Harbor Breeze QUONTA CFH52BNK5L User manual

QUONTA LED CEILING FAN
MODEL #CFH52BNK5L
CFH52MBK5L
CFH52WW5L
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-527-1292, 8:30 a.m. - 5 p.m., CST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Purchase Date
1
Español. 17
ITEM #2599766
2807160
2807161
4007498

TABLE OF CONTENTS
Modifications not approved by the party responsible for compliance could void the user's authority to
operate the equipment.
*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Distributed by: Litex Industries Inc., P.O. Box 535639, Grand Prairie, TX, 75053; 1-800-527-1292
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: Dimmable to 10% with select dimmers.
SAFETY INFORMATION
Safety Information ................................................................................................................................2
Package Contents ................................................................................................................................5
Hardware Contents ..............................................................................................................................6
Preparation ..........................................................................................................................................6
Initial Installation ..................................................................................................................................6
Wiring ...................................................................................................................................................8
Final Installation .................................................................................................................................10
Operating Instructions ......................................................................................................................13
Care and Maintenance .......................................................................................................................14
Troubleshooting..................................................................................................................................15
Limited Lifetime Warranty ..................................................................................................................16
Replacement Parts List ......................................................................................................................16
2

READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, install or operate the
product.
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage that
might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to
the floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan including the light kit is: 15.87 lbs.
SAFETY INFORMATION
To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for the
support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box; do NOT use a
plastic outlet box. Secure the outlet box directly to the building structure. The outlet box and its
support must be able to support the moving weight of the fan (at least 35 lbs.).
To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp
edges.
To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan
are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
WARNING
DANGER
When using an existing outlet box, make sure the outlet box is securely attached to the building
structure and can support the full weight of the fan. Failure to do this can result in serious injury or
death. The stability of the outlet box is essential in minimizing wobble and noise in the fan after
installation is complete.
To reduce the risk of serious bodily injury, DO NOT use power tools to assemble any part of the fan,
including the blades.
3

4
SAFETY INFORMATION
CAUTION
Read all instructions and safety information before installing your new fan. Review the
accompanying assembly diagrams.
Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.
Once installation is complete, carefully check all screws, bolts and nuts on fan motor assembly
to ensure that they are secured.
Do NOT tamper with or attempt to repair LED component. The light source is designed for this
specific application and should not be serviced by untrained personnel. If any servicing is
required, call our customer service department.
WARNING
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not bend the blades when
installing or balancing them or cleaning the fan. Do not insert objects between the rotating fan
blades.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
WARNING

H Fitter Plate Screw 3
(preassembled to Fitter
plate (C))
I Mounting Plate Screw 4
(preassembled to Mounting
Plate (A))
PACKAGE CONTENTS
5
DESCRIPTIONPART QUANTITY DESCRIPTIONPART QUANTITY
IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
F
B
G
A
A Mounting Plate 1
B Motor Housing 1
C Fitter Plate 1
D LED Light Kit 1
E Shade 1
F Blade 5
G Motor Plate Screw 3
(preassembled to Motor
Housing (B))
C
D
E
I
H

6
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble
the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and Wire
Cutters
HARDWARE CONTENTS (shown actual size)
PREPARATION
DD
Pull Chain
Extension
Qty. 2
CC
Blade
Screw
Qty. 15
+ 1 extra
Wire
Connector
Qty. 4
BB
AA
Fiber Blade
Washer
Qty. 15
+ 1 extra
Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
INITIAL INSTALLATION
ON
OFF
ON
OFF
1

This fan can be mounted as a flushmount on a
regular (no-slope) ceiling only.
Check to make sure blades (F) will be at least
30 in. from any obstruction and at least 7 ft. above
the floor.
7
2.
Locate preassembled mounting plate screw (I) on
outer edge of mounting plate (A) closest to the
J-hook (located on underside of mounting plate
(A)) and remove that mounting plate screw (I).
Then, remove mounting plate screw (I) on outer
edge of mounting plate (A) directly opposite the
mounting plate screw (I) that was just removed.
Partially loosen the other two remaining mounting
plate screws (I).
3.
INITIAL INSTALLATION
3
I
I
A
2
7 ft.
min.
30 in.
min.
F
Secure mounting plate (A) to outlet box using
screws, spring washers and flat washers provided
with the outlet box.
*NOTE: It is very important you use the proper
hardware when installing the mounting plate (A)
as this will support the fan.
4. 4
A
J-hook

5. Lift motor housing (B) to mounting plate (A) and
then hang motor housing (B) on J-hook on
underside of mounting plate (A). (Use one of the
non-slotted holes on the rim of the motor housing
(B) to do so.) This will allow motor housing (B) to
hang out of the way while wiring.
INITIAL INSTALLATION
5
8
WIRING
WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided
with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If
your house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
CAUTION: Be sure outlet box is properly grounded and that a ground (green or bare) wire is
present.
WARNING: If house wires are different colors than referred to in the following steps, stop
immediately. A professional electrician is recommended to determine wiring.
WARNING: Using a full range dimmer switch (not included) to control fan speed will cause a loud
humming noise from fan. To reduce the risk of fire or electrical shock, do NOT use a full range dimmer
switch to control fan speed.
NOTE: This fan is remote control adaptable (remote control not included). Please refer to instructions
provided with the remote control before proceeding with these wiring instructions.
Choose wiring diagram (Fig. 1a, Fig. 1b or Fig. 1c)
that fits your situation and make appropriate wiring
connections as follows: [IMPORTANT: Use one of
the wire connectors (CC) provided to make each wire
connection, making sure to screw wire connector
(CC) on in a clockwise direction.]
1a. FAN AND LIGHT CONTROLLED BY PULL
CHAINS: Connect BLACK and BLUE wire from fan
to BLACK wire from ceiling. Connect WHITE wire
from fan to WHITE wire from ceiling. Connect
GROUND (GREEN) mounting plate (A) and motor
housing to BARE/GREEN wire from ceiling.
1.
1a
FAN AND LIGHT CONTROLLED BY PULL CHAINS
120V POWER
FROM CEILING
BLACK (POWER)
WHITE (NEUTRAL)
GROUND/GREEN (BARE)
Non-slotted
Hole
J-Hook
B
GREEN
WHITE BLACK
BLUE
CC
CC
CC
L
o

9
Wrap electrical tape (not included) around each
individual wire connector (CC) down to the wire.
WARNING: Make sure no bare wire or wire
strands are visible after making connections. Place
BARE/GREEN and WHITE connections on
opposite side of box from the BLACK and BLUE (if
applicable) connections.
2.
2.
CC
2
CC
CC
Hardware Used
Wire Connector x 4
CC
WIRING
1b. FAN CONTROLLED BY PULL CHAIN, LIGHT
BY WALL SWITCH: Connect BLACK wire from fan
to BLACK wire from ceiling. Connect BLUE wire
from fan to the BLACK wire from the independent
wall switch for the light. Connect WHITE wire from
fan to WHITE wire from ceiling. Connect GROUND
(GREEN) wires from motor housing (B), if
applicable, and mounting plate (A) to
BARE/GREEN wire from ceiling.
FAN CONTROLLED BY PULL CHAIN, LIGHT BY WALL SWITCH
1b
BLACK
BLUE
120V POWER
FROM CEILING
BLACK (POWER)
BLACK (WALL SWITCH)
WHITE (NEUTRAL)
GROUND/GREEN (BARE)
GREEN
CC
CC CC
CC
1c. FAN AND LIGHT CONTROLLED BY TWO
WALL SWITCHES: Connect BLACK wire from fan
to BLACK (or RED) wire from the independent
wall switch for the fan. Connect BLUE wire from
fan to the BLACK (or RED) wire from the other
independent wall switch for the light. Connect
WHITE wire from fan to WHITE wire from ceiling.
Connect GROUND (GREEN) wires from motor
housing (B) and mounting plate (A) to
BARE/GREEN wire from ceiling.
NOTE: BLACK wire is hot power for fan. BLUE wire
is hot power for light kit. WHITE wire is common for
fan and light kit. GREEN or BARE wire is ground.
BLACK (WALL SWITCH)
BLACK (WALL SWITCH FOR LIGHT)
FAN AND LIGHT CONTROLLED BY TWO WALL SWITCHES
FAN AND LIGHT CONTROLLED BY TWO WALL SWITCHES
1c
WHITE
BLACK
BLUE
120V POWER
FROM CEILING
WHITE (NEUTRAL)
GROUND/GREEN (BARE)
GREEN
CC
CC CC
CC
WHITE

Motor
Plate
Male
Plug
I
G
I
G
10
FINAL INSTALLATION
1. Remove motor housing (B) from J-hook. Lift
motor housing (B) to mounting plate (A). Align
slotted holes on top rim of motor housing (B) with
loosened mounting plate screws (I) in mounting
plate (A). Twist motor housing (B) to lock.
Re-insert the two mounting plate screws (I)
previously removed (step 3, page 7) and then
tighten all four mounting plate screws (I) to
secure motor housing (B).
1
I
I
B
J-hook
Slotted
Hole
Remove one preassembled motor plate screw
(G) from motor plate (on underside of motor)
and partially loosen the other two motor plate
screws (G). Align slotted holes in fitter plate (C)
with loosened motor plate screws (G), allowing
female plug from motor housing (B) to come
through hole in middle of fitter plate (C). Twist
fitter plate (C) to lock. Re-insert motor plate
screw (G) that was removed and tighten all
three motor plate screws (G) securely.
3. 3
2.
Hardware Used
Insert a blade (F) through one of the slots on the
band on the motor housing (B). Align holes and
attach the blade (F) to the motor with blade
screws (AA) and fiber blade washers (BB).
Then, tighten each blade screw (AA), starting
with the one in the middle. Repeat for remaining
blades (F).
AA Blade Screw x 15
Fiber Blade Washer x 15
BB
B
F
B
2
(View from Underside)
A
GC
AA
BB

11
FINAL INSTALLATION
Remove one preassembled fitter plate screw
(H) from underside of fitter plate (C) and
partially loosen the other two fitter plate
screws (H).
4. 4
D
molex
connections
5
Connect WHITE molex wire from LED light kit
(D) to WHITE molex wire from fitter plate (C).
Connect BLUE molex wire from LED light kit (D)
to BLACK (or BLUE) molex wire from fitter plate
(C). Make sure molex wire connections snap
together securely.
5.
C
6. Connect male plug from motor housing (B) to
female plug from fitter plate (C), matching up
the colors on the male plug with the colors on
the female plug for correct fit. Make sure plugs
are connected completely.
6B
Male Plug Female Plug
H
H
C
C

12
FINAL INSTALLATION
Align grooves on shade (E) with nodules on
inside of fitter plate (C) and push up gently on
shade (E). Turn shade (E) clockwise until it no
longer turns.
NOTE: Pull down gently on the shade (E) to
make sure that it is secured completely.
8. 8
E
C
D
C
Carefully arrange wires in center of fitter plate
(C). Align slotted holes in edge of LED light kit
(D) with loosened fitter plate screws (H) on fitter
plate (C). Re-insert the other fitter plate screw
(H) previously removed. Tighten all three fitter
plate screws (H) securely.
7. 3
7
H
HH
B
Attach pull chain extensions (DD) or custom pull
chain extensions (not included) to fan and light
pull chains.
Assembly is now complete.
9. 9
DD DD
Pull Chain Extension x 2
Hardware Used
DD

13
OPERATING INSTRUCTIONS
The light pull chain, located to the left of the reverse
switch, is used to turn the light ON or OFF.
The fan pull chain, located to the right of the
reverse switch, has four positions to control fan
speed. One pull is HIGH, two is MEDIUM, three
is LOW and four turns the fan OFF.
1.
2. 2
1
Reverse
Switch
Use the fan reverse switch on the fitter plate (C) to
optimize your fan for seasonal performance. A
ceiling fan will allow you to raise your thermostat
setting in summer and lower your thermostat
setting in winter without feeling a difference in your
comfort.
NOTE: Wait for fan to stop before moving the
reverse switch.
3.
C
3
Reverse
Switch
Reverse
Switch

14
At least twice each year, lower motor housing (B) to check mounting plate (A) assembly, and then
tighten all screws. Clean motor housing (B) with only a soft brush or lint-free cloth to avoid scratching
the finish. Clean blades (F) with a lint-free cloth. You may occasionally apply a light coat of furniture
polish to wood blades for added protection.
IMPORTANT: Shut off main power supply before beginning any maintenance. Do not use water or a
damp cloth to clean the ceiling fan.
• Total wattage for this fixture is 18 watts; do not attempt to replace the LEDs.
CARE AND MAINTENANCE
OPERATING INSTRUCTIONS
3a 3b
3c
3c. IMPORTANT: Reverse switch must be set
either completely LEFT or completely RIGHT for
fan to function. If the reverse switch is set in the
middle position, fan will not operate.
3a. In warmer weather, setting the reverse switch
in the LEFT position will result in downward airflow
creating a wind chill effect.
3b. In cooler weather, setting the reverse switch
in the RIGHT position will result in upward airflow
that can help move stagnant, hot air off the ceiling
area.

15
WARNING: Before beginning work, shut off the power supply to avoid electrical shock.
NOTE: A small amount of "wobble" is normal and should not be considered a defect.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Fan does not move. 1. Reverse switch not engaged.
2. Power is off or fuse is blown.
3. Faulty wire connection.
4. Plugs in fitter plate not connected
properly.
1. Push switch firmly either left or
right.
2. Turn power on or check fuse.
3. Turn power off. Loosen canopy
and check all connections.
4. Check that male and female plugs
in fitter plate are connected
properly according to instructions
on page 11.
Noisy operation. 1. Blades are loose.
2. Cracked blade.
3. Full range dimmer switch.
4. Fan is new.
1. Tighten all blade screws.
2. Replace blade.
3. Replace with an approved speed
control device.
4. Allow fan a “break in” period of
a few days, especially when
running the fan at Medium and
High speeds.
Excessive wobbling. 1. Blades are loose.
2. Unbalanced blades.
3. Fan not securely mounted.
1. Tighten all blade screws.
2. Switch one blade with a blade
from the opposite side.
3. Turn power off. Carefully loosen
motor housing and verify that
mounting plate is secure.
Fan operates but
light fails.
1. Wires in motor housing not wired
properly.
2. Wall switch to fan is off.
3. Wires in LED light kit not wired
correctly.
1. Check wires in motor housing
and, if necessary, re-wire
according to instructions on
pages 8 and 9.
2. Make sure that wall switch to fan
is on.
3. Check that molex connections in
LED light kit are connected
properly according to instructions
on page 11.

16 Printed in China
GGLI2008
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-800-527-1292, 8:30 a.m. - 5 p.m., CST,
Monday - Friday.
A
A Mounting Plate
F Blade
02807161-A
02807161-F
02807160-A
02807160-F
02599766-A
02599766-F
The distributor warrants this fan to be free from defects in workmanship and materials present at time
of shipment from the factory for Lifetime limited from the date of purchase. This warranty applies only
to the original purchaser. The distributor agrees to correct any defect at no charge or, at our option,
replace the ceiling fan with a comparable or superior model.
To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of
removal and reinstallation are the express responsibility of the purchaser. Any damage to the ceiling
fan by accident, misuse or improper installation, or by using parts not produced by the manufacturer
of this fan or affixing accessories not produced by the manufacturer of this fan, are the purchaser's
own responsibility. The distributor assumes no responsibility whatsoever for fan installation during
the limited lifetime warranty. Any service performed by an unauthorized person will render the
warranty invalid.
Due to varying climatic conditions, this warranty does not cover changes in brass finish, rusting,
pitting, tarnishing, corroding or peeling. Brass finish fans maintain their beauty when protected from
varying weather conditions. Any glass provided with this fan is not covered by the warranty.
Any replacement of defective parts for the ceiling fan must be reported within the first year from the
date of purchase. For the balance of the warranty, call our customer service department (at
1-800-527-1292)for return authorization and shipping instructions so that we may repair or replace
the ceiling fan. Any fan or parts returned improperly packaged is/are the sole responsibility of the
purchaser. There is no further express warranty. The distributor disclaims any and all implied
warranties. The duration of any implied warranty which cannot be disclaimed is limited to the limited
lifetime period as specified in our warranty. The distributor shall not be liable for incidental,
consequential or special damages arising at or in connection with product use or performance except
as may otherwise be accorded by law. This warranty gives you specific legal rights and you may also
have other rights which vary from state to state. This warranty supersedes all prior warranties.
LIMITED LIFETIME WARRANTY
F
#2807161
PART #
#2807160
PART #
#2599766
PART #
PART DESCRIPTION

VENTILADOR DE
TECHO QUONTA
17
ADJUNTE SU RECIBO AQUÍ
Fecha de compra
¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro
Departamento de Servicio al Cliente al 1-800-527-1292, de lunes a viernes de 8:30 a.m. a
5 p.m.
ARTÍCULO #2599766
2807160
2807161
MODELO #CFH52BNK5L
CFH52MBK5L
CFH52WW5L
4007498

18
Información de seguridad ....................................................................................................................18
Contenido del paquete ........................................................................................................................21
Lista de aditamentos ...........................................................................................................................22
Preparación .........................................................................................................................................22
Instalación inicial .................................................................................................................................22
Cableado .............................................................................................................................................24
Instalación final.....................................................................................................................................26
Instrucciones de funcionamiento ........................................................................................................29
Cuidado y mantenimiento ....................................................................................................................30
Solución de problemas ........................................................................................................................31
Garantía limitada de por vida ..............................................................................................................32
Lista de piezas de repuesto .................................................................................................................32
ÍNDICE
Las modificaciones que no estén aprobadas por la parte responsable del cumplimiento podrían
anular la autorización del usuario para utilizar el equipo.
*NOTA: este equipo ha sido probado y se ha verificado que cumple con los límites para un
dispositivo digital clase B, conforme a la sección 15 de las reglas de la FCC. Estos límites se han
diseñado para proporcionar una protección razonable contra la interferencia perjudicial en una
instalación residencial. Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, si
no se instala y se usa de acuerdo con las instrucciones, puede causar interferencia perjudicial a las
comunicaciones de radio. Sin embargo, no se garantiza que no se producirán interferencias en una
instalación en especial. Si este equipo genera una interferencia perjudicial para la recepción de
radio o televisión, que se puede determinar apagando y encendiendo el equipo, se recomienda al
usuario que intente corregir la interferencia con una o más de las siguientes medidas:
* Reoriente o reubique la antena de recepción.
* Aumente la separación entre el equipo y el receptor.
* Conecte el equipo a un tomacorriente de un circuito distinto al que usa el receptor.
Solicite ayuda al distribuidor o a un técnico con experiencia en radio/TV.
Distribuido por: Litex Industries Inc., P.O. Box 535639, Grand Prairie, TX, 75053; 1-800-527-1292
Este dispositivo cumple con la Parte 15 de las Reglas de la FCC. La operación está sujeta a las dos
siguientes condiciones: (1) Este dispositivo no provoca ninguna interferencia perjudicial; (2) Este
dispositivo aceptará cualquier interferencia que reciba, incluyendo aquellas que provoquen una
operación no deseada.
NOTA: se puede regular al 10 % con reguladores seleccionados.
INFORMACIÓN DE SEGURIDAD

19
INFORMACIÓN DE SEGURIDAD
Para reducir el riesgo de incendio, descargas eléctricas o lesiones personales, monte
el ventilador en una caja de salida marcada como "ACCEPTABLE FOR FAN
SUPPORT OF 35 LBS. OR LESS" (“APTA PARA SOSTENER VENTILADORES DE
15,87 KG O MENOS”) y utilice los tornillos de montaje que se proporcionan con la caja de salida.
La mayoría de las cajas de salida que se usan comúnmente para sostener lámparas no son aptas
para sostener un ventilador y puede ser necesario reemplazarlas. Si tiene dudas, consulte a un
electricista calificado.
Cuando monte el ventilador en una caja de salida del techo, use una caja de salida octogonal de
METAL; NO use una caja de salida de plástico. Asegure la caja de salida directamente a la
estructura del edificio. La caja de salida y el soporte deben ser capaces de sostener el peso del
ventilador en movimiento (al menos 15,87 kg).
Para reducir el riesgo de incendios, descargas eléctricas o lesiones personales, los conectores de
cables incluidos con este ventilador están diseñados para soportar solo un cable de la casa de
calibre 12 y dos cables conductores desde el ventilador. Si el cable de la casa es de un calibre
superior a 12 o hay más de un cable de la casa para conectar a los cables conductores del
ventilador correspondientes, consulte a un electricista cuál es el tamaño adecuado de los
conectores de cables que debe utilizar.
ADVERTENCIA
PELIGRO
Si utiliza una caja de salida existente, asegúrese de que esté bien sujeta a la estructura del edificio
y que pueda sostener el peso del ventilador. El incumplimiento de dicho paso podría provocar
lesiones graves o la muerte. La estabilidad de la caja de salida es fundamental para minimizar el
balanceo y el ruido en el ventilador una vez que la instalación esté completa.
Para reducir el riesgo de lesiones corporales graves, NO utilice herramientas eléctricas para
ensamblar las piezas del ventilador, incluidas las aspas.
LEA Y GUARDE ESTAS INSTRUCCIONES
Lea y comprenda completamente este manual antes de intentar ensamblar, instalar o usar el
producto.
• No deseche la caja del ventilador ni los accesorios de espuma. En caso de que deba devolver este
ventilador a la fábrica para realizarle reparaciones, se debe enviar en su embalaje original para
asegurar una protección adecuada contra daños que puedan aumentar la causa inicial de la
devolución.
• Asegúrese de que todas las conexiones eléctricas cumplan con los códigos y ordenanzas locales,
el Código Eléctrico Nacional y la norma ANSI/NFPA 70-1999. Si no está familiarizado con la
instalación del cableado eléctrico, contrate a un electricista calificado o consulte un manual de
cableado para hacerlo usted mismo.
• Asegúrese de que en el lugar de instalación que elija se pueda establecer una distancia mínima
de 2,13 m desde las aspas hasta el piso y al menos 76,2 cm desde los extremos de las aspas hasta
cualquier obstáculo.
• Una vez que el ventilador esté instalado, asegúrese de que todas las conexiones sean seguras
a fin de evitar que se caiga.
• El peso neto de este ventilador, junto con el kit de iluminación, es de: 7,2 kg.

20
INFORMACIÓN DE SEGURIDAD
Para evitar lesiones personales, puede ser necesario usar guantes al manipular las piezas del
ventilador con bordes filosos.
Para reducir el riesgo de incendios o descargas eléctricas, no use el ventilador con dispositivos de
control de velocidad para ventiladores de estado sólido ni controle la velocidad del ventilador con
un regulador de intensidad de rango completo.
Para reducir el riesgo de incendio, descargas eléctricas o lesiones personales, no doble las
aspas al instalarlas, equilibrarlas o al limpiar el ventilador. No coloque objetos entre las aspas
en movimiento.
Para reducir el riesgo de lesiones personales, use SOLO las piezas que se proporcionan con este
ventilador. El uso de piezas DISTINTAS a aquellas que se proporcionan con este ventilador anulará la
garantía.
Antes de proceder, asegúrese de cortar la alimentación eléctrica del interruptor principal o
interruptor de circuito a fin de evitar descargas eléctricas.
ADVERTENCIA
Asegúrese de que la caja de salida tenga la puesta a tierra correcta y de que haya un conductor
(verde o desnudo) de puesta a tierra.
Una vez que termine la instalación, revise cuidadosamente todos los tornillos, pernos y tuercas
del ensamble del motor del ventilador para comprobar que estén asegurados.
Lea todas las instrucciones y la información de seguridad antes de instalar el ventilador nuevo.
Revise los diagramas de ensamble adjuntos.
NO manipule ni intente reparar el componente LED. La fuente de luz está diseñada para esta
aplicación específica y el mantenimiento no debe estar a cargo de personal sin capacitación.
Si necesita algún tipo de mantenimiento, llame a nuestro Departamento de Servicio al Cliente.
PRECAUCIÓN