Herman Miller Mirra 2 Instruction sheet

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BBSDT rev B.
1
YMirra 2®Back Replacement
1. Lay chair on the side. 2. Remove the D-Plug from
the retainer hole using the
small screw driver. Repeat it
for the opposite side.
Parts Included:
Steps:
Back Assembly
Small Flat Head
Screw Driver
Ratchet Wrench T40 Torx Bit
Tools Required:

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BBSDT rev B.
2
4. At the same time push the
seat upward till the knob
disengaged from seat.
Repeat it for the other side.
6. Roll the seat forward.5. Make the seat loosen
from the back.
3. Slide the at head screw
driver into the slot and
depress the spring clip.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BBSDT rev B.
3
8. Remove the trim cover.
10. Remove the handed clip,
Repeat for the opposite side.
9. Using a small at screw
driver slide into the gap to
remove oval shaped retainer
clip.
7. Using extended 2 inch
long T27 torx bit remove the
two screws at the lower
bottom.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BBSDT rev B.
4
12. Lift up on the bottom
and top at the same time to
completely take off the back
part.
14. Hook the top of the pad
over the peg and push it
down.
13. To reinstall the back pad,
ensure that each pocket has
the steel tab in it.
11. The back is hooked over
the top of the loop.
Re-assembly Steps:

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BBSDT rev B.
5
16. Reinstall the retainer
clips for the upper back.
18. Reinstall the bolt using
the extended T27 torx bits.
17. Reinstall the trim cover.
15. Flex the back around the
spine and make sure the
attachment point at the bottom
end of the hook are in place.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BBSDT rev B.
6
19. Rotate the seat back.
The bushing at the arm
should slide up into the
keyed opening on the seat.
20. Slide it down until a snap.
Repeat it for the other side.
21. Instal the D-Clips into
seat. Repeat it for the other
side.
22. Check for proper function.