Hantek 6000EU User manual

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 1
USER’S MANUAL
Hantek 6000EU
V1.0.1
http://www.Hantek.com

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 2
Content
General Safety Summary ..............................................................................4
Chapter 1 Getting Start..................................................................................5
1.1 System Requirement...........................................................................................................6
1.2 Install Software And Driver .................................................................................................7
1.3 General Features ...............................................................................................................10
1.4 General Check ...................................................................................................................11
1.5 Function Check..................................................................................................................13
1.6 Self Calibration ..................................................................................................................14
1.7 Accessories ........................................................................................................................15
Chapter 2 Operating Basics........................................................................16
2.1 The User’s Interface...........................................................................................................17
2.2 The Menu System..............................................................................................................19
2.3 The Vertical System ...........................................................................................................21
2.4 The Horizontal System.......................................................................................................22
2.5 The Trigger System ............................................................................................................23
2.6 Input Connector ................................................................................................................24
Chapter 3 Oscilloscope Functions.............................................................26
3.1 Setup the Oscilloscope ......................................................................................................27
3.2 Set Vertical System ............................................................................................................28
3.3 Setup Horizontal System ...................................................................................................34
3.4 Set Trigger System .............................................................................................................35
3.5 Save/Load..........................................................................................................................40
3.6 Recorder............................................................................................................................40
3.7 Utility Function..................................................................................................................41
3.7.1 Pass/Fail.................................................................................................................42
3.7.2 F/C .........................................................................................................................44
3.7.3 Factory Setup.........................................................................................................45
3.7.4 Language ...............................................................................................................45
3.8 Measure Signal ..................................................................................................................46
3.7.1 Cursor Menu...........................................................................................................46
3.7.2 Measure Menu.......................................................................................................49
3.8 The Display System............................................................................................................52
3.8.1 Display Type............................................................................................................52
3.8.2 Display Grid ............................................................................................................53
3.8.3 Intensity..................................................................................................................54
3.8.4 Grid Background Color ...........................................................................................55
3.8.5 Color Mode.............................................................................................................56
3.8.6 Persis. Time ............................................................................................................58
3.8.7 Channel Delay........................................................................................................59
3.9 Zoom In/Out and Drag Waveforms ...................................................................................60
3.10 Interpolation ...................................................................................................................61
3.11 Acquisition Modes...........................................................................................................63
3.12 Acquisition Option...........................................................................................................63
3.13 Print And Print Preview ...................................................................................................66
Chapter 4 Application Example ..................................................................68

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 3
4.1 Simple Measurement ........................................................................................................69
4.2 Capturing a Single-Shot Signal...........................................................................................70
4.3 The Application of the X-Y Operation................................................................................70
4.4 Taking Cursor Measurements............................................................................................72
Chapter 5 Appendix.....................................................................................75
Appendix A: Specifications......................................................................................................76
Appendix B: Accessories..........................................................................................................78
Appendix C: General Maintenance .........................................................................................78

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 4
General Safety Summary
Review the following safety precautions carefully before operate the device to avoid any
personal injuries or damages to the device and any products connected to it.
To avoid potential hazards use the device as specified by this user’s guide only.
■To Avoid Fire or Personal Injury
■Use Proper Power Cord. Use only the power cord specified for this product and certified
for the country of use.
■Connect and Disconnect Properly. Do not connect or disconnect probes or test leads
while they are connected to a voltage source.
■Connect and Disconnect Properly. Connect the probe output to the measurement
device before connecting the probe to the circuit under test. Disconnect the probe input
and the probe reference lead from the circuit under test before disconnecting the probe
from the measurement device.
■Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings and
markings on the product. Consult the product manual for further ratings information before
making connections to the product.
■Use Proper Probe. To avoid shock hazard, use a properly rated probe for your
measurement.
■Avoid Circuit or Wire Exposure. Do not touch exposed connections and components
when power is on.
■Do Not Operate With Suspected Failures. If suspected damage occurs with the device,
have it inspected by qualified service personnel before further operations.
■Provide Proper Ventilation. Refer to the installation instructions for proper ventilation of
the device.
■Do not operate in Wet/Damp Conditions.
■Do not operate in an Explosive Atmosphere.
■Keep Product Surfaces Clean and Dry.

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 5
Chapter 1 Getting Start
The oscilloscope is small, lightweight, 12V external power required, portable oscilloscopes!
The oscilloscopes is ideal for production test, research and design and all of the
applications involving analog circuits test and troubleshooting, as well as education and
training.
In addition to thelist of general features on the next page, this chapter describes how to do
the following tasks:
System Requirements
Install Software
General Features
General Check
Function Check
Self Calibration
Accessories

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 6
1.1 System Requirement
To run the oscilloscope software, the needs of computer configuration are as follows:
Minimum System Requirements
Operating System
Window Vista/Win7/Win8/Win10
Processor
Upwards of 1.00G processor
Memory
2G byte
Disk Space
500M disk free space
Screen resolution
1280 x 800 resolution
Recommended Configuration
Operating System
Windows Vista/Win7/Win8/Win10
Processor
2.4G Processor
Memory
4G Byte Memory
Disk Space
80G Disk Space
Screen resolution
1920 x 1080 resolution
DPI Setting
Normal Size (96DPI)

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 7
1.2 Install Software And Driver
Caution: You must install the software before using the oscilloscope.
1. While in Windows, insert the installation CD into the CD-ROM drive.
2. The installation should start up automatically. Otherwise in Windows Explorer, switch
to the CD-ROM drive and run Setup.exe.
3. The software Installation is started. Click 'Next' to continue.
4. Choose a destination directory. Click 'Next' to continue.
5. Check the setup information. Click Next to start copying of files.

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 8
6. This Status dialog is displayed during copying of files.
7. The installation is complete.

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 9
8. After software Installation it can be start the Device Driver Installation.Click Next to
start the Device Driver Installation.
9. Complete the Device Driver Installation.

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 10
1.3 General Features
Product Features:
■Four Channels, Max Bandwidth:
250MHz/200MHz/100MHz/70MHz
■Maximum real-time sample rate:
1GSa/s
■Memory depth:
128M /CH
■Automatic setup for ease of use (AUTOSET);
■Built-in Fast Fourier Transform function(FFT);
■20 Automatic measurements;
■Automatic cursor tracking measurements;
■Waveform storage, record and replay dynamic waveforms;
■User selectable fast offset calibration;

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 11
■Add, Subtract and Multiply Mathematic Functions;
■Selectable 20 MHz bandwidth limit;
■Waveform average;
■Adjustable waveform intensity, more effective waveform view;
■User interface in several user-selectable languages;
■Waveform capture rate to 60,000 wfm/s,400,000wfm/s(FastAcq mode)
■Intensity graded color display
■SATA Interface communication
1.4 General Check
Please check the instrument as following steps after receiving an oscilloscope:
Check the shipping container for damage:
Keep the damaged shipping container or cushioning material until the contents of the
shipment have been checked for completeness and the instrument has been checked
mechanically and electrically.
Check the accessories:
Accessories supplied with the instrument are listed in "Accessories" in this guide. If the
contents are incomplete or damaged, please notify the franchiser.
Check the instrument:
In case there is any mechanical damage or defect, or the instrument does not operate
properly or fails performance tests, please notify the franchiser.
Probe Compensation
Perform this function to match the characteristics of the probe and the channel input.
This should be performed whenever attaching a probe to any input channel at the first
time.

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 12
■From the “Probe” menu, select attenuation to 1:10. Set the switch to “X10” on the probe
and connect it to CH1 of the oscilloscope. When using the probe hook-tip, insert the tip
onto the probe firmly to ensure a proper connection.
■Attach the probe tip to the Probe Compensator and the reference lead to the ground
connector, select CH1, and then press the “AUTOSET“ button into the menu or the
toolbar.
■Check the shape of the displayed waveform.
Correctly Compensated
Over Compensated
Under Compensated
1. If necessary, use a non-metallic tool to adjust the trimmer capacitor of the probe for the
fattest square wave being displayed on the oscilloscope.
2. Repeat if necessary.
WARNNING: To avoid electric shock while using the probe, be sure the perfection of the
insulated cable, and do not touch the metallic portions of the probe head while it is
connected with a voltage source.

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 13
1.5 Function Check
Perform this functional check to verify that your oscilloscope is operating correctly.
■Connect the oscilloscope
You should connect the A-Type Plug ofUSB cable to your PC USB portand connect the
other A-Type Plug of USB cable to oscilloscope USB port.
■Input a signal to a channel of the oscilloscope
The oscilloscope is equipped with two channels plus external trigger.
Please input signal in the following steps:
1. Set the attenuation switch on the probe as 10X and connect the probe on the
oscilloscope with CH1. Aim the slot in the probe connector at the faucet on BNC of CH1
and insert, then, turn right to lock the probe. Finally, attach the tip of probe and ground nip
to the Connector of Probe compensator.
2. Set the CH1 probe attenuation of the oscilloscope to X10. (The default is X1).

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 14
3. Attach the tip of probe and ground nip to the Connector of Probe compensator. Click the
button. A square wave will be displayed within a several seconds. (Approximately 1
kHz, 2V, peak- to- peak).
4. Inspect CH2 with the same method. Repeat steps 2 and 3.
1.6 Self Calibration
The self calibration routine lets you optimize the oscilloscope signal path for maximum
measurement accuracy. You can run the routine at any time but you should always run
the routine if the ambient temperature changes by 5℃or more. For accurate calibration,
power on the oscilloscope and wait twenty minutes to ensure it is warmed up. To
compensate the signal path, disconnect any probes or cables from the input connectors.
Then, access the “Utility -> Calibration” option and follow the directions on the screen.
The self calibration routine takes about several minutes.

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 15
1.7 Accessories
All the accessories listed below are standard accessories for the oscilloscope:
Hantek 6000EU:
Probe x 2 (1.5m), 1:1(10:1), Passive Probes
A USB cable
Alligator clip wire x 2
QuickGuide
A software installation CD

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 16
Chapter 2 Operating Basics
The User’s Interface
The Menu System
The Vertical System
The Horizontal System
The Trigger System
Input Connectors

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 17
2.1 The User’s Interface
Click the software icon on the desk after you finished the software setting and equipment
connecting. Then a user interface will be showed as follows:
In addition to displaying waveforms, the display area is filled with many details about the
waveform and the oscilloscope control settings.
1. The Main Menu: All settings can be found in the main menu.
2. The Toolbar
3. Displays the trigger information: Displays the edge trigger slope, source and level.
4. The Connect Panel
5. The Horizontal Panel: The user can change Time/Div, format in the panel.
6. The Vertical Panel: The user can turn on/off the CH1/CH2/CH3/CH4. Also the user
can change the CH1/ CH2/CH3/CH4 volt/div, coupling and probe attenuation.
7. The Trigger Panel: In this panel, the user can change the trigger mode, sweep, source
and slope.
8. Marker shows Edge trigger level

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 18
9. Move Wareform
10. Displays the system time.
11. Sample rate
12. The markers show the CH1/CH2/CH3/CH4 reference points of the displayed
waveforms. If there is no marker,the channel is not displayed.
13. Connect
14. Displays the CH1/CH2/CH3/CH4 information:
Readouts show the coupling of the channels.
Readouts show the vertical scale factors of the channels.
A “B” icon indicates that the channel is bandwidth limited
15. Marker shows horizontal trigger position.
16. Trigger status indicates the following:
AUTO: The oscilloscope is in auto mode and is acquiring waveforms in the absence of
triggers.
Trig’D: The oscilloscope has seen a trigger and is acquiring the post trigger data.
STOP: The oscilloscope has stopped acquiring waveform data.
RUN: The oscilloscope is running.

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 19
2.2 The Menu System
The Main Menu:
1.File: Load or Save data, setup
2.View: Change the user interface
3.Setup:Setup setting
4.Display:Change wave display type

Hantek 6000EU Digital Oscilloscope
USER’S MANUAL 20
5.Cursor: Set Cursor measure type
6. Measure: Set measurement parameters
7.Acquire: Run ,Stop or other operation setting
8. Utility: Utility setting
9. Window: Window setting