Hodedah 98802 User manual

ASSEMBLY INSTRUCTIONS
PAGE 1 OF 5
NOTE : MUST TIGHTEN SCREWS PERIODCALLY.SCREW NATURALLY LOOSEN WITH USE.CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
No ITEM Qty
A
Headboard
1 pc
B
Headboard Left & Right
2 pcs
B.1
Headboard Leg Support
1583 x 45 x 18 1 pc
No ITEM Qty
1JCBC M6 x 35mm 8 pcs
2SPRING WASHER 1/4" Rbw 8 pcs
3Flat Washer 1/4"ID x 19mmOD
Blk 8 pcs
4ALLEN KEY m4x65mm Blk 1 pc
4.1 Flat Head Chipboard Screw
m4x32mm Rbw 2 pcs
NAIL LEG
No ITEM Qty
J
Trundle Drawer Bottom Panel
2 pcs
K
Trundle Drawer Bottom Support
with custor wheel 4 pcs
L
Trundle Drawer Bottom Support
without custer wheel 4 pcs
No ITEM Qty
5
K1536 D34mmxH22mm
Handle Antique Brass 4 pcs
6
Handle Screw m4x35mm Blk
4 pcs
7
Flat Head Chipboard Screw
m4x32mm Rbw 24
pcs
8
Pan Head Chipboard Screw
m3.5x16mm Blk 12
pcs
9
Wood Dowel 6mmx30mm 16
pcs
No ITEM Qty
10 Flat Head Chipboard Screw
m4x32mm Rbw 18
pcs
11 JCBC M6 x 50mm 2 pcs
12 ALLEN KEY m4x65mm Blk 1 pc
13 ALLEN KEY m5x65mm Blk 1 pc
No ITEM Qty
M
Side Rail
2 pcs
No ITEM Qty
C
Footboard 1 pc
D
Slat
1545 x 45 x 18 9 pcs
E
Center Slat -
L1500 x 45 x 18 1 pc
F
Slat Support -
L320 x 30 x 30 2 pcs
G
Trundle Drawer Front Panel 2 pcs
H
Trundle Drawer Side Panel
4 pcs
I
Trundle Drawer Back Panel
2 pcs

ASSEMBLY INSTRUCTIONS
PAGE 2 OF 5
NOTE : MUST TIGHTEN SCREWS PERIODCALLY.SCREW NATURALLY LOOSEN WITH USE.CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
RIGHT
LEFT
2
1
4
3
x8
B
M
13
13
M
B
_
STEP 1 : Attached and tighten the Headboard Leg L/R ( B )
to the Headboard ( A ).Insert Spring Washer ( 2 )
Flat Washer ( 3 ),use JCBC Bolt ( 1 ) to fix with
Allen Key ( 4 ). Fix the Headboard support Leg (B.1)
and tighten with screw (4.1) accordingly as shown.
Loosen the JCBB Bolt from Headboard Leg (B) and Footboard (C) using
ALLEN KEY (13).Attach the Side Rail (M) to Headboard Leg (B) and
Footboard (C) by pushing the bracket down to fit it.Tighten the JCBB Bolt with
ALLEN KEY (13).
STEP 2 :
B
A
BACK VIEW
C
M
A
B
A
B
4.1
B.1
LEFT
RIGHT

ASSEMBLY INSTRUCTIONS
PAGE 3 OF 5
NOTE : MUST TIGHTEN SCREWS PERIODCALLY.SCREW NATURALLY LOOSEN WITH USE.CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
STEP 3 : Fix the Bed Slat Support ( F ) with adjuster,Center Rail ( E ) to Bed
Slat ( D ). Attach the Assembled Bed Slat to Side Rail ( M ) Loosen and
Tighten Adjuster for the Stability of Bed. Laterly, Tighten the Bed Slat
( F ) with JCBC Screw ( 11 ).
STEP 4 : Install the Handle in front of footboard drawer.Tighten the Handle
Screw using Screw Driver.( Not Included )
10
D
F
E
11 12
Push the rail meet
with wooden slat
and fix the CSK
screw ( 10 ) by
using the Screw
Driver
x18
D

ASSEMBLY INSTRUCTIONS
PAGE 4 OF 5
NOTE : MUST TIGHTEN SCREWS PERIODCALLY.SCREW NATURALLY LOOSEN WITH USE.CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
STEP 5(a) : Place the trundle drawer front panel
( G ) on clean surface then Fix the trundle drawer
box side panel (H) by inserting a dowel ( 9 ) then
tighten with csk screw ( 7 ) using Screw Driver as
per diagaram shown.(DO NOT FULLY TIGHTEN
IN THIS STEP)
STEP 5 (b) : Slide in the bottom drawer panel (J)
inside the groove of trundle drawer box side panel
( H ) and push it down to trundle front panel ( G )
as per diagram shown.
BOTTOM SURFACE
STEP 5 (c) : Fix the trundle drawer back panel ( I ) and trundle
drawer box side panel ( H ) by inserting a dowel ( 9 ) then tighten
with csk screw ( 7 ) using Screw Driver as per diagram shown.
(FULLY TIGHTEN ALL SCREWS IN THIS STEP)
8
J
BOTTOM SURFACE
STEP 5 (d) : Fix the trundle bottom
drawer panel ( J ) with Pan head
Screw ( 8 ) and tighten using Screw
Driver as per diagram shown.
x2
x4 x6
x4
9
7
I
H
I
J
H
H
LINE MARKING
G
H
H
79
G
G
7
K
STEP 5 (e) : Fix the trudle bottom support rail
( K ) & ( L ) and tighten using Screw Driver as
per diagram shown.
x8
BOTTOM SURFACE
x2 K
L
FOLLOW THE MARKING
LINE
FOLLOW THE MARKING
LINE
H

ASSEMBLY INSTRUCTIONS
PAGE 5 OF 5
NOTE : MUST TIGHTEN SCREWS PERIODCALLY.SCREW NATURALLY LOOSEN WITH USE.CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
STEP 6 : Install the Handle drawer ( 5 ) in front of Trundle drawer (G).Tighten
the Handle Screw (6 ) using Screw Driver.( Not Included )
5
6
G
G
COMPLETE
ASSEMBLE
STEP 7 : Push The complete assembled Trundle drawer into side rail ( M ) as per
diagram shown.
M
M
x2

Cut of the Raffia String from the back of DRESSER ( B ).
STEP 1 : Place the MIRROR FRAME (A) on the top of DRESSER (B), turn the
MIRROR SUPPORT RAIL (C) upward at the back of DRESSER (B), then
Tighten with FLAT HEAD CHIPBOARD SCREW (1).
STEP 2 :
STEP 3 :
NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
ASSEMBLY INSTRUCTIONS
Tighten the FLAT HEAD CHIPBOARD Screw (1) as shown.
1
C
B
MAKE SURE ARROW
FACE TO FACE
B
A
C1
X6
X4
Arrow Must
Face to face
C
STYLE # : 98804 & 98805
NOMA DRESSER &
MIRROR
(BOX 1)
NO ITEM QTY
A
MIRROR
1 PC
BOX OF MIRROR
(BOX 1)
(BOX 2)
NO ITEM QTY
B
DRESSER
1 PC
C
MIRROR SUPPORT
2 PCS
BOX OF DRESSER
(BOX
NO ITEM QTY
1
FLAT HEAD CHIPBOARD
SCREW m4 x 32mm RBW
10 PCS
(BOX 1)
BOX OF MIRROR
(BOX