HOMCOM 824-062V90 User manual

0

1

2

3
EN READ CAREFULLY BEFOREATTEMPTING TOASSEMBLE, INSTALL,
OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT
YOURSELF AND.OTHER BY OBSERVING ALL SAFETY INFORMATION.
FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN
PERSONAL INJURYAND/OR PROPERTY DAMAGE !
IMPORTANT SAFETY INFORMATION
1. Read all instructions carefully before using the FAN.
2. Use this FAN only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,
electrical shock, or injury to persons.
3. Remove the package and ensure that the FAN is
undamaged. In case of doubt do not use FAN and contact
with your supplier.
4. Don not let children play parts of package.
5. Before use the FAN, check if the voltage marked on the
rating label corresponds to the mains in your home.
6. Extreme caution is necessary when the FAN is used by or
near children or Invalids and whenever the FAN is left
operating unattended.
7. Avoid using extension cord as the extension cord may
overheat and cause a risk of fire.
8. Do not pull the power cord to disconnect with power source.
Always grasp the plug to pull out.
9. Do not insert any objects into the FAN as it may cause an
electric shock or injure or damage to the FAN. Do not block
or tamper with the FAN in any manner while it is in
operation.
10. Do not leave the FAN unattended.
11. This FAN is not intended for use in wet or damp locations.
Never locate a FAN where it may fall into a bathtub or other

4
water container.
12. Do not use FAN outdoors.
13. Disconnect the fan from the mains power when not in use,
and before servicing or performing any maintenance.
14. Keep the fan clean and maintain in good condition (use an
authorized service agent).
15. Use recommended parts only (non genuine parts may be
dangerous, and will invalidate your warranty).
16. When not in use store in a safe, dry, childproof location.
17. This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
18. The back housing shall not dismantle, removal will be
dangerous .
19. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
20. Children should be supervised to ensure that they do not
play with the appliance.
WARNING :
The Main Power Switch and the On/Off
switch should not be used as the sole
means of disconnecting power. Always
unplug the power cord before servicing or
moving the unit.

5
WARNING :
To avoid danger of electric shock, unplug
from outlet when not in use and before
cleaning. If the supply cord is damaged, it
must be replaced by the manufactory or it’s
service agent or a similarity qualified
person in order to avoid a hazard.
PARTS NAME
ASSEMBLY
1. Take out the two parts of the base from packing box. Then, align the
centers of the two parts of the base and place them in a crossed form.
Rotate one of the two bases to align its hole site and make it stuck
correctly (Fig 1).

6
(Fig 1)
2. Put the wire in the recess, then fix the base on the fan body with four
screws (included), and turn the screws clockwise (Fig 2).
(Fig 2 )
REMOTE CONTROL
1. Included a button cell battery (the type of battery CR2025).
2. The remote control power button is labeled as such.All the functions
performed with the remote control work identically to the manual controls.
( Fig 3).
( Fig 3) ( Fig 4)

7
OPERATION
The FAN may be operated by the manual controls located on the FAN (as
shown in Fig 4 ) or by your remote control (shown in Fig 3) .
1. Place the FAN on a stable flat surface. Plug the cord set into a 220-240V~
electrical outlet. Plug on the FAN, existing room temperature will be
displayed at display panel.
2. POWER : Turn the FAN on by pressing the ‘POWER’ button; Turn
the FAN off by pressing the ‘POWER’ button again.
3. SPEED :You can adjust the fan speed to the desired level: low,
medium, or high by pressing ‘SPEED’ . The speed setting is displayed on
the LED panel (shown in Fig. 5) .
4. MODE : Pressing the ‘MODE’ button will set the FAN into NORMAL
mode, NATURAL mode,SLEEP mode and Child mode
- NORMAL Mode : Fan will start work at any speed you set up.
- NATURAL Mode : Fan will start work at low speed(5s)→medium
speed(5s)→high speed(5s)→medium speed(5s), it works as per this
recycle.
- SLEEP Mode : 1）If you set the mode at high speed, fan will work
at high speed at 30 mins, then transfer to medium speed at 30 mins and
transfer to low speed until fan stop working. 2）If you set the mode at
medium speed, fan will work at medium speed at 30 mins, then transfer to
low speed until fan stop working. 3）If you set the mode at low speed, fan
will work at low speed until fan stop working. The LED Display will turn off
if you don’t control the fan in 30 seconds, touch any button to turn on the
display.

8
- Child Mode : Fan will auto. Set up timer at 3 hours, oscillation
function will start.And it will work at high speed at 15 minutes, transfer
to medium speed at 15 minutes, then transfer to low speed until it take
off. You can take off oscillation function by manual. The LED Display
will turn off if you don’t control the fan in 30 seconds, touch any button to
turn on the display.
5. TIMER : The fan is equipped with a timer that allows you to set its
length of operation from 1 hour to 12 hours.The LED Display will turn off if
you don’t control the fan in 30 seconds, touch any button to turn on the
display.
6. OSCILLATION : Pressing the ‘OSC’ button will start and stop the
oscillation function. The symbol is displayed on the LED panel.(shown in
Fig 5)
( Fig 5)
7. DISPLAY :Can be switched off temporarily by press the LED
button on the remote or by pressing and holding the SPEED button on the
control panel for more than 3 seconds, the display will light up again once
any control button is activated.
8. Cable hook: The cable hook is packed in the user manual, take it out
and install on the back side of the fan. The power cord can be hanged at
the cable hook when the fan is not in used.(Fig 6) .

9
(Fig 6)
MAINTENANCE
1. This can only be done by an authorized service agent such as your local
Sealer dealer or any agent qualified to undertake electrical repairs.
2. If the unit requires external cleaning make sure it is switched off and
unplugged from the mains supply. Use a soft tissue or cloth for general
cleaning. To remove more persistent dirt or grime wipe down with a cloth that
has been dampened with warm soapy water. Do not use any solvents ( such
as thinners ) as these may damage the plastic casing.
Correct Disposal of this product
This marking indicates that this product should not be
disposed with other household wastes throughout the
EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of
material resources. To return your used device, please
use the return and collection systems or contact the
retailer where the product was purchased. They can
take this product for environmental safe recycling.