HAMPTON BAY Bentley II 328 478 User manual

328 478
Bentley II
13 in Ceiling Fan
Owner’s Manual
Bentley II
Ventilador de Techo de 33 cm
Manual del Propietario

Bentley II by Hampton Bay
®

Date Purchased
Store Purchased
Model No.
Serial No.
Vendor No.
UPC
Thank you for purchasing our ceiling fan. This product has been
manufactured with the highest standards of safety and quality.
Table of Contents
Safety Rules . . . . . . . . . . . . . . . . . . . . 1
Unpacking Your Fan . . . . . . . . . . . . . . 2
Installing Your Fan . . . . . . . . . . . . . . . 3
Operating Your Fan . . . . . . . . . 10
Care of Your Fan . . . . . . . . . . . . . . . . 11
Troubleshooting . . . . . . . . . . . . . . . . . 11
Specifications . . . . . . . . . . . . . . . . . . 12
Warranty Information . . . . . . . . . . . . 13
328-478
219032
792145356134
13” Bentley II
Ceiling Fan by Hampton Bay

Safety Rules - Read and Save These Instructions
1
To reduce the risk of electric shock, insure electricity has been turned off
at the circuit breaker or fuse box before beginning.
All wiring must be in accordance with the National Electrical Code
“ANSI/NFPA 70-1999” and local electrical codes. Electrical installation
should be performed by a qualified licensed electrician.
WARNING: To reduce the risk of electrical shock or fire, do not use this
fan with any solid-state fan speed control device. It will permanently
damage the electronic circuitry.
CAUTION: To reduce the risk of personal injury, use only the screws
provided with the outlet box.
The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 35 pounds. Use only ETL
Listed outlet boxes marked “FOR FAN SUPPORT”.
The fan must be mounted with a minimum of 10 feet clearance from the
trailing edge of the blades to the floor.
Avoid placing objects in path of the blades.
To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
Do not use water or detergents when cleaning the fan or fan blades. A dry
dust cloth or lightly dampened cloth will be suitable for most cleaning.
After making electrical connections, spliced conductors should be turned
upward and pushed carefully up into outlet box. The wires should be
spread apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box and ungrounded conductor on the
other side of the outlet box.
All set screws must be checked and retightened where necessary before
installation.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY. DO NOT INSERT
FOREIGN OBJECTS IN – BETWEEN ROTATING FAN BLADES.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET BOX.

2
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items:
4
2
3
Canopy assembly
Ball/downrod assembly
Coupling cover
Fan motor assembly
1.
2.
3.
4.
3-speed wall control with 2 mounting
screws and 4 wire nuts
Mounting plate with 2 mounting screws
5a.
5b.
WARNING
DO NOT INSTALL OR USE FAN IF ANY
PART IS DAMAGED OR MISSING.
CALL TOLL FREE 1-877-902-5588.
B
5a
5b
A
A.
B.
Electrical Hardware
(3 Plastic Wire Nuts)
Allen wrench
1

3
Installing Your Fan
Figures 1~2 are examples of different ways to
mount the outlet box.
If there isn't an existing ETL listed mounting box,
then read the following instructions. Disconnect
the power by removing fuses or turning off circuit
breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the fan
(at least 35 lbs). Do not use plastic outlet boxes.
Tools Required
Mounting Options
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN
ONLY TO AN OULET BOX MARKED ACCEPT-
ABLE FOR FAN SUPPORT AND USE THE
MOUNTING SCREWS PROVIDED WITH THE
OULET BOX. OUTLET BOX COMMONLY USED
FOR THE SUPPORT OF LIGHTING FIXTURE
MAY NOT BE ACCEPTABLE FOR FAN SUPPORT
AND MAY NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
Outlet Box
Outlet Box
Outlet Box
Figure 2
Figure 1
To hang your fan where there is an existing fixture
but no ceiling joist, you may need an installation
hanger bar as shown in Figure 4 (available at any
Home Depot store).
Figure 3
Phillips screwdriver, straight slot screwdriver, step
ladder and wire cutters.

4
Figure 5
Motor Wires
Ball/Downrod
Assembly
Ceiling Canopy
Canopy Bottom
Cover
Coupling Cover
Clevis Pin Cotter Pin
Set Screw
Allen wrench
Pin in Locked
Positioon
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly.
Hanging the Fan
Remove the decorative canopy bottom cover
from the canopy by turning the cover counter
clockwise. (Figure 4)
Remove the mounting bracket from the canopy
by removing the 1 of 2 screws from the bottom
of the mounting bracket and loosening the
other one a half turn from the screw head.
Next, turn the canopy counter clockwise to
removing the mounting bracket from the
canopy. (Figure 4)
Remove the clevis pin, cotter pin and set
screws from the top of the motor assembly, you
need to use the allen wrench to loosen your set
screws. (Figure 5)
NOTE: If a longer downrod is needed, take out
the screw located in the hanger ball, lower the
hanger ball and remove the pin, remove all 3
pieces from the downrod and assemble them
onto the new longer downrod before
proceeding step 4. (The longer downrod is
available at any Home Depot store)
Route wires exiting from the top of the fan
motor through the coupling cover, canopy
cover, canopy and then through the ball/
downrod. (Figure 5)
1.
2.
3.
4.
WARNING
FAILURE TO PROPERLY INSTALL COTTER PIN
AS NOTED IN STEP 5 COULD RESULT IN FAN
LOOSENING AND POSSIBLY FALLING.
Tighten two set screws at top of the fan motor
collar by allen wrench. (Fig. 5)
6.
Align the holes at the bottom of the downrod
with the holes in the coupling on top of the
motor housing (Figure 5). Carefully insert the
clevis pin through the holes in the collar and
downrod. Be careful not to jam the clevis pin
against the wiring inside the downrod. Insert
the cotter pin through the hole near the end of
the clevis pin until it snaps into its locked
position, as noted in the circle inset of Fig. 5.
5.
Figure 4
Ceiling
Mounting
Bracket
Ceiling Canopy
Canopy Bottom
Cover

5
Installing Fan to
the Electrical Box
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR OTHER PERSONAL INJURY.
MOUNT FAN ONLY TO AN OUTLET BOX OR
SUPPORTING SYSTEM MARKED ACCEPTABLE
FOR FAN SUPPORT AND USE THE MOUNTING
SCREWS PROVIDED WITH THE OUTLET BOX.
Figure 6
ETL Listed Outlet Box
Ceiling Mounting
Bracket
120V
Wires
Mounting
Screws (Supplied
with Electrical Box)
Figure 7A
Safety Cable
Ceiling
Mounting
Bracket
Pass the 120-volt supply wires through the
center hole in the ceiling mounting bracket as
shown in Figure 6.
Install the ceiling mounting bracket on the
outlet box with the screws and washers
provided with your outlet box. (Figure 6)
Security tighten the two mounting screws.
Hanging the assembled fan onto the mounting
bracket, place the downrod ball into the
mounting bracket. (Figure 7)
Secure the safety cable to the building structure
as shown in Figure 7A.
1.
2.
3.
4.
5.
WARNING
THE TAB IN THE RING MUST REST IN THE
GROOVE OF THE HANGER BALL AS FIGURE 7.
FAILURE TO PROPERLY SEAT THE TAB IN THE
GROOVE COULD CAUSE DAMAGE TO WIRING.
Figure 7

Making the Electrical Connections
WARNING
TO AVOID POSSIBLE ELECTRICAL SHOCK, BE SURE ELECTRICITY IS TURNED OFF AT THE
MAIN FUSE BOX BEFORE WIRING.
NOTE
INSTALLATION OF THIS FAN REQUIRES THAT A THREE-CONDUCTOR CABLE WITH
GROUND WIRE BE RUN BETWEEN CEILING AND WALL OUTLET BOX, OR THE OSCILLAT-
ING FEATURE WILL NOT WORK.
Disconnect the power and remove the existing wall plate and switch from the wall outlet box (Figure 8).
Set knob on the wall control in 0 position.
Make wire connections as follows, using the wire nuts supplied:
a. Speed/oscillation control wire connection (see figure 9)
CONNECT
(From speed/oscillation switch)
Blue wire (FOR OSCILLATION)….........…………
Black wire (TO MOTOR L)………………………..
Black/white wire (AC IN L)………………………..
Yellow/green ground wire……........……………….
• If your wall outlet box has a ground wire (green or bare copper), connect the Speed/oscillation control's yellow/green ground wire to it; otherwise
connect the Speed/oscillation control's yellow/green ground wire directly to one of the screws from the wall outlet box.
b. Fan wire connection (see figure 10)
CONNECT
(From fan)
Blue fan wire …………….............
Black fan wire …………….............
White wire……………....…............
Green wire………………................
1.
2.
3.
If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed
by a licensed electrician.
Figure 8
Switch
Wall Outlet Box Wall Plate
Screws
Screws
6
Figure 9
BLUE
BLACK
BLACK
WHITE
BLACKW/
WHITE
BLUE (or RED)
TO
(From wall outlet box)
Blue or red wire
White wire
Black wire from A/C supply source
Outlet box green wire
TO
(Conductor cable between ceiling and wall outlet box)
Blue or red wire
White wire
White wire from A/C supply source
Ground conductor of 120V supply, it may be a bare wire or a wire with green colored insulation.
YELLOW/GREEN
GROUND

7
Figure 10
SUPPLY CIRCUIT
BLUE (or RED)
BLUE
BLACK BLUE
BLACK
Ground
Conductor
Ceiling Outlet Box
Green Ground
Lead
YELLOW/GREEN
GROUND
Ground to
Downrod
GREEN
WHITE WHITE
Wall Outlet Box
BLACK
BLACK
BLACKW/WHITE
BLACK
WHITE
WHITE
Speed/oscillation Switch
BLUE(or RED)
• Dash lines are 3-conductor cable between ceiling and wall outlet box.