Harbor Breeze 41107 User manual

Harbor Breeze® is a registered trademark
of LF, LLC. All Rights Reserved.
1
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday,
8 a.m. - 5 p.m., EST, Friday.
ATTACH YOUR RECEIPT HERE
Purchase Date _________________________
BM18022
ITEM #0176493, 0179178, 0922357, 0922356
LANSING CEILING FAN
MODEL #40948, 40949, 41108, 41107
Español p. 21

2
TABLE OF CONTENTS
Package Contents .................................................................3
Hardware Contents ................................................................4
Safety Information .................................................................5
Preparation ......................................................................6
Initial Installation ..................................................................7
Standard or Angled Mounting Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Closemount Instructions ...........................................................11
Wiring .........................................................................12
Final Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operating Instructions .............................................................17
Care and Maintenance ............................................................18
Troubleshooting..................................................................18
Limited Lifetime Warranty ..........................................................19
Replacement Parts List ............................................................20

3
PACKAGE CONTENTS
I
F
E
KMN
PART DESCRIPTION QUANTITY
A Downrod 1
B Downrod Pin (preassembled to Downrod [A]) 1
C Downrod Clip (preassembled to Downrod [A]) 1
D Mounting Bracket (preassembled to Canopy [E]) 1
E Canopy 1
F Canopy Cover (preassembled to Canopy [E]) 1
G Light Kit 1
H Glass Shade 3
IMotor Assembly 1
J Fitter Plate (preassembled to Motor Assembly [I]) 1
K Yoke Cover 1
L Blade Arm 5
M Blade 5
N Bulb 3
O Motor Screw (preassembled to Motor Assembly [I]) 10
P Set Screw (preassembled to Motor Assembly [I]) 2
Q Phillips-head Closemount Screw (preassembled to Motor Assembly [I]) 3
R Mounting Bracket Screw (preassembled to Mounting Bracket [D]) 4
S Fitter Plate Screw (preassembled to Fitter Plate [J]) 3
A
CB
D
E
F
G
H
I
J
K L M N
O
P
Q
R
S

4
HARDWARE CONTENTS
Wire
Connector
Qty. 3
+ 1 extra
Blade Screw
Qty. 15
+ 1 extra
Blade Washer
Qty. 15
+ 1 extra
Pull Chain Extension
Qty. 2
Motor Screw
1 extra
H
a
r
b
o
r
B
r
e
e
z
e
H
a
r
b
o
r
B
r
e
e
z
e
AA BB CC DD
XX

5
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
• Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit
breakers.
• Make sure that all electrical connections comply with local codes, ordinances, the National
Electrical Code, and ANSI/NFPA 70-199. Hire a qualied electrician or consult a do-it-yourself
wiring handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to
the oor and at least 30 in. from the end of the blades to any obstruction.
• The net weight of this fan is: 14.01 lbs.
DANGER: When using an existing outlet box, make sure the outlet box is securely attached to
the building structure and can support the full weight of the fan. Failure to do this can result in serious
injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan
after installation is complete.
WARNING: To avoid personal injury, the use of gloves may be necessary while handling fan
parts with sharp edges.
WARNING: Using a full-range dimmer switch to control fan speed will cause a loud humming
noise from the fan. To reduce the risk of re or electric shock, do NOT use a full-range dimmer switch
to control the fan speed.
WARNING: To reduce the risk of re or electric shock, do NOT use this fan with any solid-state
speed control device.
WARNING: To reduce the risk of re, electric shock, or personal injury, mount the fan to an
outlet box marked “ACCEPTABLE FOR FAN SUPPORT” and use the mounting screws provided with
the outlet box. Most outlet boxes commonly used for the support of lighting xtures are not acceptable
for fan support and may need to be replaced. Consult a qualied electrician if in doubt. Secure the
outlet box directly to the building structure. The outlet box and its support must be able to support the
moving weight of the fan (at least 35 lbs.).
WARNING: To reduce the risk of re, electrical shock, or personal injury, wire connectors
provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from
the fan. If your house wire is larger than 12-gauge or there is more than one house wire to connect to
the two fan lead wires, consult an electrician for the proper size wire connectors to use.
WARNING: To reduce the risk of re, electric shock, or personal injury, do not bend the blade
arms when installing them, balancing the blades, or cleaning the fan. Do not insert objects between
the rotating fan blades.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use
of parts OTHER than those provided with this fan will void the warranty.

6
SAFETY INFORMATION
CAUTION: Read all instructions and safety information before installing your new fan. Review the
accompanying assembly diagrams.
CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present.
CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are
secured.
PREPARATION
Before beginning the assembly of this product, ensure that all parts are present. Compare all parts
with the package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 90 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Step Ladder and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Wiring Handbook and Wire Cutters

7
INITIAL INSTALLATION
1. Turn off the circuit breakers and the wall switch to the
fan supply line leads.
DANGER: Failure to disconnect the power
supply prior to installation may result in serious injury
or death.
2. Determine the mounting method to use.
Standard Mounting is best suited for ceilings 8 ft.
or higher. For taller ceilings you may want to use a
longer downrod (sold separately).
Angle mounting is best suited for angled or vaulted
ceilings. A longer downrod is sometimes necessary
to ensure proper blade clearance. Important: If using
the angle mount, check to ensure the ceiling angle is
not steeper than 16°.
Flushmount installation is not available for this item.
Closemount installation is more suitable for
ceilingslower than 8 ft. high.
2
Standard Mounting
Flushmount Closemount
Angle Mounting
3. Ensure that the blades (M) will be at least 30 in. from
any obstructions. Also check the downrod (A) length
to ensure the blades (M) will be at least 7 ft. above
the oor.
7 ft. min.
30 in. min.
A
1
3
A
M

8
INITIAL INSTALLATION
4. Loosen all four mounting bracket screws (R), then
completely remove the two mounting bracket screws
(R) from the round holes of canopy (E). Set aside for
later use.
Detach mounting bracket (D) from canopy (E).
E
D
R
5. Attach mounting bracket (D) to outlet box (not
included) using screws and washers provided with the
outlet box.
CAUTION: It is very important you use the proper
hardware when installing the mounting bracket (D) as
it will support the fan.
6. Remove the 10 preassembled motor screws (O) and
ve preassembled motor blocks from the underside of
the motor assembly (I). Discard the motor blocks but
save the motor screws (O) for later.
For Standard or Angle Mounting Instructions,
continue to page 9. For Closemount Instructions,
proceed to page 11.
4
5
6
Motor
Block
Standard and
Closemount
Mounting
Angle
Mounting
D
D
R
E
D
D
O
I

9
STANDARD OR ANGLED MOUNTING INSTRUCTIONS
1. Remove the downrod clip (C) and downrod pin (B) from
the downrod (A). Then partially loosen the set screws
(P) in the yoke at the top of the motor assembly (I).
2. Insert the downrod (A) through the canopy (E)
and yoke cover (K). Feed the wires from the motor
assembly (I) through the downrod (A).
3. Slide the downrod (A) into the yoke of the motor
assembly (I), align the holes, then re-install the
downrod pin (B) and downrod clip (C). Secure with set
screws (P) and slide the yoke cover (K) down until it
rests on top of the motor assembly (I).
1
I
Yoke
A
BC
P
I
E
K
I
A
K
C
BI
2
3
P
A
P

10
STANDARD OR ANGLED MOUNTING INSTRUCTIONS
4. Depending on the length of downrod you use, you may
need to cut the lead wires back to simplify the wiring. If
you decide to cut back the lead wires, it is suggested
that you do so in the following manner: Take the lead
wires and make sure that you have pulled them all the
way through the top of the downrod and measure 8 in.
of lead wire, and then cut the excess wire off with wire
cutters (not included).
5. If you decided to cut back the lead wire in Step 4, strip
1/2 in. of insulation from the end of the white wire. Twist
the stripped ends of each strand of wire within the
insulation with pliers (not included). Repeat this step for
black and blue wires.
Important: If you did not cut back the lead wires in
Step 4, Step 5 is not necessary and you may proceed
to Step 6.
6. Install the ball end of the downrod (A) into the opening
of mounting bracket (D). Align one of the four slots in
the downrod with the tab in the mounting bracket (D).
Note: The downrod (A) should not rotate if installed
correctly.
DANGER: Failure to align the slot in the downrod
(A) with the tab of the mounting bracket (D) could
cause the fan to fall, resulting in serious injury or death.
Proceed to the Wiring on page 12.
4
6
Tab
Slot
5
8 in.
D
A

11
CLOSEMOUNT INSTRUCTIONS
Helpful Hint: The downrod (A), canopy cover (F) and
yoke cover (K) are not used in this type of installation.
1. Remove the canopy cover (F) from the bottom of the
canopy (E).
2. Remove three Phillips-head closemount screws (Q)
from the top of the motor assembly (I). Align the canopy
(E) with the holes in the top of the motor assembly (I),
then re-install the Phillips-head closemount screws
(Q) to secure the canopy (E) to the top of the motor
assembly (I).
3. Raise the fan and place the canopy (E) on the hook on
the mounting bracket (D), temporarily leaving hands free
for the wiring process.
1
2
3
Hook
E
F
Q
E
I
E
D

12
WIRING
WARNING: To reduce the risk of re, electrical shock or personal injury, wire connectors provided
with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If
your house wire is larger than 12-gauge and there is more than one house wire to connect to the two
fan lead wires, consult an electrician for the proper size wire connectors to use.
CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is
present.
1. Connect supply and fan wires according to the diagram
and these steps:
• Connect the Green wires from the downrod (A)
and the mounting bracket (D) to the Bare/Green
(ground) supply wire. Note: Closemount installation
does not use downrod (A), so there will only be two
Green wires to connect.
• Connect the White wire from the fan to the White
(neutral) supply wire.
• Connect the Black and Blue wires from the fan to the
Black (hot) supply wire.
Secure all wiring connections together with wire
connectors (AA).
Note: If a second hot power wire is available from outlet
box, connect it to the blue (light power) wire from the
fan for separate light and fan control.
Note: The Blue wire is power for light. The Black wire
is power for the fan. The White wire is neutral/common.
The Green wire is the ground wire. If household supply
wires are different colors than referred to above, it is
recommended a professional electrician determines the
proper wiring.
Hardware Used
AA Wire Connector x 3
2. Wrap electrical tape (not included) around each
individual wire connector (AA) down to the wire.
3. Turn the spliced/taped wires upward and gently push
the wires and wire connectors into the outlet box.
WARNING: Ensure no bare wire strands are visible
after making connections. Place Green and White wire
connections on opposite sides of outlet box from the
Black and Blue wire connections.
1D
AA
AA
3
2
Black (Hot)
White (Neutral)
Bare/Green (Ground)
Black Blue White Green

13
FINAL INSTALLATION
1. Align the canopy (E) over the loosened mounting
bracket screws (R) preassembled on mounting
bracket (D). Place the keyholes of the canopy (E)
onto the mounting bracket screws (R) and rotate the
canopy (E) clockwise.
2. Secure the canopy (E) with the mounting bracket screws
(R) previously removed (Step 4, page 8). Tighten all
mounting bracket screws (R) securely.
1
2
E
2
R
R
E
D
E
Note:Closemount installation will not have the downrod (A), yoke cover (K) or canopy cover (F).

14
FINAL INSTALLATION
3. Partially insert three blade screws (BB) along with three
blade washers (CC) through one blade (M) and into one
blade arm (L). Tighten each blade screw (BB) with a
Phillips screwdriver (not included), starting with the one
in the middle. Repeat this step for the remaining blades
(M) and blade arms (L).
Hardware Used
BB Blade Screw x 15
CC Blade Washer x 15
4. Install the blade arm (L) to the underside of the motor
assembly (I) with motor screws (O) previously removed
(Step 6, page 8). Tighten with Phillips screwdriver (not
included).
Repeat for each blade arm (L).
5. Remove the tter plate screws (S) preassembled to the
tter plate (J). Then, connect the 9-pin connectors from
the tter plate (J) and the light kit (G).
3
4
5
14
9-pin Connector
BB
CC
M
L
I
O
L
G
JS

15
FINAL INSTALLATION
6. Assemble the light kit (G) to the tter plate (J) using
the previously removed tter plate screws (S).
7. Screw the twist-on glass shades (H) onto the sockets
of the light kit (G).
8. Install bulbs (N) into the sockets of the light kit (G).
Important: Make sure to allow the bulbs (N) and light
kit (G) to cool before you replace the bulbs.
6
7
8
S
G
G
H
G
N

16
FINAL INSTALLATION
9. Attach the pull chain extensions (DD) or custom pull
chain extensions (not included) to the fan and light pull
chains.
Hardware Used
DD Pull Chain
Extensions x 2
DD
H
a
r
b
o
r
B
r
e
e
z
e
H
a
r
b
o
r
B
r
e
e
z
e
Fan Pull
Chain
Light Pull
Chain
10. Turn on power supply to the fan.
Assembly is complete.
10
9
DD
H
a
r
b
o
r
B
r
e
e
z
e
H
a
r
b
o
r
B
r
e
e
z
e

17
OPERATING INSTRUCTIONS
1. The fan pull chain has four positions to control the fan
speed. One pull is HIGH, two is MEDIUM, three is LOW,
and four turns the fan OFF. The pull chain in the center
of the light kit (G) turns the lights ON and OFF.
2. Using a ceiling fan will allow you to raise your
thermostat setting in summer and lower your
thermostat setting in winter without feeling a
difference in your comfort. Note: Wait for the fan to
stop before moving the reverse switch located on the
light kit (G).
In warmer weather, push the reverse switch left
to display a sun icon, which will result in downward
airow creating a wind chill effect (Fig. 2a).
In cooler weather, push the reverse switch right to
display a snowake icon, which will result in upward
airow that can help move hot air off the ceiling area
(Fig. 2b).
Important: The reverse switch must be set either
completely left or right in order for the fan to function
correctly. If the reverse switch is set in the middle
position, the fan will not operate (Fig. 2c).
Fig. 2C
3
Fig. 2A Fig. 2B
1
16
Lowes.com/harborbreeze
H
a
r
b
o
r
B
r
e
e
z
e
H
a
r
b
o
r
B
r
e
e
z
e
Light Pull Chain Fan Pull Chain
2
G
G

18
CARE AND MAINTENANCE
At least twice each year, lower the canopy to check the downrod assembly, and then tighten all
screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching
the nish. Clean the blades with a lint-free cloth.
Bulb Replacement: Use 60-watt max. candelabra-base bulbs, LED or CFL equivalent.
Important: Shut off the main power supply before you begin any maintenance task. Do not use water
or a damp cloth to clean the fan.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The fan does not
move.
1. The reverse switch is not
engaged.
2. The wall switch is turned off.
3. The power is off or the fuse
(breaker) is blown.
4. There is a faulty wire
connection.
1. Firmly push the reverse switch to either the
left or right.
2. Make sure the wall switch is turned on.
3. Turn the power on or check the fuse
(breaker).
4. Turn the power off and check all
connections at the ceiling outlet box.
The fan is noisy.
1. The blades are loose.
2. There is a cracked blade.
3. The wall control is not
compatible with the fan.
4. The outlet box is not secure.
5. The mounting bracket is not
secure.
1. Check and tighten all screws that hold the
fan blades to the blade arms and the motor.
2. Replace the cracked blade.
3. Do not use a full range dimmer switch to
control the fan speed.
4. Ensure the outlet box is secured to the
building structure.
5. Ensure the mounting bracket is secured to
the outlet box and that the screws are tight.
There is
excessive
wobbling.
1. The blades and/or blade are
loose.
2. The blades are unbalanced.
3. The fan mounting is not
secure.
4. The fan is too close to the
vaulted ceiling.
5. The set screw on the motor
housing yoke is loose.
1. Check and tighten all screws that hold the
fan blades to the blade arms and the blade
arms to the motor.
2. Switch one blade with a blade from the
opposite side. Or balance the fan using a
blade balancing kit (sold separately).
3. Turn off the power. Loosen the canopy and
verify that the mounting bracket is secure to
the electrical outlet box. The bracket must
be ush without movement against the
outlet box.
4. Use a longer downrod or move the fan to
another location.
5. Lift up the yoke cover and tighten the set
screw to the yoke until secure.

19
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The fan operates
correctly, but
the lights are
not working (if
applicable).
1. The bulb(s) not installed
correctly.
2. The light kit wire plugs are not
connected properly.
3. There is a faulty wire
connection.
4. The total power of the light is
exceeding 190 W.
1. Re-install the bulb(s).
2. Ensure that the male and female
plugs in the light kit tter are
connected properly.
3. Turn the power off and check all
connections at the ceiling outlet box.
4. The fan comes with a 190 W limiter.
When the total watts of the lights is
over 190 W, the lights do not work.
Please replace the bulbs with lower-
wattage bulbs.
LIMITED LIFETIME WARRANTY
The manufacturer warrants this fan to be free from defects in workmanship and materials present at
time of shipment from the factory for a lifetime from the date of purchase by the original purchaser.
The retailer also warrants that all other fan parts, excluding any glass or plexiglass blades, to be free
from defects in workmanship and material at the time of shipment from the factory for a period of one
year after the date of purchase by the original purchaser. The manufacturer agrees to correct such
defects without charge or at its option replace the ceiling fan with a comparable or superior model.
To obtain warranty service, present a copy of the receipt as proof of purchase. All costs of removing
and reinstalling the product are your responsibility. Any damage to any part such as by accident or
misuse or improper installation or by afxing any accessories, is not covered by this warranty. The
manufacturer assumes no responsibility whatsoever for fan installation during the limited lifetime
warranty. Any service performed by an unauthorized person will render the warranty invalid.
Due to varying climate conditions, this warranty does not cover any changes in brass nish, including
rusting, pitting, corroding, tarnishing or peeling. Brass nishes of this type give their longest useful life
when protected from varying weather conditions. Any glass provided with this fan is not covered by
the warranty.
Any replacement of defective parts for the ceiling fan must be reported within the rst year from the
date of purchase. For the balance of the warranty, call our customer service department for return
authorization and shipping instructions so that we may repair or replace the ceiling fan. Any fan or
parts returned improperly is the sole responsibility of the purchaser. There is no other expressed
warranty. The manufacturer disclaims any and all warranties. The duration of any implied warranty
which cannot be disclaimed is limited to the time period as specied in the expressed warranty. The
manufacturer shall not be liable for incidental, consequential, or special damages arising out of or
in connection with product use or performance except as may otherwise be accorded by law. This
warranty gives specic legal rights, and you may also have other rights which vary from state to state.
This warranty supersedes all prior warranties.
Note:A small amount of “wobble” is normal and should not be considered a defect.

20 Printed in China
REPLACEMENT PARTS LIST
For replacement parts, call the customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST,
Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
PART DESCRIPTION 0179178 &
0922356
PART #
176493 &
0922357
PART #
A Downrod 4L000006400 4L000006340
D Mounting Bracket 4L000006410 4L000006350
E Canopy 4L000004350 4L000006360
F Canopy Cover 4L000002900 4L000006370
G Light Kit 4L000006820 4L000006810
H Glass Shade 4L000004760 4L000004090
K Yoke Cover 4L000000230 4L000000120
LBlade Arm 4L000003070 4L000000028
M Blade 4L084290001 4L084290002
HW Hardware Kit 4L000010890 4L000010900
K
8011-PB • 120418
A
H
D
K
E
L
F
M
G
HW