Hoist Fitness ROC-IT RPL-5102-A User manual

Fax
FaxFax
Fax
[phone]
[phone](858) 578-7676
[phone]
[phone]
[phone](858) 578-9558
[phone]
Customer Service
Customer ServiceCustomer Service
Customer Service
[phone]
[phone](800) 548-5438
[phone]
RECORD SER AL NUMBER HERE
RECORD SER AL NUMBER HERERECORD SER AL NUMBER HERE
RECORD SER AL NUMBER HERE
MACH NE CODE
MACH NE CODEMACH NE CODE
MACH NE CODE
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR USING MINIMUM 4-1/2" LONG BOLTS. FAILURE
TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH.
Note: Both Serial Number and Model Number are Required when Ordering Parts
Note: Both Serial Number and Model Number are Required when Ordering PartsNote: Both Serial Number and Model Number are Required when Ordering Parts
Note: Both Serial Number and Model Number are Required when Ordering Parts
OWNER'S MANUAL
OWNER'S MANUAL OWNER'S MANUAL
OWNER'S MANUAL
A08
A08A08
A08
RPL-5102-A
PLATE LOADED PREACHER CURL

02
04
31
32
33
34
37
40
41
42
44
45
46
47
48
EXERCISE LOG......................................................................
OWNER'S MANUAL
PAGE 01 RPL-5102-A ASSEMBLY
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
MACHINE ADJUSTMENT .....................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
CONTENTS

OWNER' S MANUAL
PAGE 02
RPL-5102-A ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
OWNER' S MANUAL
PAGE 03 RPL-5102-A ASSEMBLY

OWNER'S MANUAL
PAGE 04
RPL-5102-A ASSEMBLY
FRAME ASSEMBLY

NOTE:
BE SURE THE CABLE (1) RUNS
BETWEEN THE PULLEYS (32, 33)
AND THE GUARD RODS AS SHOWN.
REMOVED FOR CLARITY.
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
CABLING PROFILE VIEW
PAGE 05
OWNER'S MANUAL
RPL-5102-A ASSEMBLY
32
1
33
32
1
BOTTOM SECTION VIEW
33 33
32 32
32
24
1
33
GUARD RODS

NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
FRAME ASSEMBLY
OWNER'S MANUAL
RPL-5102-A ASSEMBLY PAGE 06
59
85
86 60
6
59
74
32
24
GUARD PINS
1
NOTE:
BE SURE TO POSITION THE
CABLE (1) BETWEEN THE
GUARD PINS AS SHOWN.
1
132 9/32" 3360

- WRENCH TIGHTEN HARDWARE.
NOTE:
SAME TIME.
- INSTALL CABLE AND PULLEYS AT THE
FRAME ASSEMBLY
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
PAGE 07
OWNER'S MANUAL
RPL-5102-A ASSEMBLY
1
74
59
59
85
PULLEY (32) AS SHOWN.
32
32
BE SURE TO POSITION
CABLE (1) BETWEEN
24

1
59
75
24
33
59
85
33
SAME TIME.
- INSTALL CABLE AND PULLEYS AT THE
FRAME ASSEMBLY
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- WRENCH TIGHTEN HARDWARE.
NOTE:
OWNER'S MANUAL
RPL-5102-A ASSEMBLY PAGE 08
1
33
GUARD RODS
BE SURE TO POSITION CABLE
(1) BETWEEN THE PULLEY (33)
AND THE GUARD RODS AS SHOWN.

NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY
PAGE 09
OWNER'S MANUAL
RPL-5102-A ASSEMBLY
51
24
16
23