Hantek DSO8072E User manual

（V1.0.1）
DSO8000E SERIES
HANDHELD OSCILLOSCOPE
8072E/8102E/8152E/8202E
USER’S MANUAL

Contents
DSO8000E Series HandHeld Oscilloscope User Manual i
Contents
Contents........................................................................................................................................... i
Copyright Declaration................................................................................................................... iv
Chapter 1 Safety Tips................................................................................................................. 1
General Safety Summary .................................................................................................. 11.1
Safety Terms and Symbols................................................................................................ 11.2
Terms on Product............................................................................................................... 21.3
Symbols on Product........................................................................................................... 21.4
Product Scrapping ............................................................................................................. 21.5
Chapter 2 Overview.................................................................................................................... 3
Brief Introduction to DSO8000E Series............................................................................. 32.1
Help System....................................................................................................................... 32.2
Ports and Extentions.......................................................................................................... 42.3
Chapter 3 Getting Started Guide .............................................................................................. 5
Installation.......................................................................................................................... 53.1
Functional Check............................................................................................................... 53.2
3.2.1 Power on the oscilloscope.......................................................................................... 5
3.2.2 Connect the oscilloscope ........................................................................................... 5
3.2.3 Observe the waveform ............................................................................................... 6
Probe Examination............................................................................................................. 63.3
3.3.1 Safety.......................................................................................................................... 6
3.3.2 Use of Probe Check Wizard....................................................................................... 7
Manual Probe Compensation............................................................................................ 73.4
ProbeAttenuation Setting.................................................................................................. 83.5
Self Calibration................................................................................................................... 83.6
Communication with PC .................................................................................................... 93.7
3.7.1 Install software............................................................................................................ 9
3.7.2 Install driver .............................................................................................................. 12
Chapter 4 Main Feature Description ...................................................................................... 16
Oscilloscope Setup.......................................................................................................... 164.1
Trigger.............................................................................................................................. 164.2
Data Acquisition............................................................................................................... 174.3
Waveform Scaling and Positioning.................................................................................. 18
4.4
Waveform Measurement.................................................................................................. 194.5
Chapter 5 Basic Operation...................................................................................................... 20
DisplayArea...................................................................................................................... 215.1
5.1.1 XY Format................................................................................................................. 23
Horizontal Controls .......................................................................................................... 245.2
5.2.1 Scan Mode Display (Roll Mode)............................................................................... 26

Contents
DSO8000E Series HandHeld Oscilloscope User Manual ii
Vertical Controls............................................................................................................... 265.3
5.3.1 Math FFT.................................................................................................................. 28
Trigger Controls............................................................................................................... 335.4
Menu and Option Buttons................................................................................................ 395.5
5.5.1 SAVE/RECALL ......................................................................................................... 39
5.5.2 MEASURE................................................................................................................ 40
5.5.3 UTILITY .................................................................................................................... 42
5.5.4 DISPLAY................................................................................................................... 43
5.5.5 ACQUIRE ................................................................................................................. 44
5.5.6 CURSOR.................................................................................................................. 46
Fast Action Buttons.......................................................................................................... 475.6
5.6.1 AUTOSET................................................................................................................. 47
Signal Connectors............................................................................................................ 485.7
Chapter 6 Application Examples............................................................................................ 50
Example 1: Taking Simple Measurements ...................................................................... 506.1
Example 2: Taking Cursor Measurements....................................................................... 526.2
Example 3:Analyzing Input Signals to Eliminate Random Noise................................... 556.3
Example 4: Capturing Single-shot Signal........................................................................ 566.4
Example 5: Using X-Y Mode............................................................................................ 576.5
Example 6: Triggering on Pulse Width............................................................................ 586.6
Example 7: Triggering on Video Signal........................................................................... 596.7
Example 8: Using Slope Trigger to Capture Particular Slope Signal.............................. 616.8
Example 9: Using Overtime Trigger to Measure Long Pulse Signal............................... 626.9
Example 10: Using Math Functions toAnalyze Waveforms............................................ 636.10
Example 11: Measuring Data Propagation Delay............................................................ 64
6.11
6.12 Example 12: Back light control ........................................................................................ 65
6.13 Example 13:Auto shut down........................................................................................... 66
Chapter 7 Multimeter................................................................................................................ 67
Chapter 8 Recorder.................................................................................................................. 76
Multimeter Trend.............................................................................................................. 778.1
Oscilloscope Trend.......................................................................................................... 798.2
Waveform Recorder......................................................................................................... 808.3
Chapter 9 Waveform Generator.............................................................................................. 83
Waveform Generator ....................................................................................................... 839.1
Generate Arbitrary waveform........................................................................................... 86
9.2
9.2.1 EditArb waveform by DDS_ARB ............................................................................. 86
9.2.2 EditArb waveform by slave computer...................................................................... 89
Chapter 10 Troubleshooting.................................................................................................. 92
Problem Settlement......................................................................................................... 9210.1
Chapter 11 Specifications...................................................................................................... 93

Contents
DSO8000E Series HandHeld Oscilloscope User Manual iii
Technical Specifications................................................................................................... 9311.1
11.2 Accessories...................................................................................................................... 99
Open Source Information............................................................................................... 10011.3
License: GPLV2 See Appendix B....................................................................................... 100
Chapter 12 General Care and Cleaning.............................................................................. 101
General Care ................................................................................................................. 10112.1
Cleaning......................................................................................................................... 10112.2
Battery Replacement..................................................................................................... 10112.3
Chapter 13 Services and Support....................................................................................... 102
Appendix A Harmful and Poisonous Substances or Elements.......................................... 103
Appendix B.................................................................................................................................. 104
GNU GENERAL PUBLIC LICENSE............................................................................................ 104
Version 2, June 1991.................................................................................................................. 104

Copyright Declaration
DSO8000E Series HandHeld Oscilloscope User Manual iv
Copyright Declaration
All rights reserved; no part of this document may be reproduced or transmitted in any form or by
any means, electronic or mechanical, without prior written permission from Qingdao Hantek
Electronic Co., Ltd (hereinafter referred to as ‘Hantek’).
Hantek reserves all rights to modify this document without prior notice. Please contact Hantek for
the latest version of this document before placing an order.
Hantek has made every effort to ensure the accuracy of this document but does not guarantee the
absence of errors. Moreover, Hantek assumes no responsibility in obtaining permission and
authorization of any third party patent, copyright or product involved in relation to the use of this
document.

Safety Tips
DSO8000E Series HandHeld Oscilloscope User Manual 1
Chapter 1Safety Tips
General Safety Summary1.1
Read the following safety precautions to avoid injury and prevent damage to this product or any
products connected to it. To evade potential hazards, use this product only as specified.
Only qualified personnel should perform maintenance.
Avoid fire or personal injury.
Connect and disconnect properly. Connect a probe with the oscilloscope before it is connected
to measured circuits; disconnect the probe from the oscilloscope after it is disconnected from
measured circuits.
Connect the probe in a right way. The probe ground lead is at ground potential. Do not connect
the ground lead to an elevated voltage.
Check all terminal ratings. To avoid fire or shock hazard, check all ratings and markings on the
product. Refer to the product manual for detailed information about ratings before making
connections to the product.
Do not operate without covers. Do not operate this product with covers or panels removed.
Avoid exposed circuitry. Do not touch exposed connections and components when power is
present.
Do not operate with suspected failures. If you suspect there is damage to this product, have it
inspected by qualified service personnel.
Assure good ventilation.
Do not operate in wet/damp environments.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Safety Terms and Symbols1.2
The following terms may appear in this manual:
WARNING. Warning statements point out conditions or practices that could result in injury
or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in damage
to this product or other property.

Safety Tips
DSO8000E Series HandHeld Oscilloscope User Manual 2
Terms on Product
1.3
The following terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the marking.
WARNING indicates an injury hazard not immediately accessible as you read the marking.
CAUTION indicates a possible hazard to this product or other property.
Symbols on Product1.4
The following symbols may appear on the product:
Product Scrapping1.5
Device Recycling
We need extract and utilize natural resources to produce this device. If you do not reclaim the
device in a proper way, some substances it contains may become harmful or poisonous to
environments or human bodies. To avoid them being released outside and to minimize the waste
of natural resources, we suggest you reasonably call back this device to ensure proper recovery
and recycling of most materials within it.
Protective
Ground
(Earth)
Terminal
Measurement
Ground
Terminal
CAUTION
Refer to Manual
Measurement
Input Terminal
Mains
Disconnected
OFF (Power)
Mains
Connected
ON (Power)
High Voltage

Overview
DSO8000E Series HandHeld Oscilloscope User Manual 3
Chapter 2 Overview
Brief Introduction to DSO8000E Series2.1
Model
Channel
Bandwidth
Sample Rate
LCD
DSO8072E
2
70MHz
1GS/s
5.6 TFT
DSO8102E
2
100MHz
1GS/s
5.6 TFT
DSO8152E
2
150MHz
1GS/s
5.6 TFT
DSO8202E
2
200MHz
1GS/s
5.6 TFT
Table 2-1 Model List of DSO8000E Series
DSO8000E Series oscilloscopes cover the bandwidths from 70MHz to 200MHz, and provide
the real-time and equivalent sample rates respectively up to 1GSa/s and 25GSa/s. In addition,
they have maximum 2M memory depth for better observation of the waveform details, and 5.6 inch
color TFT LCD as well as WINDOWS-style interfaces and menus for easy operation.
What’s more, the plenty menu information and the easy-to-operate buttons allow you to gain
information as much as possible in measurement; the multifunctional and powerful shortcut keys
help you save a lot of time in operation; the Autoset function lets you detect sine and square
waves automatically; the Probe Check Wizard guides you to adjust the probe compensation and
set the Probe option attenuation factor. By using these the methods the oscilloscope provides
(context-sensitive, hyperlinks, and an index), you may master all operations on the device in quite
a short time so as to greatly improve your efficiency in production and development.
Help System2.2
This oscilloscope has a Help system with topics covering all of its features. You can use the Help
system to display several kinds of information:
General information about understanding and using the oscilloscope, such as Using the Menu
System.
Information about specific menus and controls, such as the Vertical Position Control.
Advice to problems you may come across while using an oscilloscope, such as Reducing
Noise.
Keep pressing a Function Menu button(including “SAVE/RECALL”, “MEAS”, “UTILITY”,
“CURSOR”, “CH1”, “CH2”, “MATH”, “HORI”and “TRIG”) for 3s to turn on the help file for the
function.

Overview
DSO8000E Series HandHeld Oscilloscope User Manual 4
Ports and Extentions
2.3
On the right side of the unit,
On the left side of the unit,
Attention: SD card memory should be less than or equal to 4GB.
Power Input DC 12V, 3000mA
Probe calibration signal output 1 KHz, 2Vpp
Type USB-A port for USB flash disk
LAN/Wifi connection port (optional)
Mini USB OTG port
Headphone, not available for this product.
Socket for Micro SD card (optional).

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 5
Chapter 3 Getting Started Guide
Installation3.1
To keep proper ventilation of the oscilloscope in operation, leave a space of more than 5cm away
from the top and the two sides of the product.
Functional Check3.2
Follow the steps below to perform a quick functional check to your oscilloscope.
3.2.1 Power on the oscilloscope
Press the ON/OFF button. The default Probe option attenuation setting is 10X.
The default probe parameter
Note 1: Between pressing the power key and the first screen appears on the screen, there is a
1~2 seconds delay without any screen.
Note 2: Right after power on, there are beep sounds at regular interval in the first few minutes. It
indicates that the multimeter is initializing and has no influence on use.
3.2.2 Connect the oscilloscope
Set the switch on the probe to 1X and connect the probe to Channel 1 on the oscilloscope. First,
align the slot in the probe connector with the protuberance on the CH1 BNC and push to connect;
then, turn to right to lock the probe in place; after that, connect the probe tip and reference lead to
the PROBE COMP connectors. The Probe COMP: ~2V@1KHz.
CH1
CH2

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 6
3.2.3 Observe the waveform
Press the AUTO button and you should see within a few seconds a square wave of about 2V
peak-to-peak at 1KHz in the display. Press the CH1 MENU button and remove Channel 1. Push
the CH2 MENU button and repeat Step 2 and Step 3 to observe Channel 2.
Probe Examination3.3
3.3.1 Safety
When using the probe, keep your fingers behind the guard on the probe body to avoid electric
shock. Do not touch metallic portions of the probe head while it is connected to a voltage source.
Connect the probe to the oscilloscope and connect the ground terminal to ground before you start
any measurements.
PROBE COMP

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 7
3.3.2 Use of Probe Check Wizard
Every time you connect a probe to an input channel, you should use the probe check wizard to
verify that this probe is operating correctly. There are two ways to do this:
1）Use the vertical menu (for example, push the CH1 MENU button) to set the Probe option
attenuation factor.
2）Press UTILITY key and turn to 3/5 page and then press the Probe CK key to use the Probe
Check Wizard and configure the probe option attenuation factor properly following menu
prompts.
Manual Probe Compensation3.4
Upon the first connection of a probe and an input channel, you should manually perform this
adjustment to match the probe to the input channel. Uncompensated or miscompensated probes
may lead to errors or faults in measurement. To adjust the probe compensation, follow the steps
below.
1. Set the Probe option attenuation in the channel menu to 10X. Set the switch on the probe to
10X and connect the probe to Channel 1 on the oscilloscope. If you use the probe hook-tip,
ensure it is firmly inserted onto the probe. Attach the probe tip to the PROBE COMP
~2V@1KHz connector and the reference lead to the PROBE COMP Ground connector.
Display the channel and then press the AUTO button.
2. Check the shape of the displayed waveform.
3. If necessary, use a nonmetallic screwdriver to adjust the variable capacity of your probe until
the shape of the waveform turns to be the same as the above figure. Repeat this step as
Compensated correctly
Overcompensated
Undercompensated

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 8
necessary. See the figure below for the way of adjustment.
Probe Attenuation Setting3.5
Probes are of various attenuation factors which affect the vertical scale of the signal. The Probe
Check function is used to verify if the Probe attenuation option matches the attenuation of the
probe.
As an alternative method to Probe Check, you can push a vertical menu button (such as the CH 1
MENU button) and select the Probe option that matches the attenuation factor of your probe.
Make sure that the Attenuation switch on the probe matches the Probe option in the oscilloscope.
Switch settings are 1X and 10X.
When the Attenuation switch is set to 1X, the probe limits the bandwidth of the oscilloscope to
6MHz. To use the full bandwidth of the oscilloscope, be sure to set the switch to 10X.
Self Calibration3.6
The self calibration routine helps optimize the oscilloscope signal path for maximum measurement
accuracy. You can run the routine at any time but should always run it if the ambient temperature
changes by 5℃or more. For a more accurate calibration, please power on the oscilloscope and
wait for 20 minutes until it has adequately warmed up.
To compensate the signal path, disconnect any probes or cables from the front-panel input
connectors. Then, push the UTILITY button, select the Self Cal option and follow the directions on
the screen.

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 9
Communication with PC
3.7
3.7.1 Install software
Caution: You must install the software before using the oscilloscope with Windows PC.
1. While in Windows, insert the installation CD into the CD-ROM drive.
2. The installation should start up automatically. Otherwise in Windows Explorer, switch to the
CD-ROM driver and run Setup.exe.
3. The software Installation is started. Click 'Next' to continue.

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 10
4. Choose a destination directory. Click ‘Next’ to continue.
5. Check the setup information. Click Next to start copying of files.
6. This Status dialog is displayed during copying of files.

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 11
7. Updating your system configuration.
8. The installation is complete.

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 12
3.7.2 Install driver
Caution: You must install the driver before connect the device with Windows PC via USB cable.
1. Connect the A-Type Plug of USB cable to your PC’s USB port.
2. Connect the B-Type Plug of USB cable to DSO’s USB port.
3. New hardware is found.
4. New hardware search wizard starts.

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 13
5. New hardware search wizard starts to search the drive.
6. New hardware wizard installs software

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 14
7. Finish new hardware search wizard.
12. Your new hardware is installed and ready to use.

Getting Started Guide
DSO8000E Series HandHeld Oscilloscope User Manual 15
13. Now you can open the software to use.