the following causes:
– improper or inappropriate use of the threaded lifting pins,
– improper assembly, commissioning, operation, servicing and cleaning of the threaded
lifting pins,
– use of the threaded lifting pins with defective components or improperly installed or
non-functional components,
– a failure to observe the original operating instructions and the notices in the original
operating instructions regarding assembly, commissioning, operation, servicing and
cleaning of the threaded lifting pins,
– use of unqualified or untrained personnel,
– structural changes to the threaded lifting pins (Conversions or other changes to the
lifting accessory may not be made without the prior written consent of Erwin Halder
KG. In case of infringement, the threaded lifting pins lose their EC conformity),
– improperly performed repairs,
– use of non-approved spare parts or use of spare parts that do not meet the technically
specified requirements,
– disasters, effects of foreign bodies, and force majeure.
Furthermore, Erwin Halder KG reserves the right to revise this publication at any time if
technical changes are made in the course of improvements to usage properties and
further development, without obligation to notify any person of the revisions.

1 Introd ction
1.3 Copyright
13
1.3 Copyright
These original operating instructions are protected by copyright and intended for internal
use only.
Transfer of the original operating instructions to third parties, reproduction in any form and
in any manner – even in extracts – as well as exploitation and/or communication of the
contents are not permitted without the written consent of Erwin Halder KG, except for
internal purposes.
Contraventions obligate to compensation for damages. We reserve the right to make
further claims.
1.4 Warranty conditions
The warranty conditions are contained in the general terms and conditions of Erwin
Halder KG.
1.5 Service / C stomer service
For technical information, our customer service is at your disposal:
Phone: [phone]
In addition, our employees are always interested in new information and
experience which is derived from use and can be valuable for the improvement of
our products.

14
2 Safety
WARNING
A fail re to observe the following safety instr ctions can have
serio s conseq ences:
Danger to persons due to mechanical or chemical influences or failure of
important lifting accessory functions!
– Please read the safety and danger information in this section thoroughly
before putting the threaded lifting pins into operation.
– In addition to the instructions in these original operating instructions,
observe the generally applicable safety and accident prevention
regulations.
– In addition to the instructions in these original operating instructions,
observe the existing national occupational, operating and safety
regulations. Also comply with existing internal factory regulations.
2.1 Intended se
The operational safety of the threaded lifting pins is only guaranteed if they are used as
intended.
The threaded lifting pins are not suitable for rotating the load. It should be noted that the
version with a rotating shackle optimally aligns in the direction of force. Damaged
threaded lifting pins can endanger lives. Before each se the threaded lifting pins must
be inspected for visible defects (e.g. deformations, fractures, cracks, damage, missing
threaded elements, corrosion, function of the release).
The threaded lifting pins must be completely inserted into a thread that is true to gauge
and rest fully on the bearing surface (on the 0° bevel for threaded lifting pins for centre
holes according to DIN 2). When inserting threaded lifting pins, the rotation of the load
must be prevented. Contamination (e.g. grinding sludge, oil and emission deposits, dust,
chips, etc.) can impair the function of the threaded lifting pins. Damaged threaded lifting
pins must be immediately withdrawn from further use. To release the threaded elements,
press in the push element (A). The threaded elements are locked again by releasing the
push element (A).
Attention: The push element (A) is locked when it is sprung back to its original position
by the spring force. The push element must not be actuated under load! Before
operation, the threaded lifting pins must be checked for the possibility of accidental or
unintentional actuation of the push element to release the threaded lifting pins. Any
accidental or unintentional release of the push element during operation of the threaded
lifting pins must be ruled out by the operator / user.
The intended standard method of use of threaded lifting pins is operation by one person,
and they may only be operated by instructed specialist personnel. The threaded lifting
pins may only be used within the scope of their technical data. The specified maximums

2 Safety
2.1 Intended se
15
in the technological data must not be exceeded. The load values F1, F2 and F apply to
lifting in a steel receptacle. The field of application of threaded lifting pins is in the
industrial sector. The threaded lifting pins are not intended for different modes of
operation, as it is a manual tool. threaded lifting pins are not intended for any other use
than the use listed here; other uses would be considered improper use. In particular, it is
prohibited
– to mark the threaded lifting pins subsequently in colour (especially in red), to avoid
confusion with high-strength anchor points,
– to exceed the maximum load of the threaded lifting pins (see " . Technical data"),
– to use the threaded lifting pins after exceeding the maximum permissible load cycles
(see " . Technical data"). After exceeding the maximum permissible load cycles (see
" . Technical data"), the threaded lifting pins must be permanently taken out of
operation,
– to use the threaded lifting pins as a protective device or safety function,
– to use the threaded lifting pins as a pulling element,
– not to produce the installation sketch according to the specifications of the company
Erwin Halder KG,
– to use defective or unsuitable accessories,
– to operate the threaded lifting pins if the functional components are deactivated,
manipulated or defective,
– to operate the threaded lifting pins while untrained persons are in the danger zone,
– to operate the threaded lifting pins if they are not ready for operation or have been
modified,
– to operate the threaded lifting pins without instruction.
– to use the threaded lifting pins only inserted, without using locking,
– to use the threaded lifting pins for constantly rotating loads,
– to use the threaded lifting pins for lifting, holding or carrying persons,
– to actuate the locking push element under load,
– to place objects on the threaded lifting pins. Remove all objects that are on the
threaded lifting pins.

2 Safety
2.1 Intended se
16
Proper use also includes
– the observance of all notices in the original operating instructions and the third-party
documentation,
– noting that in case of an overhead or horizontal use, the load must be secured against
falling down before opening the threaded lifting pins,
– compliance with the inspection and servicing intervals,
– the use of operating and auxiliary materials in accordance with applicable safety
regulations,
– compliance with the operating conditions,
– inspecting the threaded lifting pins for visible defects or damage before each use.
The technical specifications given in the technical data must be observed without
exception.
Only use the threaded lifting pins for their intended purpose, otherwise safe
operation is not guaranteed.
For all personal injury and damage to property resulting from improper use, the
operator of the threaded lifting pins and not the manufacturer is responsible!
In relation to the minimum breaking load, threaded lifting pins have specified load
capacities per threaded lifting pins. They must not be added together for multiple-strand
lifting accessories. For such applications, the relevant rules must be observed. The load
values F1 / F2 / F apply to lifting in a steel receptacle.
For alternating use on different objects to be transported, such as large tools, threaded
lifting pins with the next largest thread diameter must be used. When using multi-strand
slings, the relevant rules must be observed.
The load capacity specifications are only valid if
– the threaded lifting pins are fully screwed in with sufficient thread depth,
– the full surface of the threaded lifting pins lies flat on the bearing surface,
– the forces that are introduced can be absorbed by the base material without
deformations affecting safety,
– the blind holes are drilled deep enough for the bearing surface to rest on.
The load capacity applies up to max. 90° angle of inclination.
In the case of through holes, a nut should be completely and firmly fitted or screwed on
from the opposite side. If the thread length of the threaded lifting pins is sufficient, the use
of a washer is also recommended.
2.1.1 Str ct ral changes to the threaded lifting pins
Design and manufacturer's acceptance are based on the Product Safety Act (ProdSG).
No changes, additions or conversions may be made to the threaded lifting pins without
the prior written consent of Erwin Halder KG.

2 Safety
2.1 Intended se
17
In case of non-compliance, the threaded lifting pins lose their EC conformity. With this,
the manufacturer of the threaded lifting pins is outside of the warranty.
Immediately replace components that are not in problem-free condition.
Only use original spare parts / wear parts / accessories. These parts are specially
designed for the threaded lifting pins. For parts purchased from third parties it cannot be
guaranteed that they have been designed and manufactured to meet the requirements on
stress and safety.
Parts and optional equipment not supplied by Erwin Halder KG are not approved for use
on the threaded lifting pins.
2.1.2 Foreseeable mis se
Any use of the threaded lifting pins beyond the intended use, and/or other use, can lead
to serious injuries.
– Do not use the threaded lifting pins in case of lack of maintenance or inspection.
– Never use the threaded lifting pins without the locking.
– Do not use the threaded lifting pins with constantly rotating loads.
– Do not use the threaded lifting pins to lift, hold or carry people.
– Avoid jerky loads.
– Never use the threaded lifting pins in a nut thread that is not true to gauge,
– Never use the threaded lifting pins if they are not fully inserted into the nut thread;
thread flanks can be on top of each other when inserted - push element does not
come out and threaded pin does not lock.
– Overload or misuse can lead to failure of the lifting equipment. Load can fall.

2 Safety
2.2 Staff req irements
18
2.2 Staff req irements
The threaded lifting pins may only be transported, installed, operated, maintained,
repaired, commissioned and decommissioned, inspected or disposed of by persons who
are qualified and / or instructed to do so. These persons must know the original operating
instructions and act accordingly. The respective powers of the staff should be clearly
defined.
The following qualifications for various fields of activity are specified in the original
operating instructions:
Personnel to be trained
Personnel to be trained, such as an apprentice or a temporary worker, are not aware of
all the dangers that can occur when operating the threaded lifting pins. They may only
perform work on the threaded lifting pins under the supervision of qualified or instructed
personnel.
Instr cted personnel
Instructed personnel have been instructed by the operator or by qualified personnel about
the tasks assigned to them and possible dangers in case of improper behaviour.
Q alified personnel
Due to their technical training, knowledge and experience as well as knowledge of the
relevant regulations, qualified personnel are able to carry out the work assigned to them
and to independently recognise and avoid possible dangers.
2.2.1 Responsibilities
Improper handling can lead to considerable personal injury and damage to property.
Therefore, have all activities carried out only by personnel qualified for them.
– Only persons who can be expected to carry out their work reliably are permitted as
personnel. No persons may work on the threaded lifting pins if their ability to react is
impaired by drugs, alcohol, medication or similar.
– All persons working on the threaded lifting pins must read the original operating
instructions and confirm that they have understood them by signing them.
– Personnel to be trained may initially only work on the threaded lifting pins under the
supervision of qualified personnel. The completed and successful instruction must be
confirmed in writing.
The operator is responsible for instructing the personnel.
2.2.2 Obligation of the staff
Before starting work, all persons charged with working on the threaded lifting pins
undertake
– to observe the basic regulations on work safety and accident prevention,

2 Safety
2.2 Staff req irements
19
– to read the safety instructions and warnings in these original operating instructions
and confirm by signature that they have understood them.
2.2.3 Una thorised persons
Unauthorised persons who do not meet the qualification requirements for the personnel
are not aware of the dangers in the work area.
– Keep unauthorised persons away from the work area.
– If in doubt, speak to such persons and instruct them to leave the work area.
– Interrupt work as long as unauthorised persons are in the work area.
2.2.4 Instr ction
The personnel must be instructed regularly by the operator. Record the execution of the
instruction to better keep track.
Date Name Type of
instr ction
Instr ction given
by Signat re

2 Safety
2.3 General safety instr ctions
20
2.3 General safety instr ctions
– The threaded lifting pins may be put into operation and serviced only after these
original operating instructions have been taken notice of.
– Only use the threaded lifting pins for their intended purpose (see “2.1 Intended use“).
– Do not release the threaded lifting pins if there are other people in the danger zone
(under a suspended load, for example).
– When operating the threaded lifting pins, refrain from any kind of work that could
impair the safety of persons or the threaded lifting pins.
– Never operate the threaded lifting pins with defective components. Never put built-in
safety features out of operation.
– Always keep the work area of the threaded lifting pins clean and tidy to avoid danger
from dirt and parts lying around.
– Do not exceed the technical performance data (see " . Technical data").
– Keep all safety and danger warnings on the threaded lifting pins in a legible condition
and renew them as necessary.
– Operation and work on the threaded lifting pins may only be carried out by qualified or
instructed personnel (see “2.2 Staff requirements“).
– In case of malfunctions, stop using the threaded lifting pins immediately. Have faults
rectified by appropriately trained specialists or by Erwin Halder KG .
– Always keep the original operating instructions at the place the threaded lifting pins is
used. It must be ensured that all persons who carry out activities on or with the
threaded lifting pins can read the original operating instructions at any time.
2.4 Safety meas res for environmental protection
During all work, comply with the regulations on waste avoidance and proper waste
recycling or disposal.
Particularly during assembly and maintenance work as well as during decommissioning,
care must be taken to ensure that groundwater-polluting substances such as cleaning
liquids (containing solvents) and other chemical substances or emissions do not pollute
the ground or enter the sewer system. These substances must be collected in suitable
containers, and stored, transported and disposed of in accordance with national
regulations.