HiB AARON Owner's manual
AARON
TECHNICAL INFORMATION, MARCH 2010
Thank you for purchasing this HiB product. Please read through these instructions carefully and
refer back to them during installation to ensure that your product is fitted safely and that it retains
its high quality finish. Please retain this leaflet for future reference.
This instruction leaflet applies to the following products:
AARON ART NO: 73105900
IMPORTANT INSTALLATION INFORMATION
THIS IS A CLASS I PRODUCT AND MUST BE CONNECTED TO EARTH
INPUT: 220-240V ac 5A IP RATING: IP44
HAZARDOUS VOlTAGES INSIDE - DO NOT OPEN SEALED UNITS
All installations must comply with guidelines which are based on a zonal concept. The colour
coded diagram below illustrates this concept and must be followed to ensure the safe installation
of bathroom lighting. These regulations apply to domestic installations only. Installations must be
made in accordance with the current lEE wiring regulations and relevant building regulations. HiB
recommends that all electrical bathroom products should only be fitted by a suitably qualified,
Part P registered electrician.
BOcm
seem
60cm
60cm
.....
E
E
o
E
~
'"
;?
,..
i
c
,-,
li
:
2'(
Ii·'
li1
l21
6Ocm.,~
E
121
.jl
...
'"
cv
ZONE
1
lONE
2
OUTSIDE
ZONES
Refers 10the area above the bath
or shower up to a height of 2.25
metres and requires a minimum
rating of
IPX4 (splash-proof
Covers an area 0.6 metres
vtide
immediately next to, and all round
zone 1.Wash basins should
also be treated as zone 2. The
minimum rating here is IPX4.
Has no special requirements,
unless water jets are likely 10 be
used for deaning purposes.
FIXING INSTRUCTIONS
1. Position the mirror in a suitable location, ensuring that the domestic electrical mains supply is
within reach of the electrical entry point of the product.
2. Carefully mark the position of the product using a soft pencil.
3. Remove the mirror, and mark the positions of the two mounting points.
mounting point back view
mounting point
\ mounting screw
J
I
AARON
4. Using a 6mm masonry drill, drill the holes in the marked positions to a depth of 50mm. If
drilling through tiles, use a ceramic drill bit.
5. Insert the wall-plugs level with the surface of the wall. If fitting to a tiled surface, wall plugs
should be inserted below the surface of the tile to avoid cracking.
6. Insert fixing screws into the wall plugs.
7. Ensure the domestic electrical mains supply to which the product is being connected is
turned off. Connect the domestic mains supply to the terminal box inside the frame,
according to the wiring diagram below.
Brown
Green and Yellow
Blue
&
live
&
II
s
e rth
s
&
neutr l
s
LUMINAIRE MAINS SUPPLY
WIRING DIAGRAM
Brown
Red
Green and Yellow
BlueJ Black
BULB REPLACEMENT
This product requires: LEDs not replaceable
OPERATING INSTRUCTIONS
LED
Illumination
To turn illumination on or off, operate the sensor switch located bottom centre.
PRODUCT CARE
To preserve the high quality finish of your HiB product, please ensure you regard the following
care and cleaning recommendations:
wipe off all water spillages as soon as possible
mirrors and glass can be cleaned with a proprietary cleaner using a soft cloth, taking care
not to get excessive cleaner behind the mirror
all other surfaces should be cleaned with diluted detergent, i.e. washing up liquid, and a
soft cloth
scourers and scouring agents should not be used, as these may cause damage to the
surface of the product
PRODUCT ST ND RDS
This product is in compliance with the following directives:
BSEN 60598-1:2004+A1 2006
BSEN 60598-2-11989
LOW VOLTAGE DIRECTIVE 2006/95/EC
EMC DIRECTIVE 89/336/EEC
RoHS DIRECTIVE 2002/95/EC
REACH DIRECTIVE 1907/2006/EC
WEEE DIRECTIVE 2002/96/EU
HiB Ltd
Castle House,
21/23
Station Road
New Barnet, Herts. EN5 1PH
Tel: 0208441 0352Fax: 02084410219
Other HiB Personal Care Product manuals
