Hawking HW9ACM User manual

website www.hawkingtech.com
e-mail [email protected]
©COPYRIGHT 2015 HAWKING TECHNOLOGIES,INC. ALL RIGHTS RESERVED.
USER’S MANUAL

Wireless-1200AC Multifunction AP/BRIDGE/REPEATER HW9ACM

COPYRIGHT
Copyright ©2015 by Hawking Technologies. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written permission of this company
Hawking Technologies makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following their
purchase, the buyer (and not Hawking Technologies, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the
right to revise this publication and to make changes from time to time in the contents
thereof without obligation to notify any person of such revision or changes.

Federal Communication Commission
Interference Statement
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This equipment must be installed and operated in accordance with provided instructions
and a minimum 20 cm spacing must be provided between computer mounted antenna and
person’s body (excluding extremities of hands, wrist and feet) during wireless modes of
operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

Any changes or modifications not expressly approved by the party responsible for
compliance could void the authority to operate equipment.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches)
during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE
EUROPEAN PARLIAMENTAND THE COUNCIL of March 9, 1999 on radio
equipment and telecommunication terminal Equipment and the mutual recognition of
their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment)As of
April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and
use it. However, special attention must be paid to the dangers of electric shock and static
electricity when working with electrical equipment. All guidelines of this and of the
computer manufacture must therefore be allowed at all times to ensure the safe use of the
equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium,
Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the
Netherlands, Portugal, Spain, Sweden, and the United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states:
Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries Not intended for use
None.

CONTENTS
Chapter I: Product Information................................................................2
1-1 Product Introduction........................................................................................... 2
1-2 Safety Information............................................................................................... 3
1-3 System Requirements........................................................................................... 4
1-4 Package Contents................................................................................................. 5
1-5 Product Overview................................................................................................. 6
Chapter II: Quick Setup and Basic Settings.............................................8
2-1 Installing the HW12ACM.................................................................................... 8
2-2 Connecting to the HW9ACM by Web Browser................................................... 9
2-2-1 Windows 95/98/Me IP Address Setup: ........................................................... 10
2-2-2 Windows 2000 IP Address Setup.................................................................... 12
2-2-3 Windows XP IP Address Setup ....................................................................... 14
2-2-4 Windows Vista/7/8 IP Address Setup.............................................................. 16
2-2-5 Mac OS X IP Address Setup........................................................................... 18
2-2-6 Tablet/Smartphone Setup................................................................................ 19
2-2-7 Connecting to Web Management Interface.................................................... 21
2-3 ‘Quick Setup’...................................................................................................... 23
2-3-1 Setup Procedure for ‘Repeater’ ..................................................................... 25
2-3-2 Setup Procedure for ‘Router’......................................................................... 29
2-3-3 Setup Procedure for ‘Access Point’ ............................................................... 34
2-3-4 Setup Procedure ‘Bridge’............................................................................... 39
2-3-5 Setup procedure for ‘Bridge-Point to Point’: ................................................ 43
2-3-6 Setup procedure for ‘Bridge-Point to Multi-Point’........................................ 49
2-3-7 Setup Procedure for ‘Bridge WDS’................................................................ 55
Chapter III General Setup.......................................................................60
3-1 Time zone and time auto-synchronization.......................................................... 61
3-2 Change Management password.......................................................................... 63
3-3 Remote Management.......................................................................................... 65
3-4 Setup Internet Connection (WAN Setup) ........................................................... 67
3-4-1 Setup Procedure for ‘Dynamic IP’: ............................................................... 69
3-4-2 Setup Procedure for ‘Static IP’:..................................................................... 70
3-4-3 Setup Procedure for ‘PPPoE’:....................................................................... 71
3-4-4 Setup Procedure for ‘DNS’:........................................................................... 73
3-4-5 Setup Procedure for ‘DDNS’:........................................................................ 76
3-5 Wired LAN Configuration.................................................................................. 78

3-5-1 Local Network................................................................................................ 79
3-5-2 DHCP Server ................................................................................................. 80
3-5-3 Static DHCP Leases Table ............................................................................. 81
3-6 Wireless Network ............................................................................................... 83
3-6-1 Basic Wireless Settings................................................................................... 84
3-6-1-1 Access Point............................................................................................. 84
3-6-1-2 Bridge (Station Infrastructure)................................................................. 89
3-6-1-3 AP Bridge-Point to Point.......................................................................... 90
3-6-1-4 AP Bridge-Point to Multi-Point ............................................................... 93
3-6-1-5 AP Bridge-WDS....................................................................................... 95
3-6-1-6 Universal Repeater................................................................................... 97
3-6-2 Advanced Wireless Settings.......................................................................... 100
3-6-3 Security Settings........................................................................................... 103
3-6-3-1 Disable wireless security........................................................................ 103
3-6-3-2 WEP - Wired Equivalent Privacy........................................................... 103
3-6-3-3 Wi-Fi Protected Access (WPA):............................................................. 106
3-6-3-4 WPA RADIUS ....................................................................................... 107
3-6-4 Wireless Access Control ................................................................................110
3-6-5 Wi-Fi Protected Setup (WPS)........................................................................113
3-6-6 Security Tips for Wireless Network ...............................................................116
3-7 Quality of Service (QoS)...................................................................................117
3-7-1 Basic QoS Settings........................................................................................117
3-7-2 Add a new QoS rule...................................................................................... 120
3-8 Network Address Translation (NAT)................................................................ 122
3-8-1 Basic NAT Settings (Enable or disable NAT function)................................. 123
3-8-2 Port Forwarding .......................................................................................... 124
3-8-3 Virtual Server............................................................................................... 127
3-8-4 Port Mapping for Special Applications........................................................ 130
3-8-5 UPnP Setting................................................................................................ 133
3-8-6 ALG Settings ................................................................................................ 134
3-9 Firewall............................................................................................................. 136
3-9-1 Access Control.............................................................................................. 137
3-9-1-1 Add PC................................................................................................... 140
3-9-2 URL Blocking............................................................................................... 143
3-9-3 DoS Attack Prevention ................................................................................. 146
3-9-3-1 DoS - Advanced Settings....................................................................... 148

3-9-4 Demilitarized Zone (DMZ)........................................................................... 150
Chapter IV Status and Tools..................................................................153
4-1 System Status.................................................................................................... 153
4-1-1 System information and firmware version ................................................... 153
4-1-2 Internet Connection Status........................................................................... 153
4-1-3 Local Network.............................................................................................. 154
4-1-4 System Log ................................................................................................... 156
4-1-5 Security Log ................................................................................................. 156
4-1-6 Active DHCP client list................................................................................ 157
4-1-7 Statistics ....................................................................................................... 159
4-2 Configuration Tools.......................................................................................... 160
4-3 Firmware Upgrade............................................................................................ 162
4-4 Reset and Reboot.............................................................................................. 164
Chapter V: Appendix..............................................................................165
5-1 Hardware Specification................................................................................... 165
5-2 Troubleshooting............................................................................................... 166
5-3 Glossary............................................................................................................ 169

2
Chapter I: Product Information
1-1 Product Introduction
Thank you for purchasing the Hawking HW9ACM Wireless-1200AC Multifunction
AP/Bridge/Repeater
Easy installation procedures allow any computer user to setup a network in very short
time - within minutes, even inexperienced users. Just follow the instructions given in this
user manual, you can complete the setup procedure and unleash the power of this
HW9ACM all by yourself!
Other features of the Wireless-1200AC Multifunction AP/Bridge/Repeater include:
7 different Wireless Modes: Repeater, Router, Access Point, Bridge Client,
Bridge Point to Point, Bridge Point to Multi-Point and AP Bridge WDS modes
Supports 2.4GHz and 5GHz wireless devices simultaneously.
Provides IEEE 802.11A/B/G/N/AC wireless LAN capability
Supports 64/128-bit WEP, WPA, and WPA2 wireless data encryption.
Supports MAC address filtering (Only allow specific wireless device of your
choice to connect to this access point).
Four wired LAN ports (10/100/1000M)
One Wired WAN port (10/100/1000M)
Auto MDI / MDI-X function for all wired Ethernet ports.
Support DHCP (Server/Client) for easy IP-address setup.
Allows you to monitor the access point’s status: DHCP Client Log, System Log,
Security Log and Device/Connection Status.
Easy to use Web-based GUI for network configuration and management purposes.

3
1-2 Safety Information
In order to keep the safety of users and your properties, please follow the following safety
instructions:
1. This HW9ACM is designed for indoor use only; DO NOT place this HW9ACM
outdoors.
2. DO NOT put this HW9ACM near hot or humid places, like a kitchen or bathroom.
Also, do not leave this HW9ACM in the car.
3. DO NOT pull any connected cable with force; disconnect it from the HW9ACM first.
4. If you want to place this HW9ACM at high places or hang on the wall, please make
sure the HW9ACM is firmly secured. Falling from high places would damage the
HW9ACM and its accessories, and void the warranty.
5. Accessories of this HW9ACM, like the antenna and power supply, are dangerous to
small children under 3 years old. They may put the small parts in their nose or mouth and
it could cause serious damage to them. KEEP THIS HW9ACM OUT THE REACH OF
CHILDREN!
6. The HW9ACM will become hot when being used for a long time (This is normal and
is not a malfunction). DO NOT put this HW9ACM on paper, cloth, or other flammable
materials.
7. There’s no user-serviceable part inside the HW9ACM If you found that the HW9ACM
is not working properly, please contact your dealer of purchase and ask for help. DO
NOT disassemble the HW9ACM, or the warranty will be void.
8. If the HW9ACM falls into water when it’s powered, DO NOT use your hand to pick it
up. Switch the electrical power off before you do anything, or contact an experienced
electrical technician for help.
9. If you smell something strange or even see some smoke coming out from the
HW9ACM or power supply, remove the power supply or switch the electrical power off
immediately, and call dealer of purchase for help.

4
1-3 System Requirements
Computer or network device(s) with wired or wireless network interface card.
Web browser (Microsoft Internet Explorer 4.0 or above, Netscape Navigator 4.7
or above, Opera web browser, Mozilla Firefox web browser or Safari web
browser).
An available AC power socket (100 –240 V, 50/60Hz)

5
1-4 Package Contents
Before you start to use this HW9ACM, please check if there is anything missing in the
package. Contact your place of purchase to claim missing items:
1x –HW9ACM Wireless-1200AC Multifunction AP/Bridge/Repeater
1x - Quick Installation Guide
1x - A/C power adapter
1x - Ethernet cord
1x - Setup CD

6
1-5 Product Overview
Top Panel
LED Name
Light Status
Description
PWR
On
Router is switched on and correctly powered.
2.4G
On
2.4GHz Wireless WPS function is enabled.
Off
2.4GHz Wireless network is switched off.
Flashing
2.4GHz Wireless LAN activity (transferring
or receiving data).
5G
On
5GHz Wireless WPS function is enabled.
Off
5GHz Wireless network is switched off.
Flashing
5GHz Wireless LAN activity (transferring or
receiving data).
LAN 1-4
LNK/ACT
On
LAN port is connected.
Off
LAN port is not connected.
Flashing
LAN activity (transferring or receiving data).
WAN
LNK/ACT
On
WAN port is connected.
Off
WAN port is not connected.
Flashing
WAN activity (transferring or receiving data).
Back Panel
Item Name
Description
Reset / WPS
Reset the router to factory default settings (clear all settings) or
start WPS function. Press this button and hold for 10 seconds to
restore all settings to factory defaults; press this button for less
than 5 seconds once to start 2.4GHz & 5GHz wireless WPS

7
function.
1 –4
LocalArea Network (LAN) ports 1 to 4.
WAN
Wide Area Network (WAN / Internet) port.
Power Jack
Power connector, connects to 12V/1A power adapter.

8
Chapter II: Quick Setup and Basic Settings
2-1 Installing the HW12ACM
Complete the following instructions to build the network connection between your new
wireless HW9ACM and your computers or network devices:
1. Connect the A/C power adapter to the wall socket, and then connect it to the ‘Power’
socket of the HW9ACM.
2. Connect the HW9ACM to your computer (source) through the LAN port of the
HW9ACM by Ethernet cable or connect to it wirelessly.
3. Please check all LEDs on the front panel. LAN LEDs should be on if the HW9ACM
is correctly connected. If it is not on, or any LED you expect is not on, please recheck
the cabling, or jump to ‘5-2 Troubleshooting’ for possible reasons and solutions.

9
2-2 Connecting to the HW9ACM by Web Browser
After your HW9ACM Hi-Gain™ Wireless-AC Multi-Function Access Point / Bridge has
been connected and powered the next step is to access the Web Menu for initial
configuration. To do this, your computer must be able to get an IP address
automatically (use dynamic IP address setting).
Try to access: http://192.168.1.230
If the Web Menu appears you can skip the next steps and go to step 2-3. You will need
to enter the following default login and password to access the ‘Quick Setup’menu:
Login: admin
Password: 1234
If it’s set to use a static IP address or you are unsure, please follow the following
instructions to configure your computer to use a dynamic IP address:
Note: Please be sure to set your network IPaddresses back to default after you have
finished configuration.
If the operating system of your computer is….
Windows 95/98/Me - please go to section 2-2-1
Windows 2000 - please go to section 2-2-2
Windows XP - please go to section 2-2-3
Windows Vista/7/8 - please go to section 2-2-4
Mac OS X - please go to section 2-2-5

10
2-2-1 Windows 95/98/Me IP Address Setup:
1. Click ‘Start’button (it should be located at lower-left corner of your computer), then
click control panel. Double-click Network icon, and Network window will appear.
Select ‘TCP/IP’, then click ‘Properties’.
2. Select ‘Obtain an IP address from a DHCP server’ and then click ‘OK’.

11

12
2-2-2 Windows 2000 IP Address Setup
1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then
click control panel. Double-click Network and Dial-up Connections icon; click Local
Area Connection, and Local Area Connection Properties window will appear. Select
‘Internet Protocol (TCP/IP)’ and then click ‘Properties’
2. Select ‘Obtain an IP address automatically’and ‘Obtain DNS server address
automatically’, then click ‘OK’.

13