HiB NOVUM N18BS60MWH User manual

Fitting Instructions
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to
them during installation to ensure that your product is fitted safely
and that it retains its high quality finish.
BLEND BASIN SHELF
60cm Matt White: Art No N18BS60MWH / 60cm Greystone: Art No N18BS60GST
60cm Sherwood Oak: Art No N18BS60SWO / 80cm Matt White: Art No N18BS80MWH
80cm Greystone: Art No N18BS80GST / 80cm Sherwood Oak: Art No N18BS80SWO
120cm Matt White: Art No N18BS120MWH / 120cm Greystone: Art No N18BS120GST
120cm Sherwood Oak: Art No N18BS120SWO
Blend 60cm Basin Shelf
Blend 80cm Basin Shelf
Blend 120cm Basin Shelf
FI#03 014 R201026 Ver 1.0 Jan 2021

2
• Please read the instructions and warnings carefully before installing the
product and ensure this document is kept with the product for future
reference to ensure product longevity and in the interest of safety.
• This product is intended for domestic use only.
• Not for use in saunas, steam rooms.
• It is recommended that this product is installed by 2 people who are able
to meet the level of competence required in order to comply with relevant
regulations.
• This product is designed for installation into a brick or masonry block wall. If
mounting onto other substrate, ensure appropriate fixing and batons are used
(if required) and the load bearing of the wall is sufficient.
• When drilling use appropriate eye protection.
• Take care when using power tools near water - the use of a residual current
device (RCD) is advised.
• Beware of hidden cables or pipes. Take care if drilling on tiled surfaces in case
the drill slips.
• Do not overload shelves or unit.
• Do not sit or stand on the unit.
• Ensure that excessive standing and surface water is removed from the product
to avoid long term damage and spoiling.
Warnings for Safe Use

3
hib.co.uk
What’s in the Box?
Tools Required
• Fitting pack
• Sealant Bottle
• Wall Brackets
• Basin Shelf
Pencil
Drill Drillbit
Tape
Measure
Sealant
Spirit Level
Masking
Tape
Silicone
Hole Saw
Screwdriver

4
Figures
900mm
4
2
3
1
1
2
3
Fig. 1 - Recommended Install Heights Fig. 2
Fig. 3
Fig. 4
Fig. 5

5
hib.co.uk
Installation
Please ensure the wall is suitable for wall hung furniture. For stud wall
installations, add an extra timber support into the stud wall prior to finishing
the wall to improve strength.
1. Establish height and location of installation. HiB recommends an installation
height of 900mm to the top of the basin, as per Fig. 1.
2. Plan wall bracket location – if a stud wall, try and place brackets on stud centres
if no other reinforcements have been made. HiB recommends that you use a spirit
level to ensure that the brackets are straight and are level. See Fig. 2.
3. Secure brackets to the wall using fixings suitable for the wall structure.
4. Position shelf onto wall brackets and check the level again. Fine adjustments
can be made by altering the adjuster bolts (Fig. 3, #1) on the end of the bracket.
5. Apply silicone sealant to the top surface of the wall brackets, then fix the shelf in
position. Screw the bracket from underneath, into the underside of the worktop to
ensure that it is secure, as per Fig. 3, #3. Allow the silicone sealant to set.
6. Assemble basin and basin waste prior to fitting basin onto countertop.
The waste assembly must be fitted to the basin only. The countertop is not
designed to be a part of the plumbing system.
7. Mark out location of tap(s) and basin(s). Applying masking tape over the area
to be cut will aid marking out and also help prevent the laminate surface from
chipping. Cut suitable apertures for brassware and plumbing as required, using a
hole saw or jigsaw as per Fig. 4.
8. All cut edges MUST be sealed fully with the sealant provided with the product
as per Fig. 4. Failure to do this will invalidate the warranty.
9. Install tap(s) and basin(s) in desired position. It is important that tap(s) and
basin(s) is securely siliconed in place – as per Fig. 5. This helps prevent any
unwanted movement and also prevents water ingress. Allow silicone to set fully
before use.

6
Adjustment & Removal
BLANK PAGE

7
hib.co.uk
Care
Aftercare
In the unlikely event that this product should fail please contact the retailer from
which the item was purchased.
To preserve the high quality finish of your HiB product, please ensure you regard
the following care and cleaning recommendations:
• Use only a so damp cloth.
• Wipe off all water spillages as soon as possible.
• Do not use any abrasives or solvents.

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try
and make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary.
E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN