Henderson HUSKY Folding 25 Series User manual

HUSKY FOLDING 25 AND 40
Fitting Instructions
Kit Short Code No. of Doors Track Length Max Door Height Max Door Width Door Thickness Range Max Door Weight
HF25/12 2 1234mm 2400mm 610mm 20 - 44mm 25kg
HF25/24 2 2458mm 2400mm 610mm 20 - 44mm 25kg
HF40/15 4 1538mm 2700mm 762mm 20 - 44mm 40kg
HF40/30 4 3066mm 2700mm 762mm 20 - 44mm 40kg
1
KIT AND DOOR SPEICIFICATION
TOOLS REQUIRED
KIT CONTENTS
Hacksaw
Plumb Line
10mm and
13mm Spanners
Tape Measure
Drill + 10mm Drill Bit
Hammer
Spirit Level
Posidrive
Screwdriver
Husky Hanger
x 1 for 2 doors
x 2 for 4 doors
Steel Track x 1
Hinge
x 3 for 2 doors
x 9 for 4 doors
Guide Channel x 1
(HF40 only)
Top Pivot x 1 Bottom Pivot x 1
Guide x 2
(HF40 only)

2
SYSTEM OVERVIEW
Husky Folding 25
Husky Folding 40
HANGER END
VIEW

3
STEP BY STEP INSTRUCTIONS
STEP 1: Use a 10mm drill bit to drill a hole into the top and bottom of the pivot door on the side closest to the door frame
STEP 2: Position and secure top pivot body to the top of the pivot door
STEP 3: Fit hangers to doors - for 2 door applications fit hanger to 2nd door. For 4 door applications, fit hangers to 2nd
and 4th doors.

4
STEP 5: Attach guide to bottom of the doors (HF40 kits only)
STEP 4: Position and secure the bottom pivot body to the bottom of the pivot door.
STEP 6: Affix butt hinges
2 Door Configuration
4 Door Configuration
i. Measure 125mm from the top of the
door to identify where to fix the top of the
first hinge
ii. Screw into position
iii. Measure 150mm from the bottom of
the door to identify where to fix the
bottom of the last hinge
iv. Screw hinge into position
v. Ensure the remaining hinge measures
equal distance between the top and
bottom hinges
vi. Repeat this for the remaining doors

5
STEP 7: Measure the opening width and cut track to fit
STEP 8: Position and secure top pivot socket into track
STEP 9: Affix track into opening by the two outer points only
O = Opening width

6
STEP 10: Use a plum line to align hole centre for the top pivot to the bottom pivot plate and screw into place - this should
be 46mm from the door frame.
STEP 11 i) For HF25 kits, please skip to step 13. For HF40 kits, cut guide channel to required length.
ii) Use a plum line to align the guide channel with the track, mark out positioning with a pencil ready for routing
STEP 12: Route guide channel into floor and secure into position.
17mm
2mm
21mm
20mm
It is the installer's
responsibility to ensure the
guide channel has been
routed into the floor
appropriately.
Guide Channel Formula:
Guide channel length = opening width - 85mm

STEP 13: Unfix the non pivot side of the track and slide doors into the track. Affix the track back into position
STEP 14: Locate the bottom pivot and top pivot onto the plate
STEP 15: Adjust door height using spanners - use 13mm spanner on pivot door and 10mm spanner on hanger door
P C Henderson Ltd, Durham Road, Bowburn, Co. Durham, DH6 5NG, UK
UK Sales Export Sales
t: [phone] t: [phone]
e: [e-mail] e: [email protected]
w: www.pchenderson.com w: export.pchenderson.com
665048
LVL 06
October 2019
NOTE: When adjusting, ensure that the hanger supports the weight of the doors along with the length of the track.
UK Registered Address: P C Henderson Ltd, Durham Road, Bowburn, Co. Durham, DH6 5NG
Republic of Ireland Registered Address: P C Henderson Ltd, Westlink Industrial Estate, Kylemore Road, Dublin 10, Ireland
Holland Registered Address: Henderson Nederland BV, Rootven 14, 5531 MB, Bladel