HiB Vogue User manual

Quality Bathroom Products
Aluminium Cabinets - Fixing Instructions
Thank you for purchasing this HiB product. Please
read through these instructions carefully and refer
back to them during installation to ensure that your
product is fitted safely and that it retains its high
quality finish.
Please retain this leaflet for future reference.
Electrical Safety Information
HiB recommends that all electrical bathroom
products should only be fitted by a suitably qualified,
Part P registered electrician in accordance with
current IEE reguations.
Ensure mains power supply is switched off before
starting installation.
Before drilling, ensure there are no hidden cables or
pipes in the wall.
V2.1 Oct 13
Cosmic Art no. 43400 Orbital Art no. 43300
©HiB Copyright: No part of this document may be reprinted or
duplicated without HiB consent. All sizes and measurements are
approximate, but we do try and make sure they are as accurate as
possible. In the interest of continuous product development, HiB
reserves the right to alter specifications as necessary. E & OE.
zone
1
zone
2
zone
2
zone
2
zone
2
zone
2
outside
zone
60cm
60cm
60cm
60cm
75cm
75cm
75cm
75cm
60cm
radius
225cm
225cm
zone
1
zone
2
live
earth
neutral
MAINS SUPPLYLUMINAIRE
Wiring Diagram
Live supply can be Red or Brown
Earth supply is Green and Yellow
Neutral supply can be Blue or Black
Live supply is Brown
Earth supply is Green and Yellow
Neutral supply is Blue
Figure 1
Figure 2
HiB Ltd, Castle House,
21-23 Station Road,
New Barnet, Herts,
EN5 1PH
t. 020 8441 0352
f. 020 8441 0219
e. [email protected]
w. www.hib.co.uk
Care Instructions
To preserve the high quality finish of your HiB product, please ensure you regard the
following care and cleaning recommendations:
-
-
-
-
wipe off all water spillages as soon as possible
mirrors and glass can be cleaned with a proprietary cleaner using a soft cloth, taking care not to get
excessive cleaner behind the mirror
all other surfaces should be cleaned with diluted detergent, i.e. washing up liquid, and a soft cloth
scourers and scouring agents should not be used, as these may cause damage to the surface of the
product
All installations must comply
with guidelines which are
based on a zonal concept.
The diagram to the left
illustrates this concept
and must be followed to
ensure the safe installation
of bathroom lighting. These
regulations apply to domestic
installations only. Installations
must be made in accordance
with the current IEE wiring
regulations and relevant
building regulations. HiB
recommends that all electrical
bathroom products should
only be fitted by a suitably
qualified, Part P registered
electrician. This product is
IP44 rated and suitable for
installation in Zone 2 and
Outside Zones.
Vogue Art no. 42900

1) Attach the LED light fitting on the top of
the cabinet using the pre-drilled holes and
the screws provided. Push the male and
female electrical connections together until
they ‘click’.
2) Position the cabinet in a suitable location,
(according to Figure 1 on the back page),
ensuring that the domestic electrical mains
supply is within reach of the electrical
connection point of the cabinet. Carefully
mark the position of the top of the cabinet
using a soft pencil.
3) Remove the cabinet from the wall and
using a spirit level, mark a horizontal line
50mm below the original pencil mark. Hold
the mounting bracket in place with the holes
corresponding with the marked line. Ensure
the bracket is central, and mark the position
of the holes.
4) Before drilling, ensure there are no
hidden cables or pipes behind the mounting
points. Drill the required holes in the marked
positions. If drilling through tile, use a
ceramic drill bit. Insert the wall plugs level
with the surface of the wall. If fitting to a tiled
surface, wall plugs should be inserted below
the tile surface to avoid cracking. NB. For
plasterboard walls, specialist fixings should
be purchased, available from any DIY or
hardware store. Fix the bracket to the wall
using the screws provided.
5) This cabinet is provided with an electrical
supply cable already fitted. This cable
should be connected to the household
electrical circuit, and connections should
be made in accordance with the latest IEE
regulations. This is a Class I product and
must be connected to Earth. Ensure the
domestic electrical mains supply to
which the product is being connected is
turned off. Connect the domestic mains
supply according to Figure 2 on the back
page.
6) Hang the cabinet on the wall ensuring that
it is firmly located on the mounting bracket.
Align doors according to the diagram above.
7) Starting with the top shelf, insert the shelf
supports in the desired position and fit the
shelf.
attaching light fitting - orbital only
fixing preparation wall mounting door adjustment shelf assembly