HOMCOM 824-003 User manual

ASSEMBLY INSTRUCTION
INcjd020V01_UK
824-003_824-004_824-005
READ AND SAVE THIS INSTRUCTION FOR FUTURE USE
220-240V~50/60Hz 45W
TOWER FAN

PAGE 2/7
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,
OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF
AND.OTHER BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO
COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
AND/OR PROPERTY DAMAGE!
IMPORTANT SAFETY INFORMATION
1. Read all instructions carefully before using the FAN.
2. Use this FAN only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electrical shock, or
injury to persons.
3. Remove the package and ensure that the FAN is undamaged. In case of
doubt do not use FAN and contact with your supplier.
4. Do not let children play parts of package.
5. Before use the FAN, check if the voltage marked on the rating label
corresponds to the mains in your home.
6. Extreme caution is necessary when the FAN is used by or near children or
Invalids and whenever the FAN is left operating unattended.
7. Avoid using extension cord as the extension cord may overheat and cause
a risk of fire.
8. Do not pull the power cord to disconnect with power source. Always grasp
the plug to pull out.
9. Do not insert any objects into the FAN as it may cause an electric shock or
injure or damage to the FAN. Do not block or tamper with the FAN in any
manner while it is in operation.
10. Do not leave the FAN unattended. Always unplug FAN when not in use.
11. This FAN is not intended for use in wet or damp locations. Never locate a
FAN where it may fall into a bathtub or other water container.
12. Do not use FAN outdoors.
13. Disconnect the fan from the mains power when not in use, and before
servicing or performing any maintenance.

PAGE 3/7
14. Always disconnect the fan from the power supply when moving it from one
location to another.
15. Keep the fan clean and maintain in good condition (use an authorized
service agent).
16. Use recommended parts only (non genuine parts may be dangerous, and
will invalidate your warranty).
17. When not in use store in a safe, dry, childproof location.
18. If the supply cord is damaged, it must be replaced by the manufacture, its
service agent or similarly qualified persons in order to avoid a hazard.
19. This appliance can be used by Children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without supervision.
WARNING : To avoid danger of electric shock, unplug from outlet when
not in use and before cleaning. If the supply cord is
damaged, it must be replaced by the manufactory or it’s
service agent or a similarity qualified person in order to
avoid a hazard.
WARNING : The Main Power Switch and the On/Off switch should not
be used as the sole means of disconnecting power. Always
unplug the power cord before servicing or moving the unit.

PAGE 4/7
PARTS NAME
ASSEMBLY
The base of the tower fan comes in two parts, which fit around the oscillation
base. Both parts fit easily together. The back half is the one with cut-outs for
the power supply cord.
1. First attach the front half of the base, aligning the holes in base with the
screw holes in the oscillation base, and leading the power cord through
the centre hole.
2. Then snap the back half of the base to the front half and secure with the
four screws (supplied)

PAGE 5/7
(Figure 1)
3. Thread the power supply cord through the two cut-outs at the bottom of
the base.
REMOTE CONTROL
1. Included a button cell battery (the type of battery CR2025).
The Remote Control Power button is labeled as such. All the functions
performed with the Remote Control work identically to the Manual Controls.
(FIGURE2)
OPERATION
The FAN may be operated by the manual controls located on the FAN (as
shown in FIGURE 3) or by your remote control (shown in FIGURE 2).
834-004/834-005 834-003

PAGE 6/7
(FIGURE 3)
1. Place the FAN on a stable flat surface. Plug the cord set into a
220-240V~A.C. electrical outlet.
2. POWER: Turn the FAN on by pressing the ‘POWER’ button; Turn the FAN
off by pressing the ‘POWER’ button again.
3. SPEED: You can adjust the fan speed to the desired level: low, medium, or
high by pressing ’SPEED’. The speed setting is displayed on the LED
screen (shown in FIGURE 4).
4. MODE: Pressing the’ MODE’ button will set the FAN into NORMAL,
NATURAL, and SLEEP mode.
5. TIMER: The fan is equipped with a timer that allows you to set it's length of
operation from 1 hour to 12 hours（834-004/834-005）, and from 0.5 hour to
7.5hours （834-003）.
6. OSC: Pressing the ‘OSC’ button will start and stop the oscillation function.
The symbol is displayed on the LED screen.
7. TEMP: Once the unit plug into the power socket or switch on, the FAN will
show the room temperature, and the ‘TEMP’ will change to ‘TIMER’ when the
timer is set.
8. Power save mode: when the ‘sleep’ mode or the ‘timer’ is on, the main
display will be off after 30 seconds, and you can press any keys to turn on the
display again.

PAGE 7/7
MAINTENANCE
1. This can only be done by an authorized service agent such as your local
Sealer dealer or any agent qualified to undertake electrical repairs.
2. If the unit requires external cleaning make sure it is switched off and
unplugged from the mains supply. Use a soft tissue or cloth for general
cleaning. To remove more persistent dirt or grime wipe down with a cloth that
has been dampened with warm soapy water. Do not use any solvents ( such as
thinners ) as these may damage the plastic casing.
Notice
1、This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
2、Children should be supervised to ensure that they do not play with
appliance.
3、If the supply cord is damaged, it must be replaced by the manufacture, its
service agent or similarly qualified persons in order to avoid a hazard.
9.DISPLAY LED- can be switched off temporarily by pressing the DISPLAY
button on the remote control or by pressing and holding the MODE button on
the control panel from more than 3 seconds,the display will light up again once
any control button is activated.
834-003
834-004/834-005 FIGURE 4