Haws 3600 Guide

02/19 Models 3600/3601/3602/3603/3610/3611/3612/3620/3621/3630/3601FR/ Page 1 of 10
3602FR/3603FR/3610FR/3611FR/3612FR/3620FR/3621FR/3630FR
1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]
E-mail: [e-mail]  website: www.hawsco.com
No. 0510000704 (2)
Modular Outdoor Fountain System
MODELS 3600/3601/3602/3603/3610/3611/3612/3620/3621/3630/3601FR/
3602FR/3603FR/3610FR/3611FR/3612FR/3620FR/3621FR/3630FR
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that this specific product is guaranteed against defective material or
poor workmanship for a period of one year from date of shipment. HAWS liability
under this warranty shall be discharged by furnishing without charge F.O.B. HAWS
Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS, Sparks,
Nevada. HAWS will not be liable for any damages caused by defective materials or
poor workmanship, except for replacements, as provided above. Buyer agrees that
HAWS shall not be liable for general, special, or consequential damages claimed to
arise under the contract of sale. The drinking fountain manufactured by HAWS is
warranted to function if installation and maintenance instructions provided are
adhered to. The units also must be used for the purpose for which they were
intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

02/19 Models 3600/3601/3602/3603/3610/3611/3612/3620/3621/3630/3601FR/ Page 2 of 10
3602FR/3603FR/3610FR/3611FR/3612FR/3620FR/3621FR/3630FR
RECOMMENDED TOOLS: Hack saw, PVC solvent weld glue, screwdriver, level, 12"
adjustable wrench, 10" pipe wrench, 1/8” or 5/32” tamper-resistant hex key wrench (supplied),
9/16”, 1/2", 7/16” socket wrench or open- end wrench.
LOCATION OF UNIT: The Model 36XX/36XXFR Modular Fountain System can be assembled
to be wheelchair accessible. When the pedestal arm is installed in the high orientation, the
height dimensions shown on the model specification sheet meet current ADA requirements.
When installing this unit, local, state or federal codes should be adhered to. If height other
than shown is required, then dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet is 3/8“O.D. quick-connect fitting. Waste outlet is female 1-
1/2” PVC pipe. Plumbing connections vary depending on how the unit is configured during
assembly. The pedestal (3674/3675) is supplied with various fittings and PVC pipe for a top
waste connection. The arm (3671/3673) is supplied with various fittings, waste tee, and elbow
for a side arm waste connection. If two arms are attached to the pedestal at the same height,
a 1-1/2” PVC cross is required (not supplied) for connecting the waste lines.
MAINTENANCE:
For 36XX models- Periodically clean the pushbutton strainer. Refer to 5874 Series Valve
Operation and Maintenance Sheet for more information.
For 36XXFR models- Refer to 6518 Operation and Maintenance Sheet for more information.
INSTALLATION PROCEDURE
The 36XX Modular Outdoor Drinking Fountain is a system in interchangeable components that
can be installed in the configuration best suited to the installation site. The fountain can re-
configured after installation as desired. Follow the installation procedures outlined in the
installation diagram. 36XXFR versions must be connected to 6518 series freeze resistant bury
valve. See 6518 installation manual for instructions.
GENERAL NOTES:
1. For all plastic push-in type fitting connections, only connect NSF-61 copper or
plastic tubing. Stainless steel or glass tubing is not recommended. The
following assembly instructions must be followed to ensure a watertight
connection:
a. Cut tubing square and clean.
b. Mark from end of tube the length of insertion (See table below).
c. Push tube into the fitting until it bottoms out.
d. To remove, depress collet and pull tubing out.
Tube Sizes
O.D.
Tolerance Insertion Depth
1/4”
±.005”
11/16”
3/8”
±.005”
3/4”
1/2”
±.005”
7/8”
5/8”
±.005”
1-1/8”

02/19 Models 3600/3601/3602/3603/3610/3611/3612/3620/3621/3630/3601FR/ Page 3 of 10
3602FR/3603FR/3610FR/3611FR/3612FR/3620FR/3621FR/3630FR
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1.
Insufficient bubbler flow
(3680/3680FR Drinking Fountain)
1a.
Verify minimum 30 psi flowing supply
pressure.
b.
For 3680- Check that inlet screwdriver
stop valve is wide open. Clean inlet
strainer or adjust valve to increase
flow. See 5874 Series Valve Manual.
c.
For 3680FR- Adjust valve to increase
flow. See 6518FR Manual.
2.
Insufficient bottle filler flow
(3690/3690FR Bottle Filler)
2a.
b.
c.
Nozzle strainer is clogged. Use nozzle
removal tool to remove strainer and
replace. Replacement strainers may be
ordered by calling Customer Service.
For 3690- Check that inlet screwdriver
stop valve is wide open. Clean inlet
strainer or adjust valve to increase
flow. See 5874 Series Valve Manual.
For 3690FR- Adjust valve to increase
flow. See 6518FR Manual.
For more information about Haws products, see our website: www.hawsco.com
© 2019 Haws®Corporation – All Rights Reserved
HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation.

©
®

©
®

©
®

©
®

©
®

©
®

©
®