HiB Spectre 50 User manual

T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the
interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
This product is suitable for installation in zones:
FI#01 018 R211007 Ver No. 1.0 Jan 2017
2 &Outside Zone
All installations must comply with guidelines which are based on a zonal
concept. The diagram above illustrates this concept and must be followed
to ensure the safe installation of electrical appliances in the bathroom.
These regulations apply to domestic installations only. Installations must be
made in accordance with the current IEE wiring regulations and relevant
building regulations. HiB recommends that all electrical bathroom
products should only be fitted by a suitably qualified, Part P registered
electrician.
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to them
during installation to ensure that your product is fitted safely and that it
retains its high quality finish.
Please retain this leaflet for future reference.
Before installation, ensure the domestic electrical mains supply to
which the mirror is to be connected is turned off. Before drilling,
ensure that there are no hidden cables or pipes in the wall.
(Fig. 1)
Mounting Points Diagram (Fig. A)
Illuminated Mirrors
Spectre 50 Art No. 79510000 Spectre 60 Art No. 79520000
Spectre 100 Art No. 79530000
Operation Instructions
To turn illumination on touch the sensor once.
To change the colour temperature, touch and hold the sensor until
desired colour is obtained. The colour temp is then set until changed
again.
Heated Pad is only on when mirror is illuminated.
Care Instructions
Do not use abrasives or solvents when cleaning this product.
Wipe off all water spillages as soon as possible using a so, damp cloth.
Aercare Service
In the unlikely event that this product should fail please contact HiB
customer services, details shown below.
Installation
Ensure the domestic electrical mains supply to which the mirror
is being connected is turned off.
1. Position the mirror in a suitable location (according to the zonal
diagram - Fig. 1), ensuring that the domestic electrical mains
supply is within reach of the cable connection point of the
product.
2. Carefully mark the position of the mirror using a so pencil
ensuring it is level. Remove the mirror and mark the mounting
points (see Fig. A) Please ensure that all marked mounting
points accurately match up with the fixing points on the
mirror.
3. Using a suitable drill bit, drill holes in the marked positions to a
suitable depth. If drilling through tile, use a ceramic drill bit.
4. Insert wall plugs level with the surface of the wall. If fitting to a
tiled surface, wall plugs should be inserted below the tile surface
to avoid cracking. NB. For plasterboard walls, specialist fixings
should be purchased, available from any DIY or hardware store.
5. Screw supplied fixings into wall plugs.
6. Connect the domestic mains supply to the terminal box according
to the wiring diagram opposite (Fig. B).
7. Hang the mirror in position.
8. Switch the domestic electrical mains supply for the mirror back
on.
mounting points
REAR VIEW
Hanging Portrait
Hanging landscape
ONLY Spectre 60 can be hung either
portrait or landscape
WEEE compliance
Must not be mixed with general household waste
This product contains a light source of energy efficiency class E

T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the
interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
live
earth
neutral
MAINS SUPPLYLUMINAIRE
Wiring Diagram
Live supply can be Red or Brown
Earth supply is Green and Yellow
Neutral supply can be Blue or Black
Live is Brown
Neutral is Blue
Caution
We recommend that you place this mirror on a so flat surface to ensure no
breakages. We also recommend that you leave corner protectors on until final fitting
Wiring Diagram (Fig. B)
This is a double insulated product and does not require an earth