Harmar Mobility AL350 Operating instructions

Read and understand this manual thoroughly before
attempting to install or operate the lift. If you have any
questions, please contact your Authorized Harmar Dealer or
Harmar’s Technical Service Department.
P 800-833-0478 | F 866-234-5680 | [e-mail]
Dealer Name & Contact Information:
Serial # of Your Lift:
AL350
Installation & Owner’s Manual www.harmar.com | 800-833-0478
AL350 Hitch-Mounted
Scooter and Powerchair Lift
Capacity: 350 lbs
P/N: 610-00065 Rev A

2
Contents
NOTE: The following symbols indicate areas where you should take
special care to avoid danger to individuals or property.
Section 1: Owner
OPERATING YOUR LIFT
General Operation.................................3
Using a Swing-Away..............................6
Manual Override.................................... 8
9
SAFETY & MAINTENANCE
Section 2: Installer
PREPARATION
Tools Required............................................11
Unpacking theLift.....................................12
Installation Overview ...............................13
INSTALLATION
Wiring the Vehicle .....................................15
Vehicle Hitch................................................18
Hitch Adapters........................................... 19
Lift Installation
Hitch Post Mount ................................ 21
Swing-Away ................................................ 23
CHAIR PREPARATION 25
Anchor Plate ......................................... 25
U-Bolt Kit................................................ 26
27
30
TROUBLESHOOTING
WIRING DIAGRAM
EXPLODED VIEWS
WARRANTY 35
WARNING
Hazardous situation. If not avoided,
could result in serious injury to
installer or user.
CAUTION!
Hazardous situation. If not
avoided, could result in serious
damage to property.
| www.harmar.com | 800-833-0478
29

3
SECTION 1 : OWNER Operating Your Lift
GENERAL OPERATION
1. LOWERING THE LIFT
Insert key and switch to ‘ON’ position.Press
‘DOWN’ on toggle switch. The platform will
unfold. Continue to lower until platform reaches
the ground and becomes level. [Figure 3-1]
DO NOT over-lower to the point where the
vehicle begins to rise. This will damage the lift.
IMPORTANT
Positioning the chair properly on the platform is
critical to ensure it is properly locked onto the lift.
Always verify wheels are captured by cradles
or bars. Please consult your dealer on the specics
of your application.
Figure 3-1
Figure 3-2
2. DRIVE ONTO PLATFORM.
Drive slowly, stopping when the drive wheels fall
between the platform bars if applicable.[Figure
3-2]
AL350 Hitch-Mounted Scooter and Power Chair Lift P/N: 610-00065 Rev A

4
SECTION 1 : OWNER
Operating Your Lift
3. SECURING THE CHAIR
Ensure Chair or Scooter is Powered Off. You may wish to raise the platform halfway,
using the ‘UP’ toggle switch, in order to avoid having to bend over while you attach
straps.[Figure4-1]
x2
Figure 4-2
4. RAISING THE LIFT
When the chair is secure, use the ‘UP’ toggle
switch to continue raising the lift. Stop when
it reaches the top of travel when you hear the
clutch sound. Twist the key to remove.
[Figure 4-2]
Figure 4-1
| www.harmar.com | 800-833-0478

5
SECTION 1 : OWNER Operating Your Lift
CAUTION
These are general
instructions. Specics may
vary based on your chair
model and lift combination.
Please follow the specic
instruction suggested by
your dealer.
CAUTION
Always verify the chair or
scooter is held rmly in place
prior to transport.
•Always run the lift fully to the top
for transport. The lift will make a
ratcheting sound which indicates
that all mechanisms are locked and
prepared for travel.
•Never attempt to move the vehicle
without the lift being in the full up or
stowed position. This may damage the lift.
•Drive slowly over rough terrain such as
pot holes, unpaved roads, railroad tracks.
Excessive loads from rough driving will
damage your lift and is not covered by
the warranty.
•If you notice any damage, stop using
the lift immediately. Do not attempt
to transport a chair or scooter with a
compromised lift. Damage to your chair,
lift, vehicle may occur. Take the lift to
your nearest dealer and have it evaluated
prior to further use.
5. UNLOADING THE CHAIR
Insert the key and switch to ‘ON’ position.
Press ‘DOWN’ to lower the lift. Do NOT
continue travel to the point where the
vehicle rises; that will damage the lift.
[Figure 5-1]
Drive the chair o the platform carefully.
When the chair is unloaded, press ‘UP’ and
the platform will automatically fold.
Figure 5-1
AL350 Hitch-Mounted Scooter and Power Chair Lift P/N: 610-00065 Rev A

Remove
Safety
Pin
Pull
T-Handle
AL105 AL105L
Remove
Safety
Pin
Pull
T-Handle
AL105 AL105L
6
SECTION 1 : OWNER
Operating Your Lift
SWING-AWAY
The Swing-Away allows you to easily swing the
installed auto lift away from the back of the
vehicle for convenient access to the trunk or lift
gate. The Swing-Away option can be purchased
from an authorized dealer and added at any time.
NOTE: Two Swing-Away models areavailable,
a standard AL105and the lightweight
AL105L. They work basically the same way
but the parts differ slightly as noted in
[Figure 6-3].
Figure 6-2
WARNING
NEVER open the Swing-Away
with the chair on the lift.
You will damage the Swing-
Away and the lift. It will
potentially damage the vehicle
and the chair. Any of these
actions will VOID your warranty.
Figure 8-4
Remove
Safety
Pin
Pull
T-Handle
AL105 AL105L
Remove
Safety
Pin
Pull
T-Handle
AL105 AL105L
Figure 6-3
Figure 6-5
OPENING THE SWING-AWAY
1. Remove Safety Pin [Figure 6-3]
2. Pull T-Handle [Figure 6-4]
•Grasp the lift rmly and swing it out, away
from the vehicle. The Swing-Away can be
opened up to 180 degrees from the closed
position to allow full access to the
vehicle’s cargo area. [Figure 6-5]
WARNING
Figure 6-1
Open ONLYon Level Ground
Failure to open on level
ground may result in losing
control of the lift, resulting in
personal injury or damage to
property.
| www.harmar.com | 800-833-0478

7
SECTION 1 : OWNER Operating Your Lift
CLOSING THE SWING AWAY
Close the Swing-Away unit as you would a
car door.
WARNING
Stay clear of the latching
mechanism
Figure 7-1
SAFELY CLOSED WRONG
SAFELY CLOSED WRONG
Figure 7-2
Figure 7-3
WARNING
Always install the safety pin.
CAUTION
Verify that the T handle has
fully retracted.
AL350 Hitch-Mounted Scooter and Power Chair Lift
Figure 7-4
P/N: 610-00065 Rev A

VEHICLE HARNESS
LIFT HARNESS
VEHICLE HARNESS
LIFT HARNESS
REMOVE
3/8”
Turn COUNTER -
CLOCKWISE
to LOWER platform.
Turn CLOCKWISE
to RAISE platform.
8
SECTION 1 : OWNER
Operating Your Lift
Figure 8-1
Figure 10-2
Figure 8-2
MANUAL OVERRIDE
IMPORTANT!
You MUST unplug the two-connector plug BEFORE
any attempt to use the Manual Override. Failure to
do so result in serious injury.
WARNING
Disconnect power from lift
BEFORE attempting manual
override.
1. Unplug Power to the Lift. [Figure8-1]
2. Remove the cap on top of the motor.
[Figure 8-2]
3. Insert a 3/8” socket wrench into the
actuator and rotate the Hex Shaft. [Figure 8-3]
Figure 8-3
In the event of a power failure, for example
if your car battery dies, your lift can still
operate using the Manual Override system.
4. Turn COUNTER-CLOCKWISE to LOWER
the platform. [Figure 8-4]
5. Turn CLOCKWISE to RAISE the platform.
[Figure 8-4]
Figure 8-4
| www.harmar.com | 800-833-0478

CAUTION
!
CAUTION
!
9
SECTION 1 : OWNER Safety & Maintenance
SPECIAL CAUTIONS
• Beware of pinch points. These
are areas ofmechanical objects
with moving parts than can catch
extremities or clothing. Donotplace
fingers, extremities or allow clothing
near such points.
• Keep hands, feet and objects away
from Platform as it Lowers.
• Keep chair tires properly inated.
Improper inflation will change how the
chair fits and secures on the platform,
and changes the clamping pressure.
• Secure chair rmly before driving.
Double-check that is it secured
properly tothe platform before you
transport it.
•Inspect the lift condition often. If
ANY parts are worn or damaged, DO
NOT USE THE LIFT. Immediately contact
the dealer you purchased the lift from
for repairs.
•Do Not Enter Steep Driveways
Straight On. Enter and leave at an
angle to the street so that the lift does
not drag on the ground.
• Do Not Move the Vehicle with
Platform Down. If you move with the
platform in the down position, you will
damage the lift mechanism.
• Hand Wash or Use Touchless
Automatic Car Wash only. To
prevent lift damage do NOT use
automatic wash systems.
SAFETY & MAINTENANCE
WARNING!
This lift is NOT meant for human transport. The chair or
scooter MUST be unoccupied before operating the lift. Each
lift is designed to transport a specic chair only. DO NOT
attempt to move any mobility devices, objects, people, or
materials other than those for which the lift was designed.
CAUTION!
Drive with EXTREME CARE while transporting your chair or
scooter on the lift. DRIVE SLOWLY over rough terrain such as
pot holes, unpaved roads, railroad tracks. Excessive bumping
creates stress on the lift and vehicle and can badly damage
your lift, vehicle, and mobility device.
AL350 Hitch-Mounted Scooter and Power Chair Lift
Figure 9-1
P/N: 610-00065 Rev A

ESAERG ESAERG
ESAERG
10
SECTION 2 : INSTALLER
Safety & Maintenance
CAUTION!
Drive the scooter o
in REVERSE. When the
scooter is clear of the
platform, raise the
platform by pushing up
on the UP/DOWN switch.
MAINTENANCE
This Outside Lift is designed to be as trouble free as possible;
however, some basic maintenance will ensure that it continues
to oer reliable use for years to come.
Oil pivot points on all moving parts every 30 days.
Re-grease the inside vertical square tube every 30 days in
winter or in dirty or dusty conditions. Just lower the platform
to the ground and clean the tube with mineral spirits, WD-40,
or a good solvent. When clean, grease the square vertical tube
shaft with high grade water-resistant grease such as boat
trailer wheel bearing grease. [Figure 10-1]
Check for paint chips and touch up bare metal. Use a good
gloss black enamel or lacquer to inhibit rust. You may need to
do this more frequently if your lift is subject to salt air or road
salt in the winter.
Figure 10-1
| www.harmar.com | 800-833-0478

SOCKET SET
Specifically
WRENCH SET
Specifically
3/8”
7/16”
1/2"
9/16"
3/4"
7/16”
1/2"
9/16”
3/4"
ALLENWRENCH
Specifically
1/8”
3/16”
5/16”
#2 FLAT HEAD
SCREWDRIVER
#2 PHILLIPS HEAD
SCREWDRIVER
WIRE CUTTERS
NEEDLE NOSE
PLIERS
MARKING
IMPLEMENT TAPE MEASURE
11
SECTION 2 : INSTALLER Preparation
TOOLS REQUIRED
PROFESSIONAL INSTALLATION RECOMMENDED
Installations may vary to some degree, but below are the basic tools to have on hand for an
Outside Lift installation.
If you have any questions, concerns or comments, please contact our Technical Service
Department at 800-378-6648 or [e-mail]
If you do not understand any portion of installation or
operation, please consult our technical service department or
authorized mobility dealer. Do not attempt to install or use this
NOTE: The following section is designed for the professional
installer. We strongly recommend that a certied dealer
install the lift, congure the docking device, and instruct the
user on correct operation as well as establish a Safety and
Maintenance Schedule.
lift with any hesitation or question.
Serious injury or damage can result if
proper procedures are not followed.
Read & Understand this Manual
Prior to Installation or Operation.
Having an overall understanding
of the lift and proper installation
techniques will help you save time,
energy and avoid possible injury.
AL350 Hitch-Mounted Scooter and Power Chair Lift P/N: 610-00065 Rev A

12
SECTION 2 : INSTALLER
Preparation
UNPACKING THE LIFT
Check the box contents. Review each part against the packaging
checklist to ensure that all parts have been included.
If any parts are missing or damaged, immediately contact the dealer
who sold the lift. Do not attempt to install or use a lift that has missing
or damaged parts.
| www.harmar.com | 800-833-0478

X4
13
SECTION 2 : INSTALLER Preparation
INSTALLATION OVERVIEW
3. Determine / Install Hitch Height / Adapter.Measure the
hitch to ground distance so you can save time by selecting
components that fit between lift and vehicle so as to
maintain proper ground clearance. See pages 19-20. Install
Hitch Adapter that fits the application. Install Hitch Post
(shown) or swing-away. See pages 21-24.
Figure 13-1
Never attempt to pick up the lift from the box,
ground or on/off a vehicle alone.
If you follow the proper installation procedure, no
heavy lifting will be needed, and the lift practically
installs itself.
Read & understand this Manual prior
to installation or operation.
Knowing the lift’s adjustments and the tips on proper installation
techniques will save time, energy and avoid possible injury. If you
do notunderstand any portion ofinstallation or operation, please
consult ourtechnical service department or authorized mobility
dealer.
Quick Reference – Installation Procedure
1. Wire the Vehicle. See page 15.
Installing the wiring harness first will ensure you have power
to the lift during installation. This allows the motor to do the
lifting for you. (If you skip this step, use a shop battery.)
2 . Position th e
open box behin d
the vehicle. Sli ce
the corner seams.
[Figure13-1]
AL350 Hitch-Mounted Scooter and Power Chair Lift P/N: 610-00065 Rev A

Vehicle Harness
Lift Harness
Connect power
to the lift
Vehicle Harness
Lift Harness
Connect power
to the lift
3” or
more
PUSH
14
SECTION 2 : INSTALLER
Preparation
4. Connect power to the lift. [Figure14-1] Insert and turn key.
Press ‘DOWN’ to extend the lift. [Figure 14-2]
Figure 14-1
Figure 14-3
Figure 14-2
Figure 16-4
5. When extended 3” or more ip up to
vertical. [Figure 14-3]
6. Align the outer tube with hitch post
or swing-away (as shown) using the
power of the lift. The lift will slide on the
cardboard box. [Figure 14-4]
| www.harmar.com | 800-833-0478

TO BATTERY
TO LIFT
20 AMP SELF
RESETTING
CIRCUIT
BREAKER
TO BATTERY
TO LIFT
20 AMP SELF
RESETTING
CIRCUIT
BREAKER
YLNOERIWKCALB
SIDE MOUNT
BLACK WIRE
ONLY
OR
TOPMOUNT
YLNOERIWKCALB
SIDE MOUNT
BLACK WIRE
ONLY
OR
TOPMOUNT
15
SECTION 2 : INSTALLER Installation
WIRING THE VEHICLE
Improper wiring is the #1 cause of problems in the operation
of a vehicle lift. Follow the wiring instructions carefully
The vehicle wiring harness is located in the hardware pack.
The harness is manufactured to comply with SAE J1128
requirements. It is approximately 23 feet long and will
accommodate most vehicles.
1. Unwind the wiring harness and lay it at.
The harness end with the black connector is
the lift end. It goes to the trailer hitch area
where the lift will mount. [Figure15-1]
WARNING!
DO NOT connect
the red wire
until LAST.
2. Begin routing the wiring harness at the vehicle
battery. Attach the black wire to the negative terminal on
the battery. Do NOT attach the red wire until the very end
of installation. [Figure15-2]
CAUTION!
NEVER attempt to connect the harness to
a secondary power source. Always connect
both leads directly to the battery.
3. Run the vehicle harness under and, when possible,
through the vehicle back to the bumper/trailer hitch area.
•DO NOT run wiring near the gas tank.
•If you wish to run the harness under the
vehicle, use the supplied wire ties to
secure the wire against the frame, avoiding
moving parts / hot parts such as exhaust.
•Run the wire under and through the
vehicle whenever possible, gaining
entry into the vehicle through the
firewall
•DO NOT run wiring where it can be
snagged by road debris.
Figure 15-1
Figure 15-2
continued
AL350 Hitch-Mounted Scooter and Power Chair Lift P/N: 610-00065 Rev A

COIL ANY EXCESS
WIREHERE
DO CUT
OR SHORTEN
NOT
COIL ANY EXCESS
WIREHERE
DO CUT
OR SHORTEN
NOT
16
SECTION 2 : INSTALLER
Installation
CAUTION!
DO NOT cut or shorten the harness.
4. Once harness is run into the vehicle,
remove the pin's protective tubing.
5. Inspect the pin's retaining flanges.
They may have become deformed while
run through the vehicle. These are critical
to secure the pins inside the connector.
Adjust as needed.
6. Flip open end connector's jigned
retainer, insert pins as shown. [Figure
16-2]
Verify the wires can not be pulled out by
moderately pulling on the wires.
Be sure rubber seals are inside back of
connector and close the hinged retainer.
7. Plug connector into the lift.
8. LAST…attach red wire to the positive
terminal on the battery. [Figure 16-3]
•If the harness is too long, coil the
excess wire and secure it to the
vehicle frame/bumper with the
supplied wire ties. [Figure16-1]
RED WIRE
RED WIRE
OR
LAST
SIDE MOUNT
TOPMOUNT
RED WIRE
RED WIRE
OR
LAST
SIDE MOUNT
TOPMOUNT
Figure 16-3
B=BLACK,A=R ED
LETTERSARE
MOLDED INTO
PLASTIC
HINGED
RETAINER
A
B
BLACK WIRE
ERIWDER
Protective
tubing
CORRECT
ADJUST BY
PRYING OUT
SLIGHTLY
IF NEEDED
SEALS
3
4
5
B=BLACK,A=RED
LETTERSARE
MOLDEDINTO
PLASTIC
HINGED
RETAINER
A
B
BLACKWIRE
ERIWDER
Protective
tubing
CORRECT
ADJUSTBY
PRYINGOUT
SLIGHTLY
IFNEEDED
SEALS
3
4
5
Figure 16-2
Figure 16-1
| www.harmar.com | 800-833-0478

17
SECTION 2 : INSTALLER Installation
BROWN WIRE
VEHICLE SIDE
OR
SPLICE +12VTail ParkingLight wire
or any+12V source HOT when
vehicle'slightsare turned on,
or ignitionisin"ACC" mode.
Ground for Lamp
is tied intothe
Main Power 2 Pin
Connector
LIFT SIDE
IMPORTANT!
If the installation requires the wiring harness to run on
the underside of the vehicle, route the harness away
from the exhaust system, brake lines, fuel lines and gas
tank. Avoid pinch points and sharp edges. Avoid locating
the harness where it can be snagged by road debris.
NOTE: A standard two-contact trailer connector is
included with the lift. This is for the license plate lamp. If
your vehicle is not equipped with the proper
connector, you can use the RED WIRE to make a wire
splice and achieve the same result. [Figure17-3]
TECH NOTE: MOTOR TESTING
Troubleshooting with a test light
or voltage meter may give a false
indication.
When you probe for 12 volts, the
reading may indicate a connection,
even if the connection is not
necessarily sufficient. The lift’s motor
can draw up to 20 amps at some
points, requiring all of the available
wire to flow proper current. Poor
connections are the #1 problem
associated with a slow, intermittent,
warm, poorly performing motor which
will also deteriorate prematurely.
If a single strand of a multi-strand wire
is making contact, 12V will appear on
a meter or test light, but it will not
allow the motor to operate. It is always
best to test both current and voltage,
or run the motor with known good
shop battery or power source when
troubleshooting.
Figure 17-3
AL350 Hitch-Mounted Scooter and Power Chair Lift P/N: 610-00065 Rev A

18
SECTION 2 : INSTALLER
Installation
VEHICLE HITCH
Outside Lifts require a vehicle that can accept a
Class 2 or 3 hitch. The vehicle should be wired
with a standard 4 connector trailer wiring.
If you are not sure about the vehicle and
hitch capability, contact a local hitch installer
or you can visit web sites of a hitch company.
For example: www.hitch-web.com;
www.reeseprod.com; www.draw-tite.com
Be sure to use a hitch installer that is reputable,
insured, andcapable. Their work reflects directly
on the customer’s perception ofyour mobility
lift installation.
1. Calculate the weights of the lift,
mobility device, and, where applicable,
the Swing-Away option. Be certain that
the total weight does not exceed the hitch’s
recommended tongue weight. A range of
hitches are available, capable of bearing
different amounts of weight.
The lift manufacturer suggests the installer
observe the vehicle’s Gross Vehicle Weight Rating
restrictions.
Some states have strict license plate
obstruction laws. Familiarize yourself with
local and state laws.
2. Ensure the receiver tube of the hitch is
installed parallel to the ground. This is a
requirement, not merely a recommendation.
If the hitch is not installed properly it affects
the lift’s functionality.
Some vehicles will require that the rear
suspension be supplemented. The manufacturer
recommends the installer contact a suspension
specialist for additional technical support.
A vehicle with a Class 2 hitch requires optional
accessories.
A vehicle with a Class 3 hitch and standard 4
connector wiring is ready for installation.
NOTE: Not every vehicle is capable of
having a hitch installed.
adapters. Hitch Expanders
and Extenders are strictly
prohibited – using them or any
other aftermarket accessory
may result in damage to the
vehicle, lift, and/or personal
injury to the user.
| www.harmar.com | 800-833-0478

AL1265
4” Drop Class 2
AL1235
5” Drop Class 3
H128
Class 2 Short AL127 Class 2 Extralong
AL126
Standard Class2
AL1232
2” Drop Class 3
H124
Class 3 Short AL125
Class 3 Extralong
AL123
Standard Class 3
AL1265
4” Drop Class 2
AL1235
5” Drop Class 3
H128
Class 2 Short AL127 Class 2 Extralong
AL126
Standard Class2
AL1232
2” Drop Class 3
H124
Class 3 Short AL125
Class 3 Extralong
AL123
Standard Class 3
1-1/4"
1-1/4"
CLASS2
2"
2"
CLASS3
1-1/4"
1-1/4"
CLASS2
2"
2"
CLASS3
Bumper distance is the length from the
trailer hitch's bolt hole to the rear most
point on the vehicle.
Hitch Height is the distance from
reviecerhctihehtfomottobeht
to the ground
BUMPER
DISTANCE
HITCH
HEIGHT
GROUND
Bumper distance is the length from the
trailer hitch's bolt hole to the rear most
point on the vehicle.
Hitch Height is the distance from
reviecerhctihehtfomottobeht
to the ground
BUMPER
DISTANCE
HITCH
HEIGHT
GROUND
H128
Class2Short
H124
Class 3 Short
X
For shallow hitches,
ex.Spare Tire blocked hitches,
a short Hitch Adapter
maybe required.
SOME
AL126
Standard Class2
AL123
Standard Class3
X=0-7.5" X=7.5"-10" X=10"-13.5"
AL127
Class2Extra long
AL125
Class3Extra long AL125 Class3Extra long
3SSALC
2SSALC
Pleasecontact
Harmar's Technical
ServiceDept.
IF:
H128
Class2Short
H124
Class 3 Short
X
For shallow hitches,
ex.Spare Tire blocked hitches,
a short Hitch Adapter
maybe required.
SOME
AL126
Standard Class2
AL123
Standard Class3
X=0-7.5" X=7.5"-10" X=10"-13.5"
AL127
Class2Extra long
AL125
Class3Extra long AL125 Class3Extra long
3SSALC
2SSALC
Pleasecontact
Harmar's Technical
ServiceDept.
IF:
19
SECTION 2 : INSTALLER Installation
HITCH ADAPTERS
The Hitch Adapter plugs into the
vehicle’s trailer hitch and serves
as the interface between the
lift and vehicle. Hitch adapters
are designed for the needs of
different vehicles. Some are
shown in. [Figure19-1]
Selecting a Hitch Adapter
To determine the Hitch Adapter
that will ensure proper lift
operation, first determine the
Hitch Class. Measure the Bumper
Distance and the Hitch Height.
[Figure 19-2]
NOTE: Some shallow hitches, ex. Spare tire blocked hitches,
may require a short Hitch Adapter. [Figure 19-4]
Figure 19-3
Figure 19-1
Figure 19-2
WARNING!
Harmar lifts
require Harmar-
approved hitch
adapters. Hitch Expanders
and Extenders are strictly
prohibited – using them or any
other aftermarket accessory
may result in damage to the
vehicle, lift, and/or personal
injury to the user.
Hitch Class is usually printed on the
trailer hitch. You can also determine
it by measuring the inside of the
receiver on the trailer hitch as
shown. [Figure 19-3]
AL350 Hitch-Mounted Scooter and Power Chair Lift
Figure 19-4
P/N: 610-00065 Rev A

THGIEHHCTIH
CONFIGURATOR
X
HCTIH2SSALCHCTIH3SSALC
6”
7”
8”
9”
10”
11”
12”
13”
14”
15”
16”
17”
18”
19”
20”
21”
22”
23”
24”
25”
26”
6”
7”
8”
9”
10”
11”
12”
13”
14”
15”
16”
17”
18”
19”
20”
21”
22”
23”
24”
25”
26”
6”
7”
8”
9”
10”
11”
12”
13”
14”
15”
16”
17”
18”
19”
20”
21”
22”
23”
24”
25”
26”
6”
7”
8”
9”
10”
11”
12”
13”
14”
15”
16”
17”
18”
19”
20”
21”
22”
23”
24”
25”
26”
2”
2”
5”
5”
AL-123/HD
AL-126
AL-123 /HD2
AL-1265
AL-123 /HD5
AL-123 /HD5
AL-123 /HD2
AL-1265
STANDARD
STANDARD
STANDARD
STANDARD
AL-123/HD
AL-126
if =Xif =Xif =Xif =X
PLEASE CONTACT
TECHNICAL SERVICE
DEPARTMENT FOR
AVAILABILITYOF
LARGER DROP
ADAPTERS
PLEASE CONTACT
TECHNICAL SERVICE
DEPARTMENT FOR
AVAILABILITYOF
LARGER DROP
ADAPTERS
PLEASE CONTACT
TECHNICAL SERVICE
DEPARTMENT FOR
AVAILABILITYOF
LARGER DROP
ADAPTERS
PLEASE CONTACT
TECHNICAL SERVICE
DEPARTMENT FOR
AVAILABILITYOF
LARGER DROP
ADAPTERS
STANDARD MOUNT
AL107 HITCH POST
(NO SWING-AWAY)
STANDARD MOUNT
AL107 HITCH POST
(NO SWING-AWAY)
SWING-AWAY
(OPTIONAL)
SWING-AWAY
(OPTIONAL)
20
SECTION 2 : INSTALLER
Installation
HITCH ADAPTERS (Con’t)
The effective range of the Hitch Adapter
changes slightly if the lift is equipped
with the standard AL107 Hitch Post.
[Figure 19-1] or if it’s equipped with a
tail gate/hatch accessibility option,
either the AL105 or AL105LSwing-
Away. [Figure 20-2]
If the measurement falls in between, ex. 18 - ½", round up if greater than or equal to ½", round down if less than ½". Combination Hitch Adapters are
available ( ex. Short Class 3, 5" Drop or Long Class 2, 2" Drop)
If you have any questions / concerns about selecting the appropriate Hitch Adapter for your application,
please contact Harmar's Technical Service Department, and a trained representative will be glad to help.
Figure 20-1
Figure 20-2
| www.harmar.com | 800-833-0478