HAMPTON BAY 52-SKV User manual

Item #1000 022 652, 1000 019 369
Model #42010, 99913
UL Model #52-SKV
USE AND CARE GUIDE
FLOWE 52 IN. CEILING FAN
Questions, problems, missing parts? Before returning to the store call
Hampton Bay Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-877-527-0313
HAMPTONBAY.COM
THANK YOU
We appreciate the trust and condence you have placed in Hampton Bay through the purchase of this ceiling fan. We strive to continually create
quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Hampton Bay!

2
Table of Contents ................................................................2
Safety Information...............................................................2
Warranty ...............................................................................3
Pre-Installation ....................................................................3
Installation............................................................................6
Assembly..............................................................................7
Operation ...........................................................................14
Care and Cleaning.............................................................15
Troubleshooting.................................................................15
1. To reduce the risk of electric shock, ensure the electricity has
been turned off at the circuit breaker or fuse box before you
begin.
2. All wiring must be in accordance with the National Electrical
Code ANSI/NFPA 70-1999 and local electrical codes. Electrical
installation should be performed by a qualified licensed
electrician.
3. The outlet box and support structure must be securely mounted
and capable of reliably supporting 35 lbs. (15.9 kg). Use only UL
Listed outlet boxes marked “Acceptable for Fan Support of 35
lbs. (15.9 kg) or less.”
4. The fan must be mounted with a minimum of 7 ft (2 m) clearance
from the trailing edge of the blades to the oor.
5. Do not operate the reversing switch while the fan blades are
in motion. You must turn the fan off and stop the blades before
you reverse the blade direction.
6. Do not place objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other items,
use caution when working around or cleaning the fan.
8. Electrical diagrams are for reference only. Light kits that are
not packed with the fan must be UL-listed and marked suitable
for use with the model fan you are installing. Switches must be
UL General Use Switches. Refer to the instructions packaged
with the light kits and switches for proper assembly.
9. After making electrical connections, spliced conductors should
be turned upward and pushed carefully up into the outlet box.
The wires should be spread apart with the grounded conductor
and the equipment-grounding conductor on one side of the
outlet box.
10. All setscrews must be checked and retightened where
necessary before installation.
WARNING: To reduce the risk of personal injury, do
not bend the blade brackets (also referred to as
anges) during assembly or after installation. Do
not insert objects in the path of the blades.
WARNING: Remove the rubber motor stops on the
bottom of the fan before installing the blades or
testing the motor.
WARNING: To reduce the risk of re or electric
shock, do not use this fan with any solid-state
speed control device.
WARNING: To avoid possible electrical shock, turn
the electricity off at the main fuse box before
wiring. If you feel you do not have enough electrical
wiring knowledge or experience, contact a licensed
electrician.
WARNING: Electrical diagrams are for reference
only. Optional use of any light kit shall be UL-listed
and marked suitable for use with this fan.
WARNING: To reduce the risk of re or electric
shock, this fan should only be used with fan speed
control part no. UC7067RYA, manufactured by Rhine
Electronic Co.,LTD or control part no. FAN28R-240W,
manufactured by Chia Wei Electric Co.,LTD.
Safety Information
Table of Contents
WARNING: To reduce the risk of re, electric shock
or personal injury, mount to outlet box marked
“Acceptable for fan support of 35 lbs. (15.9 Kg) or
less,” and use screws provided with the outlet box.

3HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Pre-Installation
Warranty
The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a life-
time after the date of purchase by the original purchaser. The supplier also warrants that all other fan parts, excluding any glass or acrylic blades,
to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase
by the original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or superior model if the
product is returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstall-
ing the product are your responsibility. Damage to any part, such as by accident, misuse, improper installation, or by afxing any accessories, is
not covered by this warranty. Because of varying climatic conditions this warranty does not cover any changes in brass nish, including rusting,
pitting, corroding, tarnishing, or peeling. Brass nishes of this type give their longest useful life when protected from varying weather conditions.
A certain amount of “wobble” is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the
warranty invalid. There is no other express warranty. Hampton Bay hereby disclaims any and all warranties, including but not limited to those
of merchantability and tness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be
disclaimed is limited to the time period as specied in the express warranty. Some states do not allow a limitation on how long an implied war-
ranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental, consequential, or special damages arising
out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of
incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specic legal rights, and you
may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product
as part of a claim on the warranty must be paid by the customer.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HamptonBay.com.
SPECIFICATIONS
TOOLS REQUIRED
Size Speed Volts Amps Watts RPM CFM Net
Weight
Gross
Weight Cube Feet
52 in.
Low
Medium
High
120
0.24
0.34
0.51
11.8
24.9
57.1
70
105
160
2764
3903
5701
19.8 lbs.
(9 kg)
22.5 lbs.
(10.2 kg) 1.88
NOTE: These are approximate measures. They do not
include the Amps and Wattage used by the light kit.
Phillips
screwdriver
Flat blade
screwdriver
Adjustable
wrench
Electrical
tape
Wire
cutter
Step ladder

4
Part Description Quantity
AA Plastic wire connector 3
BB Hanger pin 1
CC Locking pin 1
DD Extra blade bracket screw 1
Part Description Quantity
EE Extra lock washer 1
FF Rubber gasket 1
GG Plastic plug 1
Pre-Installation (continued)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
AA BB CC
FF GG
DD
EE

5HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Part Description Quantity
A Slide-on mounting bracket
(inside canopy)
1
B Ball/downrod assembly 1
C Canopy with canopy ring attached 1
D Decorative motor collar cover 1
E Fan-motor assembly 1
Part Description Quantity
F Light kit tter assembly 1
G Blade 5
H Blade bracket 5
I Glass bowl 1
J Remote control (battery included) 1
K Receiver 1
L CFL Light bulb, 14-Watt maximum 3
IMPORTANT: This product and/or components are
governed by one or more of the following U.S. Patents:
5,947,436; 5,988,580; 6,010,110; 6,046,416, 6,210,117
and other patents pending.
Pre-Installation (continued)
PACKAGE CONTENTS
A
B
C
D
E
H
F
J
I
G
L
K
TM

6
Installation
MOUNTING OPTIONS
WARNING: To reduce the risk of re, electric shock or personal
injury, mount to an outlet box marked “Acceptable for fan
support of 35 lbs. (15.9 Kg) or less,” and use the screws
provided with the outlet box. An outlet box commonly used for
the support of lighting xtures may not be acceptable for fan
support and may need to be replaced. If in doubt, consult a
qualied electrician.
If your ceiling fan does not have an existing UL-listed mounting
box, then install one using the following instructions:
□Disconnect the power by removing the fuses or turning off
the circuit breakers.
□Secure the outlet box directly to the building structure. Use
the appropriate fasteners and materials. The outlet box and
its bracing must be able to fully support the weight of the
moving fan (at least 35 lbs.). Do not use a plastic outlet box.
The illustrations below show three different ways to mount the
outlet box.
If the canopy touches the downrod, then remove the decorative canopy
bottom cover and turn the canopy 180° before attaching the canopy to
the mounting plate.
To hang your fan where there is an existing xture but no ceiling joist,
you may need an installation hanger bar as shown above
(available at any Home Depot store).
NOTE: You may need a longer downrod to maintain proper
blade clearance when installing on a steep, sloped ceiling. The
maximum angle allowable is 30° away from horizontal.
Outlet Box
Outlet Box
Recessed
Outlet
Box
Provide Strong
Support
Ceiling
Mounting
Plate
Outlet Box
Hanger Bar

7HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Assembly - Standard Ceiling Mount
Routing the wires
Assembling the fan
Preparing for mounting
□Loosen, but do not remove, the setscrew (TT) on the collar
(O) on top of the fan-motor assembly (E).
□Align the holes at the bottom of the downrod (B) with the
holes in the collar (O) on top of the fan-motor assembly (E).
□Carefully insert the hanger pin (BB) through the holes in the
collar (O) and downrod (B). Be careful not to jam the hanger
pin (BB) against the wiring inside the downrod (B).
□Insert the locking pin (CC) through the hole near the end of
the hanger pin (BB) until it snaps into its locked position.
□Re-tighten the setscrew (TT) on the collar (O) on top of the
fan-motor assembly (E).
□Remove the canopy ring (M) from the canopy (C) by turning
the ring to the right until it unlocks.
□Remove the mounting bracket (A) from the canopy by
loosening the four canopy screws (HH) on the top of the
canopy (C).
□Remove the two non-slotted canopy screws (HH) and loosen
the slotted canopy screws (HH). This will enable you to
remove the mounting bracket (A).
□Route the wires exiting the top of the fan-motor assem-
bly (E) into the decorative motor collar cover (D) and
through the canopy ring (M).
□Make sure the slot openings are on top and route the
wires through the canopy (C) and then through the ball/
downrod assembly (B).
2
3
1
C
M
A
HH
E
D
C
B
M
D
E
C
B
B
BB
CC
O
TT
WARNING: Failure to properly install the locking pin could
result in the fan becoming loose and possibly falling.

8
Assembly - Close-To-Ceiling Mount
Assembly - Hanging the Fan
□Remove three of the six screws and lock washers (PP)
(every other one) securing the motor collar to the top of the
fan-motor assembly (E).
□Place the rubber gasket (FF) over the remaining three
screws, route the wires exiting the top of the fan-motor
assembly (E) through the canopy ring (make sure the slot
opening are on top), then proceed to place the ceiling
canopy (C) over the collar at the top of the motor.
□Align the mounting holes with the holes in the motor and
fasten, using the three screws and lock-washers (PP) re-
moved previously. Tighten the mounting screws securely.
E
FF
C
PP
Attaching the fan to the electrical
box Hanging the fan
□Pass the 120-Volt supply wires through the center hole in the
mounting bracket (A).
□Install the slide-on mounting bracket (A) on the outlet box by
sliding the slide-on mounting bracket (A) over the two screws (1)
provided with the outlet box. If necessary, use leveling washers
(not included) between the slide-on mounting bracket (A) and
the outlet box. The at side of the slide-on mounting bracket (A)
should face toward the outlet box, as shown.
□Securely tighten the two mounting screws (1).
□Carefully lift the fan-motor assembly (E) up to the slide-on
mounting bracket (A).
□Seat the hanger ball portion of the ball/downrod assembly (B)
in the slide-on mounting bracket (A) socket. Ensure that the tab
on the slide-on mounting bracket (A) socket is properly seated
in the groove in the hanger ball. If using close-to-ceiling
mounting, hang the fan on the hook provided by utilizing one
of the holes at the outer rim of the ceiling canopy (C).
1 2
WARNING: To reduce the risk of re, electric shock
or personal injury, mount to an outlet box marked
“Acceptable for fan support of 35 lbs. (15.9 Kg) or less,”
and use the screws provided with the outlet box.
A
1
1
WARNING: The hook is only to balance the fan while making
the electrical connections. Failure to hang as shown may
result in the hook breaking, causing the fan to fall. The hook
must pass from the inside to the outside of the canopy.
A
C C
E
A
B
E
Routing the wiresPreparing for mounting 21□Remove canopy ring (M) from the canopy (C) by turning the
ring to the right until it unlocks.
□Remove the mounting bracket (A) from the canopy (C) by
loosening the four canopy screws (HH) on the top of the
canopy (C). Remove the two non-slotted canopy screws (HH)
and loosen the slotted canopy screws (HH).
□Remove the decorative canopy bottom cover (N) from the
canopy (C) by depressing the three studs.
C
M
N
A
HH

9HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Operating Your Fan and Remote Control (continued)
43
NOTE: The frequencies on your receiver and remote
control have been preset at the factory. Before installing
the receiver, make sure the dip switches on the receiver
and remote control are set to the same frequency. The dip
switches on the remote control are located inside the battery
compartment.
NOTE: The battery will weaken with age and should be
replaced before leaking takes place as this will damage the
remote control. Dispose of used battery properly and keep
the battery out of the reach of children.
Setting the code on the remote
control and receiver Installing the receiver
□Remove the remote control (J) battery cover by pressing
rmly on the arrow and sliding the cover off.
□Slide the code switches to your choice of either up or down.
The factory setting is up.
□Slide the code switches on the receiver (K) to the same
position as set on the remote control (J).
□Replace the battery cover on the remote control (J).
□Position the supply wires to the left side of the slide-on
mounting bracket (A); position the fan wires to the right
side. Partially insert the receiver (K) (at side up) until one
end rests on the ball/downrod assembly (B).
WARNING: To reduce the risk of re or electric shock,
remember to disconnect power. The electrical wiring must
meet all local and national electrical code requirements.
The electrical source and fan must be 110/120 volt, 60Hz.
Do not use this product in conjunction with any variable wall
control. Incorrect wire connection can damage this receiver.
CAUTION: If other fan wires are a different color, have this
unit installed by a licensed electrician.
CAUTION: Do not install in a damp location or immerse
in water (For indoor use only). Do not pull on or cut leads
shorter. Do not drop or bump the unit.
A
C
B
K
NOTE: The switch marked ON/DIM controls the dimming
function of the lights: If using CFL bulbs, use a ballpoint pen
or small screwdriver to set the switch to ON to disable the
dimming function. If using standard bulbs, set the switch to
DIM to enable the dimming function.
1 2 34
ON
ON
DIM
12V 23A
DIP
1 2 3
ON
4
DIP
1 2 34
O N
ON
DIM
DIP
J
K

10
Making the electrical connection
□Connect the two green fan wires (II) to the household wire (II).
□Connect the fan motor white wire (LL) to the receiver (K) white
wire (LL) using a wire connector (AA).
□Connect the fan motor black wire (KK) to the receiver (K) black
wire (KK) using a wire connector (AA).
□Connect the fan motor blue wire (JJ) to the receiver (K) blue
wire (JJ) using a wire connector (AA).
□Connect the receiver (K) red or black wire (OO) to the supply
black (hot) wire (KK) using a wire connector (AA).
□Connect the receiver (K) white wire (LL) to the supply white
wire (neutral) (LL) wire using a wire connector (AA).
□Spread the wires apart so that the green (II) and white (LL)
wires are on the side of the outlet box (MM) and the black
wire (KK) is on the other side.
□Turn the wire connectors (AA) upward and push the wiring
into the outlet box (MM).
5
IMPORTANT: Use the wire connecting nuts supplied with your
fan. Secure the connectors with electrical tape and ensure there
are no loose strands or connections.
WARNING: Each wire not supplied with this fan is designed to
accept up to one 12-gauge house wire and two wires from the
fan. If you have larger than 12-gauge house wiring or more
than one house wire to connect to the fan wiring, consult an
electrician for the proper size wire nuts to use.
II
MM
K
OO
LL
LL
KK
JJ
KK
LL
NOTE: The fan comes with 54 in. lead wires for use with an
extended ball/downrod assembly. If using the 4.5 in. ball/downrod
assembly (B) provided, you can cut the lead wires to your desired
length (no shorter than 12 in.).
Assembly - Hanging the Fan (continued)

11 HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Assembly - Hanging the Fan (continued)
Mounting the fan-motor assembly
(standard mount)
Mounting the fan-motor assembly
(close-to-ceiling mount)
□Align the locking slots of the ceiling canopy (C) with the two
screws in the mounting bracket (A). Push up to engage the
slots and turn clockwise to lock in place.
□Firmly tighten the two mounting screws.
□Install the remaining two mounting screws into the holes in
the canopy (C) and tighten rmly.
□Install the decorative canopy ring (M) by aligning the ring’s
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock in place.
□Carefully unhook the fan from the mounting bracket (A) and
align the locking slots of the ceiling canopy (C) with the two
screws in the mounting bracket (A). Push up to engage the
slots and turn clockwise to lock in place. Immediately tighten
the two mounting screws rmly.
□Install the remaining two mounting screws into the holes in
the canopy (C) and tighten rmly.
□Install the decorative canopy ring (M) by aligning the ring’s
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock in place.
□You may now proceed to attaching the fan blades.
6
WARNING: When using the standard ball/downrod mounting, the
tab in the ring at the bottom of the mounting bracket must rest in
the groove of the hanger ball. Failure to properly seat the tab in
the groove could cause damage to the wiring.
A
C
E
M
WARNING: The locking slots of ceiling canopy are provided only
as an aid to mounting. Do not leave the fan assembly unattended
until all four canopy screws are engaged and rmly tightened.
A
C
E
M
7

12
Assembly - Attaching the Fan Blades
Attaching the blade brackets to
the motor Attaching the blades
1 2
□Fasten the blade bracket (H) to the motor (E) by inserting the
alignment post into the slot on the bottom of the fan-motor
assembly (E) and tightening the motor screws.
□Please note that the motor screws are pre-attached into
the blade bracket (H). Repeat for the remaining four blade
brackets (H).
□Mount the fan blades (G) to the blade bracket (H) by aligning
the three key-slot holes in the blade (G) with the three posts
on the top of the blade brackets (H).
□Hold the blade (G) with both hands close to the blade bracket
(H) and press the blade (G) down rmly. Ensure the key-slot
holes are properly seated on the blade arm posts.
□While still holding the blade (G) down with both hands, rmly
slide the blade (G) away from the fan-motor assembly (E) until
the blade (G) engages in the locking mechanism. Make sure
the steel locking mechanism at the rear of the blade bracket
(H) springs upward and butts against the edge of the blade (G)
indicating a secure connection.
□Visually inspect the top of the blade bracket (H) to ensure the
locking mechanism is securely in place.
□Repeat for the remaining blades (G).
H
G
E
H
NOTE: Your fan features revolutionary advancements for quick and
easy blade installation.
NOTE: Your fan blades are reversible. Select the blade side nish
which best accentuates your decor.

13 HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Assembly - Assembling the Fan Without the Light Kit
Attaching the light kit tter assembly Installing the bulbs and attaching
the glass bowl
12
□Remove the three light kit mounting screws (RR) on the black
bracket below the fan-motor assembly (E).
□Plug the molded adaptor plug from the light kit (F) to the
molded adaptor plug from the fan-motor assembly (E). Make
sure the connector latch close properly.
□Align the holes in the light kit (F) with the holes in the black
bracket below the fan-motor assembly (E) and install using
the light kit mounting screws (RR) that were removed in the
rst step above.
□Remove the rubber washer (P), hex nut (Q), bottom cover (R),
and nial (S) from the threaded nipple of the light kit tter
assembly (F).
□With power off, install the three CFL Light bulb, (14-Watt maxi-
mum included) (L) by screwing into the light bulb sockets.
□Position the glass bowl (I) over the threaded nipple.
□Re-install the rubber washer (P), hex nut (Q), and bottom cover
(R) to the threaded nipple to secure the glass shade properly.
□Re-install and tighten the nial (S).
CAUTION: To reduce the risk of electric shock, disconnect
the electrical supply circuit to the fan before installing the
light xture.
CAUTION: Do not over tighten the hex nut, overtightening the
hex nut may cause the glass to break.
NOTE: Notice the location of the fan’s slide switch. This is the
switch used to change the fan’s directional rotation. For more
information on the operation of this switch, see Operating
Your Fan on page 14.
E
F
RR
E
F
L
I
P
RQ
S
NOTE: This light kit cannot be transferred to another fan.
Assembly - Attaching the Lights
Assembling the fan without the
light kit
1□Remove the three light kit mounting screws (RR) on the black
bracket below the fan-motor assembly (E).
□In order to use the fan without the light kit, remove the switch
cup (2) from the top of the light kit tter assembly (F) by
removing the center hex nut inside the switch cup cover, and
then thread the switch cup cover off of the threaded nipple on
the top of the light kit tter assembly (F).
□Press the plastic plug (GG) (provided) into the center hole of
the switch cup (2).
□Position the switch cup (2) onto the black bracket and reinstall
the light kit mounting screws (RR).
E
GG
RR
2

14
USING THE REMOTE CONTROL
□Install the 12-Volt battery (included) into the battery
compartment of the remote control (J).
□Press the desired button on the remote control (J) to operate
the fan:
□“3” button: Press to set the fan speed to high.
□“2” button: Press to set the fan speed to medium.
□“1” button: Press to set the fan speed to low.
□Power button (UU): Press to turn the fan off.
□Light button (VV): Press and release immediately to turn
the light on or off. Press and hold to dim or brighten the
bulbs to the desired level and then release (the dimmer
function is for Tungsten bulbs only).
Your fan is equipped with a remote control to operate the fan speed
and lights of your new ceiling fan.
The speed setting for warm or cool weather depends on factors such
as the room size, ceiling height, number of fans and so on.
The fan is shipped from the factory with the reversing switch
positioned to circulate air downward. If airow is desired in the
opposite direction, turn your fan off and wait for the blades to stop
turning, then slide the reversing switch (located in switch cup) to the
opposite position, and turn the fan on again. The fan blades will turn in
the opposite direction and reverse airow.
Warm weather - (Forward) A downward airow creates a cooling effect.
This allows you to set your air conditioner on a higher setting without
affecting your comfort.
Cool weather - (Reverse) An upward airow moves warm air off of the
ceiling. This allows you to set your heating unit on a lower setting without
affecting your comfort.
NOTE: Wait for the fan to stop before reversing the direction of the
blade rotation.
NOTE: This remote is equipped with a 16-code combination. To
prevent possible interference from or to other remote units, such
as garage door openers, car alarms, or security systems, change
the combination code but be sure that the code on both the remote
control and receiver in the fan are the same.
UU
V V
OPERATING YOUR FAN
Operation

15 HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Troubleshooting
Problem Solution
The fan will not start. □Check the main and branch circuit fuses or breakers.
□Check the line wire connections to the fan and switch wire connections in the switch housing.
□Check the battery in the remote control.
□Ensure you are in the normal range of 10-20 ft.
□Ensure the dip switch settings are the same on the remote control and receiver.
□Remember to turn off the power supply before checking the dip switches settings.
The fan is noisy. □Ensure all motor housing screws are snug.
□Ensure the screws that attach the fan blade bracket to the motor hub are tight.
□Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.
□Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.
□If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light
bulbs are also secure.
□Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.
□Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.
The fan wobbles. □Check that all blade and blade arm screws are secure.
□Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the
ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the
ceiling. Measure this distance. Rotate the fan until the next blade is positioned for measurement. Repeat for each
blade. Any measurement deviation should be within 1/8 in. Run the fan for ten minutes. If the fan continues to
wobble please contact Customer Service and a balacing kit will be sent to you at no charge.
□Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade
attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
□Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage
the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the nish. The
plating is sealed with a lacquer to minimize discoloration or tarnishing.
□You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a
light application of shoe polish.
□You do not need to oil your fan. The motor has permanently lubricated sealed ball bearings.
WARNING: Make sure the power is off before cleaning
your fan.
Care and Cleaning

Questions, problems, missing parts? Before returning to the store call
Hampton Bay Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-877-527-0313
HAMPTONBAY.COM
Retain this manual for future use.
X0000000000-A

Artículo núm. 1000 022 652, 1000 019 369
Modelo núm. 42010, 99913
Modelo núm. 52-SKV
Aprobado por UL
GUÍA DE USO Y MANTENIMIENTO
VENTILADOR DE TECHO FLOWE, DE 1.32 M
¿Preguntas, problemas o piezas faltantes? Antes de regresar a la tienda,
llama al servicio al cliente de Hampton Bay,
de 8 a.m. a 6 p.m., hora estándar del Este, de lunes a viernes
al 1-877-527-0313
HAMPTONBAY.COM
GRACIAS
Apreciamos la conanza que has depositado en Hampton Bay al comprar este ventilador de techo. Nos esforzamos para continuamente crearproductos de calidad
diseñados para mejorar tu hogar. Visítanos por Internet para ver nuestra línea completa de productos disponibles para las necesidades de mejoras de tu hogar.
¡Gracias por elegir Hampton Bay!

2
Tabla de contenido ..............................................................2
Información de seguridad...................................................2
Garantía................................................................................3
Preinstalación ......................................................................3
Instalación............................................................................6
Ensamblaje........................................................................... 7
Funcionamiento.................................................................14
Mantenimiento y limpieza.................................................15
Solución de problemas .....................................................15
1. Para disminuir el riesgo de descarga eléctrica, asegúrate de
cortar la electricidad del cortacircuitos o la caja de fusibles
antes de comenzar.
2. Todo el cableado debe cumplir con el Código Nacional de
Electricidad ANSI/NFPA 70-1999 y con los códigos locales de
electricidad. La instalación eléctrica debe ser hecha por un
electricista certificado y calificado.
3. La caja eléctrica y estructura de soporte deben montarse de
forma segura y tener capacidad para sostener de manera
conable 15.9 kg. Usa solamente cajas eléctricas aprobadas por
UL marcadas como “Apropiada para sostener ventiladores de
15.9 kg o menos”.
4. El ventilador debe ir montado con un mínimo de 2.13 m de
separación entre el borde trasero de las aspas y el piso.
5. No muevas el interruptor de reversa mientras las aspas del
ventilador estén en movimiento. Debes apagar el ventilador y
detener las aspas antes de invertir la dirección de las mismas.
6. No coloques objetos en la trayectoria de las aspas.
7. Para evitar lesiones físicas o daños al ventilador y otros
artículos, ten cuidado al limpiar el ventilador o al trabajar cerca
de él.
8. Los diagramas eléctricos son sólo para referencia. Los kits
de luces no empaquetados con el ventilador deben estar
aprobados por UL y marcados como apropiados para ser
usados con el modelo de ventilador que estás instalando. Los
interruptores deberán estar clasicados por el UL como de uso
general. Consulta las instrucciones adjuntas a los kits de luces
e interruptores para obtener información sobre el ensamblaje
adecuado.
9. Después de concluir las conexiones eléctricas, debes voltear
los conductores empalmados hacia arriba y meterlos con
cuidado en la caja eléctrica. Los cables deben estar separados,
con el cable a tierra y el conductor a tierra del equipo en uno
de los lados de la caja eléctrica.
10. Todos los tornillos de fijación deben ser verificados y
ajustados donde sea necesario antes de la instalación.
ADVERTENCIA: Para reducir el riesgo de lesiones
personales, no dobles los soportes de las aspas
(también llamados bridas) durante el ensamblaje o
después de la instalación. No coloques objetos en
la trayectoria de las aspas.
ADVERTENCIA: Quita los tapones de goma del motor
en la parte inferior del ventilador antes de instalar
las aspas o de vericar el motor.
ADVERTENCIA: Para reducir el riesgo de incendio
o descarga eléctrica, no utilices este ventilador
con ningún dispositivo de control de velocidad de
estado sólido.
ADVERTENCIA: Para evitar una posible descarga
eléctrica, desconecta la electricidad de la caja de
fusibles principal antes de realizar el cableado.
Si crees que no tienes suciente conocimiento o
experiencia sobre cableado eléctrico, contacta a un
electricista certicado.
ADVERTENCIA: Los diagramas eléctricos son sólo
para referencia. Cualquier juego de luces opcional
debe estar aprobado por UL y marcado como
adecuado para ser usado con este ventilador.
ADVERTENCIA: Para disminuir el riesgo de incendio
o descarga eléctrica, este ventilador sólo debe ser
usado con un control de velocidad con el núm. de
pieza UC7067RYA, fabricado por Rhine Industrial
Co., LTD. o FAN28R-240W , fabricado por Chia Wei
Electric Co., LTD.
Información de seguridad
Tabla de contenido
ADVERTENCIA: Para reducir el riesgo de incendio,
descarga eléctrica o lesiones personales, instala
sólo en una caja eléctrica clasicada como
“apropiada para sostener ventiladores de 15.9 kg o
menos” y usa los tornillos que vienen con la misma.

3HAMPTONBAY.COM
Para obtener asistencia, llama al 1-877-527-0313.
Preinstalación
Garantía
El proveedor garantiza de por vida, a partir de la fecha en que el comprador original lo adquiere, que el motor del ventilador no presenta defectos
de fabricación ni de materiales al momento en que es enviado desde la fábrica. El proveedor también garantiza por un período de un año, a
partir de la fecha de compra por el comprador original, que todas las demás piezas del ventilador, sin incluir ningún aspa de vidrio o acrílico,
no presentarán ningún defecto de fabricación o de material en el momento de su salida de la fábrica. Acordamos reparar todos los defectos
del tipo antes mencionado, sin cargo alguno o, a nuestra discreción, reemplazar el producto por un modelo de igual calidad o superior si el
producto es devuelto. Para obtener servicio de garantía debe presentar una copia del recibo como comprobante de compra. Todos los costos de
retiro y reinstalación del producto son su responsabilidad. Los daños a cualquiera de las piezas como resultado de accidentes, uso inadecuado,
instalación inadecuada, o debidos a la instalación de cualquier accesorio, no están cubiertos bajo esta garantía. Debido a que las condiciones
climáticas pueden variar, esta garantía no cubre ningún cambio en el acabado en bronce, incluyendo óxido, perforación, corrosión, manchas
o descascaramiento. Los acabados en bronce de este tipo tienen una vida útil más prolongada cuando se les protege de las condiciones
climáticas cambiantes. Es normal cierta “oscilación” y no debe ser considerado como un defecto. Cualquier servicio técnico realizado por
personas no autorizadas anulará la garantía. No hay ninguna otra garantía expresa. Mediante la presente, Hampton Bay se exime de cualquier
garantía, incluyendo pero sin limitarse a aquellas de comercialización e idoneidad para un n particular, de acuerdo a lo contemplado por la
ley. La duración de cualquier garantía implícita que no se pueda eximir, está limitada al período de tiempo especicado en la garantía explícita.
Algunos estados no permiten una limitación en la duración de la garantía, por consiguiente la limitación anterior puede no aplicarse a su caso.
El minorista no será responsable por daños directos, indirectos o especiales que resulten o deriven del uso o rendimiento del producto excepto
en casos en que lo estipule la ley. Algunos estados no permiten la exclusión o limitación de daños directos o indirectos, por lo que la limitación
o exclusión anterior podría no aplicarse a su caso. Esta garantía le otorga derechos legales especícos, y es posible que también tenga otros
derechos que varían de un estado a otro. Esta garantía sustituye todas las garantías anteriores. Los costos de envío de cualquier devolución de
productos hecha como parte de una reclamación de garantía deben ser pagados por el cliente.
Comuníquese con el Equipo de Servicio al Cliente llamando al 1-877-527-0313 o visite www.HamptonBay.com.
ESPECIFICACIONES
HERRAMIENTAS NECESARIAS
Tamaño Velocidad Voltios Amperios Watts RPM CFM Peso
neto
Peso
bruto Pies cúbicos
1,32 m
Baja
Media
Alta
120
0,24
0,34
0,51
11,8
24,9
57,1
70
105
160
2764
3903
5701
19,8 lbs.
(9 kg)
22,5 lbs.
(10,2 kg) 1,88
NOTA: Estas medidas son aproximadas. No incluyen ni
el amperaje ni el vataje consumido por el kit de luces.
Destornillador
Phillips
Destornillador
plano
Llave
ajustable
Cinta de
electricista Cortacables
Escalera

4
Pieza Descripción Cantidad
AA Conector plástico para cables 3
BB Pasador de soporte 1
CC Pasador de cierre 1
DD Tornillo adicional para soporte de
aspas
1
Pieza Descripción Cantidad
EE Arandela de seguridad adicional 1
FF Junta de goma 1
GG Tapón plástico 1
Preinstalación (continuación)
HERRAJES INCLUIDOS
NOTA: No se muestra el tamaño real de los herrajes.
AA BB CC
FF GG
DD
EE