Henny Penny ODS 300 User manual

Model ODS-300
Henny Penny
Oil Disposal
Shuttle
OPERATOR’S MANU
AL
REGISTER WARRANTY ONLINE AT WWW.HENNYPENNY.COM
(Translated Documents Available On CD within Manual)

ODS-300
LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT
Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original
purchaser only for Henny Penny appliances and replacement parts:
NEW EQUIPMENT: Any part of a new appliance, except baskets, lamps, and fuses, which proves to be defective
in material or workmanship within two (2) years from date of original installation, will be repaired or replaced
without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor. Baskets will be repaired or replaced
for ninety (90) days from date of original installation. Lamps and fuses are not covered under this Limited
Warranty. To validate this warranty, the registration card for the appliance must be mailed to Henny Penny within
ten (10) days after installation.
FILTER SYSTEM: Failure of any parts within a fryer filter system caused by the use of the non-OEM filters or
other unapproved filters is not covered under this Limited Warranty.
REPLACEMENT PARTS: Any appliance replacement part, except lamps and fuses, which proves to be defective
in material or workmanship within ninety (90) days from date of original installation will be repaired or replaced
without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor.
The warranty for new equipment covers the repair or replacement of the defective part and includes labor charges and
maximum mileage charges of 200 miles round trip for a period of one (1) year from the date of original installation.
The warranty for replacement parts covers only the repair or replacement of the defective part and does not include any
labor charges for the removal and installation of any parts, travel, or other expenses incidental to the repair or replacement of
a part.
EXTENDED FRYPOT WARRANTY: Henny Penny will replace any frypot that fails due to manufacturing or
workmanship issues for a period of up to seven (7) years from date of manufacture. This warranty shall not cover any frypot
that fails due to any misuse or abuse, such as heating of the frypot without shortening.
0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues
will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new frypot at no
cost or provide a new or reconditioned replacement fryer at no cost.
3 TO 7 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues
will be replaced at no charge for the frypot only. Any freight charges and labor costs to install the new
frypot as well as the cost of any other parts replaced, such as insulation, thermal sensors, high limits,
fittings, and hardware, will be the responsibility of the owner.
Any claim must be presented to either Henny Penny or the distributor from whom the appliance was purchased. No
allowance will be granted for repairs made by anyone else without Henny Penny’s written consent. If damage occurs during
shipping, notify the sender at once so that a claim may be filed.
THE ABOVE LIMITED WARRANTY SETS FORTH THE SOLE REMEDY AGAINST HENNY PENNY FOR ANY
BREACH OF WARRANTY OR OTHER TERM. BUYER AGREES THAT NO OTHER REMEDY (INCLUDING
CLAIMS FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES) SHALL BE AVAILABLE.
The above limited warranty does not apply (a) to damage resulting from accident, alteration, misuse, or abuse; (b) if the
equipment’s serial number is removed or defaced; or (c) for lamps and fuses. THE ABOVE LIMITED WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY
AND FITNESS, AND ALL OTHER WARRANTIES ARE EXCLUDED. HENNY PENNY NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY.
Revised 01/01/07
.
FM07-180-B
Revised 02-20-08

ODS-300
TABLE OF CONTENTS
Section Page
Section 1. INTRODUCTION ............................................................................................................1-1
1-1. Introduction.............................................................................................................1-1
1-2. Features...................................................................................................................1-1
1-3. Proper Care .............................................................................................................1-1
1-4. Assistance ...............................................................................................................1-1
1-5. Safety ......................................................................................................................1-2
Section 2. ASSEMBLY .....................................................................................................................2-1
Section 3. OPERATION....................................................................................................................3-1
Section 4. PART INFORMATION ...................................................................................................4-1
4-1. Introduction.............................................................................................................4-1
4-2. Genuine Parts..........................................................................................................4-1
4-3. How to Order ..........................................................................................................4-1
4-4. Prices.......................................................................................................................4-1
4-5. Delivery...................................................................................................................4-1
4-6. Warranty .................................................................................................................4-1
4-7. Recommended Spare Parts for Distributors............................................................4-1
I 208

ODS-300
Where information is of particular importance or is safety
related, the words NOTICE, CAUTION, or WARNING are
used. Their usage is described below:
SAFETY ALERT SYMBOL is used with DANGER,
WARNING, or CAUTION which indicates a personal
injury type hazard.
NOTICE is used to highlight especially important
information.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation
which, if not avoided, may result in property damage.
CAUTION used with the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
DANGER INDICATES AN IMMINENTLY
HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, WILL RESULT IN DEATH OR
SERIOUS INJURY.
208 1-1
SECTION 1. SAFETY

ODS-300
2-1 208
PUMP AND TUBE
ASSEMBLY PARTS.
REMOVE THESE PARTS
AND DISCARD, THEY
ARE NOT USED.
PLACE BRACKET WITH
TUBE ADAPTER OVER
THE TUBE THAT
CONNECTS TO THE
BOTTOM OF THE PUMP.
SECTION 2. ASSEMBLY

ODS-300
208 2-2
APPLY TEFLON TAPE OR
PIPE DOPE TO EVERY
PIPE CONNECTION AS
SHOWN.
ATTACH TUBE WITH
BRACKET AND ADAPTER
TO PUMP AS SHOWN.
CONNECT THE REST OF
THE TUBING TO THE PUMP
USING TEFLON TAPE OR
PIPE DOPE.
ATTACH HANDLE TO
PUMP.
PLACE PUMP AND TUBE
ASSEMBLY ON DOLLY.
BOLT BRACKET TO
HANDLE
W
ITH B
O
LT
S

ODS-300
2-3 208
TAKE BLACK PIPE
ASSEMBLY AND ATTACH
TO TOP OF PUMP AS SHOWN
USING TEFLON TAPE. TURN
UNTIL TIGHT AND LINED UP
AS SHOWN BELOW.

ODS-300
1. Remove cover from oil disposal shuttle and make sure
crumb catcher is in place.
2. Remove filter drain pan assembly from under fryer and
roll oil disposal shuttle under fryer until it stops. Make
sure drain aligns with opening in shuttle.
TO AVOID PERSONAL INJURY, BURNS,
SPILLS, AND CORROSION:
DO NOT OVERFILL. SHUTTLE HOLDS
SHORTENING FROM ONE FULLSIZE
FRYPOT OR TWO SPLIT FRYPOTS
DO NOT PUT WATER AND/OR
CLEANER IN THE SHUTTLE
3. Press and hold (on either side) until display
shows *FILTER MENU*, along with
“1.AUTO FILTER?”.
4. Press and release twice until display shows
“3.DISPOSE”. Press √button and display shows
“DISPOSE?” along with “YES NO”.
5. With oil disposal shuttle rolled into place, press & hold
√button and displays shows “DISPOSING”. Oil now
drains from the vat into the shuttle.
If oil disposal shuttle is not properly in place,
“IS DISPOSAL UNIT IN PLACE?” shows in display.
Adjust the bracket on the front of the shuttle as needed
by loosening the 4 nuts securing the bracket and
moving the bracket up or down. Once properly
adjusted, the display shows “DISPOSING”.
208 3-1
SECTION 3. OPERATION

ODS-300
6. Display shows VAT EMTY, along with “YES NO”.
Verify that vat is empty, and press √button.
7. Display shows “CLN VAT COMPLETE”, along with
“YES NO”. Once vat is clean, press √button.
8. Display shows “MANUAL FILL POT”, followed by
“VAT FULL”, along with “YES NO”. Fill the vat to
the lower indicator line on the rear of the vat and then
press √ button. Controls return to normal operation.
9. Remove the oil disposal shuttle from under fryer and
replace with the filter pan assembly.
10. Replace the cover and roll oil disposal shuttle to
disposal container.
To avoid splashing of hot shortening, make sure
cover is in place and use care when transporting hot
shortening, or burns and personal injury could
result.
11. Turn handle on pipe adapter to loosen pump assembly.
12. Swivel pump assembly over disposal container and
tighten handle on pipe adapter.
3-2 208

ODS-300
13. Turn pump handle rapidly (fast) in order to prime
the pump and to get oil to flow through pump.
To avoid damage to pump, this pump should be used for
shortening only. Do not use for water or water-based
liquids.
14. Once shuttle is empty, loosen handle on pipe adapter
and swivel pump assembly back over lower unit and
tighten handle.
To avoid burns, use care when handling the shuttle.
Some parts may be hot after pumping hot
shortening.
CLEANING
15. Daily, remove the crumb catcher and take it to a sink
and clean with soap and water. Clean the exterior of
the shuttle with a soft cloth and soap and water. It’s not
necessary to clean the interior of the unit, but if desired,
it can be wiped down with paper towels.
To avoid damage to pump, do not use water or
water-based liquids to clean the interior of the shuttle.
208 3-3

ODS-300
4-1. INTRODUCTION This section identifies and lists the replaceable parts of the Henny
Penny ODS-300, Oil Disposal Shuttle.
4-2. GENUINE PARTS Use only genuine Henny Penny parts in your unit. Using a part of
lesser quality or substitute design may result in unit damage or
personal injury.
4-3. HOW TO FIND PARTS To find items you want to order from the Parts List, proceed as
follows:
1. Refer to the exploded drawing in this section to identify the part
needed.
2. Use the item number from the exploded drawing to locate the
corresponding part in the parts list in this section. In this list will
be the Henny Penny part number and description of the part.
4-4. HOW TO ORDER PARTS Once the part you want to order has been found in the Part List,
write down the following information:
1. From the exploded drawing and Parts List (Sample)
Item Number 7
Part Number 77237
Description ASSY -COVER LVE DRAIN PAN DOLLY
2. From the data plate (Sample)
Serial Number 00100
4-5. PRICES Your distributor has a price parts list and will be glad to inform you
of the cost of yours parts order.
4-6. DELIVERY Commonly replaced items are stocked by your independent Henny
Penny distributor and will be sent out when your order is received.
Other parts will be ordered by the distributor from Henny Penny
Corporation. Normally, these will be sent to your distributor within
three working days.
4-7. WARRANTY All replacement parts (except lamps and fuses) are covered under
warranty for 90 days against manufacturing defects and workman-
ship. If damage occurs during shipping, notify the carrier at once so
that a claim may be properly filed. Refer to the warranty in this
manual for other rights and limitations.
Recommended replacement parts, stocked by your distributor, are
indicated with √ in the parts lists. Please use care when ordering
recommended parts, because all voltages and variations are
marked. Distributors should order parts based upon common
voltages and equipment sold in their territory.
4-1 208
SECTION 4. PARTS INFORMATION
4-8. RECOMMENDED
SPARE PARTS FOR
DISTRIBUTORS

ODS-300
208 4-2
1
2
3
4
5
6
9
10
7 8
11
12
13
14
15

ODS-300
Item Part
Number Number Description Qty
1 76379 ASSY – OIL SHUTTLE DRAIN PIPE 1
2 FP01-098 ELBOW – ½ NPT X 90 FEMALE BI 1
3 FP02-039 NIPPLE – ¾ X 6 LG-BI 1
4 FP02-056 NIPPLE – ¾ NPT X 18.25 INCH BI 1
5 FP01-100 ELBOW – STREET ¾ NPT BI 1
6 76583 SLEEVE – 12 X 1 ID SILICONE RBR 1
√7 77237 ASSY - COVER LVE DRAIN PAN DOLLY 1
√8 76393 ASSY – MTG BRKT AND ADPTR 1
√9 72490 PUMP – MANUAL OIL DISCARD 1
10 77242 WELD ASSY – DOLLY HANDLE 1
11 77533 BRACKET – DRAIN SW ENGAGEMENT LV 1
√12 77337 BASKET – CRUMB 1
√13 19004 CASTER 2” SWIVEL PLATE 2
14 77228 WELD ASSY – LVE DRAIN PAN DOLLY 1
√15 77815 WHEEL – 8 INCH – LVE 2
4-3 208

*FM07-180-B*Henny Penny Corp., Eaton, Ohio 45320, Revised 02-20-08
Henny Penny Corporation
P.O.Box 60
Eaton,OH 45320
1-937-456-8400
1-937-456-8402 Fax
Toll free in USA
1-800-417-8417
1-800-417-8434 Fax
www.hennypenny.com