HiB Hannah 73106200 User manual

T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the
interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
This product is suitable for installation in zones:
FI#01 008 R151124 Ver No. 1.0 Jan 2016
2 &Outside Zone
All installations must comply with guidelines which are based on a zonal
concept. The diagram above illustrates this concept and must be followed
to ensure the safe installation of electrical appliances in the bathroom.
These regulations apply to domestic installations only. Installations must be
made in accordance with the current IEE wiring regulations and relevant
building regulations. HiB recommends that all electrical bathroom
products should only be fitted by a suitably qualified, Part P registered
electrician.
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to
them during installation to ensure that your product is fitted safely
and that it retains its high quality finish.
Please retain this leaflet for future reference.
Before installation, ensure the domestic electrical mains supply
to which the mirror is to be connected is turned off. Before
drilling, ensure that there are no hidden cables or pipes in the
wall.
(Fig. 1)
Mounting Points Diagram (Fig. A)
Installation
NB. This product must be installed with a minimum of 150mm between the
sensor and any adjacent wall or object to ensure correct operation of the
switch.
1. Position the mirror in a suitable location (according to the zonal
diagram, Fig 1), ensuring that the domestic electrical mains
supply is within reach of the electrical entry point of the product.
2. Carefully mark the position of the mirror using a so pencil.
3. Remove the mirror and mark the mounting points according
to the diagram on the le. Please ensure that all marked
mounting points accurately match up with the fixing points
on the mirror. Please note that only the Hannah mirror is
mountable in landscape and portrait configurations.
4. Before drilling, ensure there are no hidden cables or pipes
behind the mounting points. Using a masonry drill, drill holes in
the marked positions to a suitable depth. If drilling through tile,
use a ceramic drill bit.
5. Insert wall plugs level with the surface of the wall. If fitting to a
tiled surface, wall plugs should be inserted below the tile surface
to avoid cracking. NB. For plasterboard walls, specialist fixings
should be purchased, available from any DIY or hardware store.
Screw hook screws into wall plugs.
6. Rain, Celeste, Keo & Aztec only: Attach shelf to mirror using
the fixings provided. Care must be taken not to overtighten
screws to prevent damage.
7. Ensure the domestic electrical mains supply to which the mirror
is being connected is turned off. Connect the domestic mains
supply to the terminal box as per the wiring diagram (Fig A).
8. Hang the mirror in position.
mounting points
electrical input
REAR VIEW
to mains
Illuminated Mirrors
Rain Art No. 73105200
Celeste Art No. 73105400
Keo Art No. 73106000
Aztec Art No. 73105300
Hannah Art No. 73106200
Lunar Art No. 73104395
Duna Art No. 73104195
Solar Art No. 73104095
Aaron Art No. 73105900
mounting points
electrical input
alternate mouting points
REAR VIEW
to mains
Portrait & Landscape options
available on Hannah mirror only

T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the
interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
WEEE compliance
Must not be mixed with general household waste
Operating Instructions
To turn illumination on or off, operate the sensor switch located at the
bottom of the mirror.
Heated Pad is only on when mirror is illuminated.
Rain, Celeste, Keo & Aztec only: charging socket is suitable for
recharging toothbrushes. NB. On first use of the charging socket,
inserting the plug may prove to be stiff. Reasonable force may be
required to fully insert the plug. Make sure that the mirror is held firmly
so that it is not pushed off the wall. Aer a few uses, stiffness will ease
and the socket will function as normal.
Care Instructions
Do not use abrasives or solvents when cleaning this product.
Wipe off all water spillages as soon as possible using a so, damp
cloth.
Aercare Service
In the unlikely event that this product should fail please contact HiB
customer services, details shown below.
LEDs cannot be replaced.
live
earth
neutral
MAINS SUPPLYLUMINAIRE
Wiring Diagram
Live supply can be Red or Brown
Earth supply is Green and Yellow
Neutral supply can be Blue or Black
Live is Brown
Earth is Green and Yellow
Neutral is Blue
Wiring Diagram (Fig. B)