Hoist Fitness MC-7030 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
Note: Both Serial Number and Model Number are Required when Ordering Parts
OWNER'S MANUAL
A00
MC-7030
SHELF OPTION

02
04
07
08
09
10
11
PAGE 01
OWNER'S MANUAL
ABBREVIATIONS...................................................................
MC-7030 ASSEMBLY
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
CONTENTS

OWNER'S MANUAL
PAGE 02MC-7030 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

OWNER'S MANUAL
PAGE 03 MC-7030 ASSEMBLY
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

*
**
**
**
**
*AS THE MC-7018 OR MC-7019
*
MC-7017
MC-7032
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
OTHER STATIONS MAY BE USED
INSTEAD OF THE MC-7017, SUCH
*
*
STEP 1: INSTALL THE MC-7032
NOTE:
- HAND TIGHTEN HARDWARE.
PARTS INCLUDED WITH THE MC-7017
PARTS INCLUDED WITH THE MC-7032
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY
OWNER'S MANUAL
MC-7030 ASSEMBLY PAGE 04

*
*
**
*
*
*
*
*
*
*
MC-7012
*
*
*
*
*
*
*
*
*
MC-7032
NOTE:
- HAND TIGHTEN HARDWARE.
PARTS INCLUDED WITH THE MC-7012
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 05 MC-7030 ASSEMBLY

2
3
4
5
1
MC-7032
STEP 2: INSTALL THE MC-7030
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
OWNER'S MANUAL
MC-7030 ASSEMBLY PAGE 06

DECAL PLACEMENT
NOTE:
- ALL DECALS ARE CENTERED
UNLESS OTHERWISE STATED.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
OWNER'S MANUAL
PAGE 07 MC-7030 ASSEMBLY
8

SERIAL # DECAL
DECAL REFERENCE
OWNER'S MANUAL
MC-7030 ASSEMBLY PAGE 08

PART LIST
OWNER'S MANUAL
PAGE 09 MC-7030 ASSEMBLY
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 026-01P5709 SHELF 1
2 026-01PL2606 .472" X 4.6250" X 27.1250" FLOORING 1
3 013-1002006 1/2" X 27mm SAE FLAT WASHER (Ni) 2
4 011-0702029 1/2"-13UNC X 2.25" FHS (Ni) 2
5 012-0504002 1/2"-13 UNC THIN NYLOCK NUT (Ni) 2
6 011-0702042 1/2"-13UNC X 5.50" FHS (Ni) 2
7 013-1009002 1/2" CURVED WASHER (Ni) 2
8 SERIAL # DECAL DECAL HOIST SERIAL # 1.63" X 2.63" 1