Hoist Fitness CFG-3753 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
CFG-3753
7 DEGREE SMITH
A00
OWNER'S MANUAL
Note: Both Serial Number and Model Number are Required when Ordering Parts
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.

02
04
23
27
28
29
32
33
39
41
42
43
44
45
46
OWNER'S MANUAL
PAGE 01 CFG-3753 ASSEMBLY
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
WEIGHT RATIOS....................................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
CONTENTS

OWNER'S MANUAL
PAGE 02
CFG-3753 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
2 People Required For Assembly
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
OWNER'S MANUAL
PAGE 03 CFG-3753 ASSEMBLY

OWNER'S MANUAL
PAGE 04
CFG-3753 ASSEMBLY
FRAME ASSEMBLY

PAGE 05
OWNER'S MANUAL
CFG-3753 ASSEMBLY
- WRENCH TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
NOTE:
FRAME ASSEMBLY
29
10
47
66
64
MAKE SURE DECALS FACE
OUTWARD, AS SHOWN

MAKE SURE SIDE WITH BOLT
HEAD FACES OUT, AS SHOWN
OWNER'S MANUAL
CFG-3753 ASSEMBLY PAGE 06
WARNING!
BE SURE TO ALWAYS SUPPORT UPRIGHT (1) THROUGH THE FOLLOWING STEPS
UNTIL ASSEMBLY IS SECURED ON PAGE 10.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE
UPRIGHT.
- SOME PARTS HAVE BEEN
REMOVED FOR CLARITY.
18
60
62
29
1
62
70
LEFT SIDE SHOWN

14
98 1/8" 2492
14
LEFT SIDE SHOWN
56
63
24
24
63
69
69
63
63
54
55
63
20 69
63
20
CABLE MAY COME
PRE-ASSEMBLED
OWNER'S MANUAL
PAGE 07 CFG-3753 ASSEMBLY
WARNING!
BE SURE TO ALWAYS SUPPORT UPRIGHT (1) THROUGH THE FOLLOWING STEPS
UNTIL ASSEMBLY IS SECURED.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE
UPRIGHT.
FRAME ASSEMBLY

59
62
2
2
70
62
12
17
OWNER'S MANUAL
CFG-3753 ASSEMBLY PAGE 08
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- HAND TIGHTEN HARDWARE.
FRAME ASSEMBLY
NOTE:
WARNING!
BE SURE TO ALWAYS SUPPORT UPRIGHTS (2) THROUGH THE FOLLOWING STEPS
UNTIL ASSEMBLY IS SECURED.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.

14
20
UPRIGHT (1), AS SHOWN
BE SURE TO POSITION
CABLE (14) AROUND PULLEY
AND THROUGH SLOT IN
1
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE
UPRIGHT.
FRAME ASSEMBLY
CFG-3753 ASSEMBLY
OWNER'S MANUAL
PAGE 09
WARNING!
BE SURE TO ALWAYS SUPPORT UPRIGHT (1) THROUGH THE FOLLOWING STEP,
WHEN UNIT WILL BE SECURED.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.
34
1
2
LEFT SIDE SHOWN
62
59
14 70
2
62
CUT-OFF THE ZIP TIE
TO POSITION CABLE
AS SHOWN