Herman Miller Mirra 2 Installation instructions

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
1
Table of Content
1. Work Chair Disassembly....................................................................................3
2. Work Stool Footring Disassembly ....................................................................17
YMirra 2®Disassembly for Recycling

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
2
YMirra 2®Disassembly for Recycling
Small Flat Head
Screw Driver Ratchet Wrench T40 Torx Bit 4” T30 Torx Bit 2” T27
Torx Bit
Tools Required:
Rubber Mallet
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling codes.
Use these codes to identify material type for recycling. Non marked components
should be treated as mixed plastic. Ferrous metals can be identied using a small
magnet for recycling. Non-ferrous metals should be separated and recycled
separately.
Safety Glass

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
3
1. Lay chair on the side. 2. Remove the D-Plug from
the retainer hole using the
small screw driver. Repeat it
for the opposite side.
Steps:
Work Chair Disassembly
4. At the same time push the
seat upward till the knob
disengaged from seat.
Repeat it for the other side.
3. Slide the at head screw
driver into the slot and
depress the spring clip.
YMirra 2®Disassembly for Recycling
Work Chair Disassembly

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
4
6. Using T40 torx bit remove
the retainer bolt. Repeat it
for the other side.
5. Make the seat loosen
from the back.
8. Using at blade screw
driver pry up gently to remove
pellicle.
7. Remove the seat from
chair.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
5
9. Using at blade screw driver
pry up gently to remove seat
ring.
10. Rotate the clip upside
down. Insert the at head
screw driver into the hole and
release the tab by depressing
the clip.
11. Seat retainer clip removed. 12. Align the hole in the arm
with the arm support post.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
6
13. Using 13mm deep socket
remove the post.
16. Release the catch on the
arm.
15. Remove the washer
from arm.
14. Bolt removed from arm.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
7
17. Slide the entire assembly
up to remove the arm. 18. Use 4” T30 torx bit to remove the arm casting from
tilt assembly.
19. While loosening the bolt
pull the arm away from the
housing. The bolt head is
part of the support casting.
20. Using philips T20 torx bit
remove the front of the arm
pad bolt.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
8
21. Lift up the arm pad and
slide it off. 22. Using philips T20 torx bit
remove the single screw in
the center.
Note: The single center screw
will not be visible if the arm
pad is in the inboard position.
23.Arm pad support removed.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
9
25. Remove the trim cover.24. Using extended 2 inch
long T27 torx bit remove the
2 screws at the lower bottom.
27. Remove the handed
clip. Repeat for the opposite
side.
26. Using a small at screw
driver into the gap to remove
oval shaped retainer clip.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
10
29. Lift up on the bottom
and top at the same time, to
completely take off the back
part.
28. The back is hooked over
the top of the loop.
31. Jerk it up rmly until it
comes off the stem.
30. To disengage the lumbar
bow assembly from stem,
slide it all the way to the
bottom.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
11
33. Remove the lumbar stem
assembly.
32. Using T27 torx bit remove
the 2 bolts from the back
yoke.
34. Using T25 torx screw
driver remove the screws. 35. Fixed lumbar removed.
For Fixed Lumbar

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
12
37. Spine removed from the
tilt assembly.
36. Tilt forward to remove
the spine.
39. Remove the top rear tilt
cover from tilt assembly.
38. Using ngers lift the top
rear tilt cover.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
13
41. Remove the top front tilt
cover from tilt assembly.
40. Using ngers pull off the
top front tilt cover.
43. Bottom tilt cover removed
from the tilt assembly.
42. Using screw driver remove
the bottom tilt cover.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
14
44. Using Phillips screw
driver remove the two
screws from the control
retainer.
45. The control retainer is
removed from the tilt
assembly.
46. Tilt limit control removed
from the assembly. 47. Tilt tension control knob
removed from the assembly.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
15
48. Tilt controls are removed
from the tilt assembly. 49. Hold base on one hand
and grasp the caster on the
other hand.
50. Pull straight out to remove
the caster. Repeat the same
to remove other 4 casters
from base.
51. Hold base legs rmly
and strike the bottom of
cylinder with a rubber mallet
until base comes loose.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
16
52. Remove cylinder from
the base.
54. Pull out cylinder from tilt
assembly.
53. Hit the bottom of the chair
with rubber mallet until cylinder
separates from chair.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Mirra 2 are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1bc198 rev A.
17
Work Stool Footring Disassembly
1. Place nylon cap over the
end of cylinder and strike
with hammer.
2. Disengage the base from
cylinder.
3. Take out the footring from
cylinder.
YMirra 2®Disassembly for Recycling
Work Stool Footring Disassembly