Hawking HW12ACM User manual

website www.hawkingtech.com
e-mail [email protected]
©COPYRIGHT 2015 HAWKING TECHNOLOGIES,INC. ALL RIGHTS RESERVED.
USER’S MANUAL

Wireless-1200AC Managed AP Pro HW12ACM

COPYRIGHT
Copyright ©2015 by Hawking Technologies. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of this company
Hawking Technologies makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not Hawking Technologies, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Further, this company reserves the right to revise this publication
and to make changes from time to time in the contents thereof without obligation to notify any person of
such revision or changes.

Federal Communication Commission
Interference Statement
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This equipment must be installed and operated in accordance with provided instructions and a minimum 20
cm spacing must be provided between computer mounted antenna and person’s body (excluding
extremities of hands, wrist and feet) during wireless modes of operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the authority to operate equipment.
Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order
to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the
antenna shall not be less than 20cm (8 inches) during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal
Equipment and the mutual recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal
Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at
all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland,
France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the
United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein,
Norway, and Switzerland.
EU Countries Not intended for use
None.

CONTENTS
Chapter 1 - Product Information.................................................................. 2
1-1. Package Contents ............................................................................................................................. 2
1-2. System Requirements....................................................................................................................... 2
1-3. Hardware Overview.......................................................................................................................... 3
1-4. LED Status......................................................................................................................................... 4
1-5. Reset................................................................................................................................................. 4
1-6. Safety Information............................................................................................................................ 5
Chapter 2 - Quick Setup .............................................................................. 6
2-1. Initial Setup....................................................................................................................................... 6
2-2. Quick Setup Settings......................................................................................................................... 9
Chapter 3 - Hardware Installation ..............................................................12
3-1. Connecting the access point to a router or PoE switch ................................................................. 12
3-2. Mounting the access point to a ceiling .......................................................................................... 13
3-3. T-Rail Mount................................................................................................................................... 16
Chapter 4 - Browser Based Configuration Interface ....................................18
4-1. Information..................................................................................................................................... 20
4-1-1. System Information............................................................................................................. 20
4-1-2. Wireless Clients................................................................................................................... 24
4-1-3. Wireless Monitor................................................................................................................. 26
4-1-4. Log ....................................................................................................................................... 28
4-2. Network Settings ............................................................................................................................ 30
4-2-1. LAN-Side IP Address ............................................................................................................ 30
4-2-2. LAN Port .............................................................................................................................. 32
4-2-3. VLAN.................................................................................................................................... 33
4-3. Wireless Settings ............................................................................................................................ 34
4-3-1. 2.4GHz 11bgn ...................................................................................................................... 34
4-3-2. 5GHz 11ac 11an................................................................................................................... 47
4-3-3. WPS ..................................................................................................................................... 53
4-3-4. RADIUS ................................................................................................................................ 55
4-3-5. MAC Filter............................................................................................................................ 57
4-3-6. WMM .................................................................................................................................. 59
4-4. Management .................................................................................................................................. 61
4-4-1. Admin .................................................................................................................................. 61
4-4-2. Date and Time ..................................................................................................................... 64

4-4-3. Syslog Server ....................................................................................................................... 66
4-4-4. I’m Here............................................................................................................................... 67
4-5. Advanced........................................................................................................................................ 68
4-5-1. LED Settings......................................................................................................................... 68
4-5-2. Update Firmware ................................................................................................................ 69
4-5-3. Save/Restore Settings ......................................................................................................... 70
4-5-4. Factory Default.................................................................................................................... 72
4-5-5. Reboot................................................................................................................................. 73
Chapter 5 - Appendix .................................................................................74
5-1. Configuring your IP address ........................................................................................................... 74
5-1-1. Windows XP......................................................................................................................... 75
5-1-2. Windows Vista..................................................................................................................... 77
5-1-3. Windows 7........................................................................................................................... 79
5-1-4. Windows 8.1........................................................................................................................ 82
5-1-5. Mac...................................................................................................................................... 85
5-2. Hardware Specification .................................................................................................................. 87
5-3. Environmental and Physical ........................................................................................................... 87
5-4. Glossary .......................................................................................................................................... 87

2
Chapter 1 - Product Information
1-1. Package Contents
1. HW12ACM
2. Ceiling Mount Bracket
3. T-Rail Mounting Kit &
Screws
4. Quick Installation Guide
5. Power Adapter 12V/1A
1-2. System Requirements
-Existing cable/DSL modem & router
-Computer with web browser for access point configuration
2
8
4
4
1
1
3
2
5

3
1-3. Hardware Overview
Ethernet Port
Power Jack (DC IN)

4
1-4. LED Status
LED Color
LED Status
Description
Blue
On
The access point is starting up.
Purple
On
The access point is on.
Amber
Flashing
Error.
Off
Off
The access point is off.
1-5. Reset
If you experience problems with your access point, you can reset the device back to its factory settings. This
resets all settings back to default.
1. Press and hold the reset button on the access point for at least 20 seconds then release the button.
You may need to use a pin or similar sharp object to push the reset button.
2. Wait for the access point to restart. The access point is ready for setup when the LED is Purple.

5
1-6. Safety Information
In order to ensure the safe operation of the device and its users, please read and act in accordance with the
following safety instructions.
1. The access point is designed for indoor use only; do not place the access point outdoors.
2. Do not place the access point in or near hot/humid places, such as a kitchen or bathroom.
3. Do not pull any connected cable with force; carefully disconnect it from the access point.
4. Handle the access point with care. Accidental damage will void the warranty of the access point.
5. The device contains small parts which are a danger to small children under 3 years old. Please keep the
access point out of reach of children.
6. Do not place the access point on paper, cloth, or other flammable materials. The access point may
become hot during use.
7. There are no user-serviceable parts inside the access point. If you experience problems with the access
point, please contact your dealer of purchase and ask for help.
8. The access point is an electrical device and as such, if it becomes wet for any reason, do not attempt to
touch it without switching the power supply off. Contact an experienced electrical technician for further
help.
9. If you smell burning or see smoke coming from the access point or power adapter, then disconnect the
access point and power adapter immediately, as far as it is safely possible to do so. Call your dealer of
purchase for help.

6
Chapter 2 - Quick Setup
Your access point can be up and running in just a few minutes. This quick installation guide will help to set
up your access point and configure its basic settings. Please follow the instructions in the chapters below:
2-1. Initial Setup
1. Connect the access point to a computer via Ethernet cable.
2. Connect the power adapter to the access point’s 12VDC port and plug the power adapter into a power
supply using the included cable.
3. Please wait a moment for the access point to start up. The access point is ready when the LED is
Purple.
4. Set your computer’s IP address to 192.168.1.x where xis a number in the range 1 –100. If you are
unsure how to do this, please refer to the Chapter 5-1.
Please ensure there are no other active network connections on your computer
(disconnect Wi-Fi connections and Ethernet cables).
5. Enter the access point’s default IP address 192.168.1.230 into the URL bar of a web browser.

7
6. You will be prompted for a username and password. Enter the default username “admin” and the
default password “1234”.
7. You will arrive the “Quick Setup” screen shown below.

8
8. Next, please follow the instructions below in 2-2. Quick Setup to configure the access point’s basic
settings.
For more advanced configurations, please refer to Chapter 4. Browser Based
Configuration Interface.

9
2-2. Quick Setup Settings
The instructions below will help you to configure the following basic settings of the access point:
12.4GHz & 5GHz SSID LAN IP Address
2LAN IP Address
32.4GHz & 5GHz SSID Security
It is recommended you configure these settings before using the access point.
1. To change the SSID of your access point’s 2.4GHz wireless network(s), go to “2.4GHz Basic Settings”.
Enter the new SSID for your 2.4GHz wireless network in the “SSID1” field”. The default 2.4GHz SSID is
“Hawking_HW12ACM_2.4GHz”
To utilize multiple 2.4GHz SSIDs, open the drop down menu labelled “Enable SSID
number” and select how many SSIDs you require. Then enter a new SSID in the
corresponding numbered fields below, before clicking “Apply”.
2.Go to “5GHz Basic Settings” and repeat step 1 for the access point’s 5GHz AC wireless network. The
default 5GHz SSID is “Hawking_HW12ACM_5GHz”

10
3.To change the access point’s LAN IP address, go to “LAN-side IP Address” and you will see the screen
below.
4. Enter the IP address settings you wish to use for your access point. You can use a dynamic (DHCP) or
static IP address, depending on your network environment. Click “Next” to save the changes and to go
to the security settings.
When you change your access point’s IP address, you need to use the new IP address
to access the browser based configuration interface instead of the default IP
192.168.1.230.

11
5. To configure the security of your access point’s 2.4GHz wireless network(s), go to “2.4GHz Wireless
Security Settings”. Select an “Authentication Method” and enter a “Pre-shared Key” or “Encryption
Key” depending on your choice, then click “Apply”. Hawking recommends at least WPA/WPA2
security.
If using multiple SSIDs, specify which SSID to configure using the “SSID” drop down
menu.
6. Go to “5GHz Wireless Security Settings and repeat steps 5 for the access point’s 5GHz wireless
network. Click “Apply” and the device will now reset and save your settings.
7. The basic settings of your access point are now configured. Please refer to Chapter 3 - Hardware
Installation for guidance on connecting your access point to a router or PoE switch.

12
Chapter 3 - Hardware Installation
3-1. Connecting the access point to a router or PoE switch
1. If you need to, remove the cap from the underside of the access point. This creates extra space for
your cables to pass through.
2. Connect a router or PoE switch to the access point’s LAN port using an Ethernet cable.
3. If you are using a router, then connect the power
adapter to the access point’s 12V DC port and plug
the power adapter into a power supply.
Do not use the power adapter if you are
using a PoE switch.

13
3-2. Mounting the access point to a ceiling
To mount the access point to a ceiling, please follow the instructions below and refer to diagram A& B.
For Wooden Ceilings (refer to diagram A):
1. Place the ceiling mount bracket to a ceiling in your desired location and insert screw iii through hole i
(x 2)and tighten to fix the bracket in place.
2. When the ceiling bracket is in place, inset screw iv into hole v(x 2) on the access point.
3. Fix the access point to the ceiling bracket by inserting the attached screws iv into hole vi and twisting
the access point.
4. Lock the access point firmly into place when by twisting it to align screws iv with the grooves in the
ceiling mount.
For Other Ceilings (refer to diagram B):
1. Place the ceiling mount bracket to a ceiling in your desired location and Insert screw ii through hole i (x
2) and tighten to fix the bracket in place, as shown in A.
2. Insert screw iii through hole iand into the rear of screw ii and tighten to provide additional strength.
3. When the ceiling bracket is in place, insert screw iv into hole v(x 2) on the access point.
4. Fix the access point to the ceiling bracket by inserting the attached screws iv into hole vi and twisting
the access point.
5. Lock the access point firmly into place by twisting it to align screws iv with the grooves in the ceiling
mount.

14
A
i
ii
iii

15
B