Hoist Fitness CF Commercial Freeweight CF-3461-2 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
CATALOG NUMBER LOT CODE
OWNER'S MANUAL
Note: Both Serial Number and Model Number are Required when Ordering Parts
0507 - 003 D
CF-3461-2
2 TIER DUMBBELL RACK
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.

02
04
07
08
09
10
11
13
15
16
17
19
20
OWNER'S MANUAL
PAGE 01 CF-3461-2 ASSEMBLY
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
CONTENTS

OWNER'S MANUAL
PAGE 02
CF-3461-2 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
OWNER'S MANUAL
PAGE 03 CF-3461-2 ASSEMBLY

OWNER'S MANUAL
PAGE 04
CF-3461-2 ASSEMBLY
FRAME ASSEMBLY

NOTE:
- WRENCH TIGHTEN HARDWARE.
FRAME ASSEMBLY
PAGE 05
OWNER'S MANUAL
CF-3461-2 ASSEMBLY
15
13
10
13
6
13
10
3
1
15
13
2

FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
OWNER'S MANUAL
CF-3461-2 ASSEMBLY PAGE 06
12
4
1
5
14
8
9
23
12
7

DECAL PLACEMENT
PAGE 07
OWNER'S MANUAL
CF-3461-2 ASSEMBLY
20
21
20
18
21
19
17
20
21
18
22
19
21
16
20

021-0003221
021-0003627
021-0003135
021-0003008
021-0003347021-0003341SERIAL # DECAL
DECAL REFRENCE
OWNER'S MANUAL
CF-3461-2 ASSEMBLY PAGE 08

PART LIST
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
PAGE 09
OWNER'S MANUAL
CF-3461-2 ASSEMBLY
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 026-01X5223 SIDE FRAME ASSEMBLY 2
2 026-01X3208 LOWER TIER ASSEMBLY 1
3 026-01X3209 UPPER TIER ASSEMBLY 1
4 026-01PL2449 DUMBBELL SADDLE (THRU HOLE) 40
5 026-01M2276 END CAP DOMED 2
6 026-01P3552 SIDE PLATE 2
7 026-01PL2211-B RUBBER FOOT 4
8 011-0101034 3/8"-16UNC X 1.25" BHCS (WZ) 2
9 011-0101026 3/8"-16UNC X 1.00" BHCS (WZ) 40
10 011-0102030 1/2"-13UNC X 5.25" HHB (WZ) 8
12 013-0402007 3/8" X 22mm FLAT WASHER (WZ) 80
13 013-0102003 1/2" X 27mm SAE FLAT WASHER (WZ) 16
14 013-0102020 3/8" SPLIT LOCK WASHER (WZ) 2
15 012-0304011 1/2"-13 UNC THIN NYLOCK NUT (WZ) 8
16 021-0003008 DECAL COMMERCIAL MAINTENANCE 1.50 X 6.69 1
17 021-0003135 DECAL WARNING 1.50" X 6.69" 1
18 021-0003221 DECAL HOIST 2.50" X 9.13" 2
19 021-0003627 DECAL HOIST 2.12" X 7.75" 2
20 021-0003347 DECAL 1,400 LB WEIGHT RATING FOR THIS TIER (1.63" X 1.63") 4
21 021-0003341 DECAL PINCH POINT 1.07" X 2.13" (HORIZONTAL) 4
22 SERIAL # DECAL DECAL SERIAL # 1.63" X 2.63" 1
23 012-0104008 3/8"-16 UNC THIN NYLOCK NUT (WZ) 40

SHCS = Socket Head Cap Screw
SHSS = Socket Head Shoulder Screw
BZ = Black Zinc
WZ = White Zinc
HHB = Hex Head Bolt
FHCS = Flat Head Cap Screw
BHCS = Button Head Cap Screw
ABBREVIATIONS
PAGE 10
OWNER'S MANUAL
CF-3461-2 ASSEMBLY

BOLT SIZING CHART
3 3/4"
OWNER'S MANUAL
PAGE 11 CF-3461-2 ASSEMBLY
5 1/4"4 1/4"
4 3/4"
5"
5 1/2"
4"
4 1/2"
4 3/4"
5"
5 1/2"
4"
4 1/2"
5 1/4"4 1/4"
5 1/4"
5"
5 1/2"
4 1/4"
4"
4 1/2"
4"
4 3/4"
3 1/4"2 1/4"
2 3/4"1 3/4"
1 1/4"
3"
3 1/2"2 1/2"
2 3/4"
3"
3 1/2"2 1/2"
3 1/4"2 1/4"
1 1/2"
1 3/4"
1"
1 1/2"
1"
1 1/4"
2"
2"
5/16" HHB
0"
0"
3/8" HHB
3 1/4"
3"
3 1/2"
2 1/4"
2 1/2"
3 1/4"2 1/4"
2 3/4"
1 1/2"
1"
1 1/4"
1 3/4"
1 1/4"
2"
3 1/2"2 1/2"
3"
1 1/2"
1" 2"
0"
1/2" HHB
0"
1/2" SHSS
2 3/4"1 3/4" 3 3/4"
3 3/4"
3 3/4"

(CONTINUED)
3"
3/8" BHCS
1/4" HHB
0" 1"
1 1/4"
3/4"
1 1/2"
0"
1"
0"
1/2" FHCS
0"
3/8" FHCS
3/8" SHCS
1 3/4" 2 3/4"3/4"
1 1/4"
3/4"
0" 1"
2 1/4"
1 1/2"
2"
2 1/2"
1"
3/4"
3/4"
BOLT SIZING CHART
PAGE 12
OWNER'S MANUAL
CF-3461-2 ASSEMBLY

013-0102003
1/2"
013-0102018
LOCK WASHER
SMALL, SAE, 13mm
FLAT WASHER
1/4"
013-0002003
LARGE, USS, 34mm
FLAT WASHER
1/2"
SPACER
3/8" FENDER WASHER
013-0003002
PLASTIC 1 1/16"
026-01PL151
FENDER WASHER
1/2" LONG
014-0018001
013-0102026
LARGE, USS, 25mm
FLAT WASHER
3/8"
013-0402005
SMALL, SAE, 21mm
FLAT WASHER
3/8"
LOCK WASHER
1" SHIM WASHER
016-0009003
3/8"
013-0102020
LOCK WASHER
1/4"
013-0102019
FLATHEAD CAP
2" ALUMINUM
026-01M0238
CURVED WASHER
3/8"
013-0102028
013-0002004
LARGE, USS, 22mm
FLAT WASHER
5/16"
013-0102004
22mm O.D.
1 1/16"
013-0003004
FENDER WASHER
FLAT WASHER
3/8"
SPACER
1" LONG
014-0018002
013-0402007
SMALL, SAE, 27mm
FLAT WASHER
1/2"
WASHER SIZING CHART
PAGE 13
OWNER'S MANUAL
CF-3461-2 ASSEMBLY

026-01M0600
.625" LONG
FLANGED SPACER
1/4" LONG
026-01M0211
FLANGED SPACER
1/2" LONG
026-01M0198
FLANGED SPACER
1/2" LONG HEAVY
026-01M0760
FLANGED SPACER
1/4" LONG HEAVY
026-01M211T
FLANGED SPACER
11/16" LONG HEAVY
026-01M0532
FLANGED SPACER
1" LONG HEAVY
026-01M0551
FLANGED SPACER
.81" LONG HEAVY
026-01M0788
FLANGED SPACER
.65" LONG HEAVY
026-01M0780
FLANGED SPACER
1 11/16" LONG HEAVY
026-01M0761
FLANGED SPACER
.44" LONG HEAVY
026-01M0789
FLANGED SPACER
1 1/2" LONG HEAVY
026-01M0762
FLANGED SPACER
1 1/4" LONG HEAVY
026-01M0768
FLATHEAD CAP
1 5/8" ALUMINUM
026-01M0239
FLATHEAD CAP
1 3/8" ALUMINUM
026-01M0240
FLANGED SPACER
WASHER SIZING CHART
(CONTINUED)
PAGE 14
OWNER'S MANUAL
CF-3461-2 ASSEMBLY

Cables, Belts and Connecting Parts
Seat Sleeves, Turcite Bushings,
For personal, in home use, please follow the home maintenance schedule listed above.
Your equipment comes with a commercial maintenance decal.
MAINTENANCE
DAILY
DAILY
WEEKLY
WEEKLY
WEEKLY
DAILY
COMMERCIAL
MAINTENANCE
WEEKLY
WEEKLY
WEEKLY
3 MONTHS
3 MONTHS
3 MONTHS
HOME
Upholstery
Clean;
Linear Bearing
Swivels, Weight Stack Pins
ROUTINE
Links, Pull Pins, Snap Locks,
All Decals
Inspect;
Accessory Bars, and Handles
Inspect;
Inspect;
tension
Cables or Belts and their
All Nuts and Bolts, Tighten if needed
Inspect;
WEEKLY
MONTHLY
MONTHLY
YEARLY
6 MONTHS
6 MONTHS
3 MONTHS
3 MONTHS
3 MONTHS
YEARLY
3 YEARS
YEARLY
MAINTENANCE SCHEDULE
Anti-Skid Surface
Inspect;
All Glossy Finishes
Clean and Wax;
Linear Bearings
Repack with Grease;
Inspect;
based lubricant (Superlube)
Guide Rods with a Teflon (PTFE)
Clean & Lubricate;
Lubricate;
Replace;
LATEST DATE ENTRY
PAGE 15
OWNER'S MANUAL
CF-3461-2 ASSEMBLY

etc.) into the inside of the bearing. Using your finger, press the grease into the ball-bearings and their tracks. repeat until the ball-bearing
tracks are full of grease. Insert the shaft back into the bearing and wipe off excess grease.
HOIST FITNESS SYSTEMS
GENERAL MAINTENANCE INFORMATION
Links, Pull-Pins, Snap Hooks, Swivels, Weight Stack Pins:
*Check all pieces for signs of visible wear or damage.
*Check springs in snap hooks and pull-pins for proper tension and alignment.
*If the spring sticks or has lost its rigidity, replace it immediately.
Upholstery:
*To ensure prolonged upholstery life and proper hygiene, all upholstered pads should be wiped down with a damp cloth after every workout.
*Periodically take the time to use a mild soap or an approved vinyl upholstery cleaner to deter the onset of cracking or drying. Avoid using any
abrasive cleaners or cleaners not intended for use on vinyl.
*Replace ripped or warn upholstery immediately.
*Keep sharp or pointed objects clear of all upholstery.
Decals:
*Inspect and familiarize yourself with any safety warnings or other user information posted on each decal.
Nuts and Bolts:
*Inspect all nuts and bolts for any loosening and tighten if needed.
*Go through a re-tightening sequence periodically to ensure that all hardware is tensioned proper.
Anti-Skid Surfaces:
*These surfaces are designed to supply secure footing and need to be replaced if they appear worn or become slippery.
Belts and Cables:
*Hoist uses only high quality belt, and mil-spec cables.
*Visually inspect the belts and cables for fraying, cracking, peeling or discoloration.
*While the machine is not in use, carefully run your fingers along the belt or cable to feel for thinning or bulging areas.
*Replace belts and cables immediately at the first signs of damage or wear. Do not use equipment until belts or cables have been replaced.
Belt and Cable Tension:
*Referring to the Owners Manual, when belts or cables are used check all bolts attachments to be sure they are properly attached.
*Check slack in cables and re-adjust cable tension if needed.
Seat Sleeves, Guide Rods:
*Wipe down adjusting tubes with a dust free rag before applying lubricant.
*Lubricate seat sleeves and Guide Rods with a Silicon or Teflon based lubricant spray.
Linear Bearings:
*Referring to the Owners Manual carefully disassemble the bearing from its housing and place a finger full of light grease (lithium, super lube,
PLEASE KEEP THIS FOR YOUR RECORDS
PAGE 16
OWNER'S MANUAL
CF-3461-2 ASSEMBLY

Pay attention to your breathing. Exhale when you exert is a general rule of
thumb. Never hold your breath.
Use this manual to guide you through the basic exercises you can perform on
your CF3461-2 HOIST® Fitness System. To gain maximum results and avoid
possible injury, consult a fitness professional to develop your complete exercise
program.
Always consult your physician before starting any exercise program.
To be successful in your exercise program, it is important to develop an
understanding of the basic principles of strength training. Now that you have
your CF3461-2 HOIST® Fitness System, it is only natural that you want to get
started immediately. First, determine a set of realistic goals and objectives for
yourself. By deciding on an exercise plan that is right for you prior to starting,
you will contribute significantly to your success.
Warm up properly before engaging in weight resistance training. Stretching,
yoga, jogging, calisthenics or other cardiovascular exercise can help prepare
your body for the heavier workload of lifting weights.
Learn how to perform the exercise correctly before using heavy weight.
Correct form is important to avoid injury and to ensure that you work the proper
muscle groups.
Know your limitations. If you are new to weight training or are embarking on
an exercise regimen after a long layoff, start slowly and build foundational
strength over a longer period of time.
WEIGHT TRAINING TIPS
Enjoy your CF3461-2 HOIST® Fitness System!
PAGE 17
OWNER'S MANUAL
CF-3461-2 ASSEMBLY

***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
CF-3461-2 ASSEMBLY
OWNER'S MANUAL
PAGE 18

Exercise
Totals
S = Sets R = Repetition per set W = Weight used
Date
RRWSRWWSRWSSRRWWSSRWWSWSRRWSRSRWWSR
WEIGHT TRAINING EXERCISE LOG
S
PAGE 19
OWNER'S MANUAL
CF-3461-2 ASSEMBLY