HOMCOM CTF4202TR-L User manual

1
ASSEMBLY INSTRUCTION
IN231000485V01_UK
824-075V70
Tower fan with cooling
Model No.: CTF4202TR-L
220-240V~50-60Hz 60W
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

2
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR
MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHER BY
OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY
DAMAGE!
IMPORTANT SAFETY INFORMATION
1.Read all instructions carefully before using the FAN.
2.Use this FAN only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electrical shock, or injury to persons.
3.Remove the package and ensure that the FAN is undamaged. In case of doubt do not
use FAN and contact with your supplier.
4.Do not let children play parts of package.
5.Before use the FAN, check if the voltage marked on the rating label corresponds to the
mains in your home.
6.Extreme caution is necessary when the FAN is used by or near children or Invalids and
whenever the FAN is left operating unattended.
7.Avoid using extension cord as the extension cord may overheat and cause a risk of fire.
8.Do not pull the power cord to disconnect with power source. Always grasp the plug to pull
out.
9.Do not insert any objects into the FAN as it may cause an electric shock or injure or
damage to the FAN. Do not block or tamper with the FAN in any manner while it is in
operation.
10.Do not leave the FAN unattended. Always unplug FAN when not in use.
11.This FAN is not intended for use in wet or damp locations. Never locate a FAN where it
may fall into a bathtub or other water container.
12.Do not use FAN outdoors.
13.Disconnect the fan from the mains power when not in use, and before servicing or
performing any maintenance.
The Main Power Switch and the On/Off switch should not be used
as the sole means of disconnecting power. Always unplug the
power cord before servicing or moving the unit.
WARNING :
14.Keep the fan clean and maintain in good condition (use an authorized service
agent).Unplug the appliance during filling and cleaning.
15.Use recommended parts only (non genuine parts may be dangerous, and will invalidate
your warranty).
16.When not in use store in a safe, dry, childproof location.
17.This appliance can be used by Children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by children without
supervision.
18.Be aware that high humidity levels may encourage the growth of biological organisms in
the environment.
19.Do not permit the area around the appliance to become damp or wet. If dampness
occurs, turn the output of the appliance down. If the appliance output volume cannot be
turned down, use the appliance intermittently. Do not allow absorbent materials, such
as carpeting, curtains, drapes, or tablecloths, to become damp.
20.Empty and clean the appliance before storage. Clean the appliance before next use.
21.The back housing shall not dismantle, removal will be dangerous .

3
22.This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
23.Children should be supervised to ensure that they do not play with appliance.
To avoid danger of electric shock, unplug from outlet when not in
use and before cleaning. If the supply cord is damaged, it must be
replaced by the manufactory or it’s service agent or a similarity
qualified person in order to avoid a hazard.
WARNING :
CONTROLS AND COMPONENTS
1: Control panel:
a: Power on/off button b: Child lock button c: Cooling button
e: Timer button f: Oscillation button g: Speed button
2: Handle & Remote control storage 3: Cable hook 4: LED display
5: Air outlet 6: Air intake 7: Back housing 8: Water tank latch
9: Water scale 10: Water tank 11: Water tank handle 12: Base 13: Ice box
ASSEMBLY
Take out the two parts of the base from packing box. Then, align the centers of the two
parts of the base and place them in a crossed form. Rotate one of the two bases to
align its hole site and make it stuck correctly (Fig. 1).
(Fig. 1)

4
.
Cable Hook: Hanging the power cord at cable hook when the fan is not be used.(Fig. 3)
Water filling and water tank clearance
ATTENTION
1.Please be sure the plug is taken off when you fill the water or cleaning.
2.Please clean the water that in the water tank when you do not use the product.
3.Turn the water tank latch to right or left at 90 degree to open the water tank. Then fill
the water into the water tank. (Fig. 4).
4.When fill the water, do not exceed ‘MAX’ level at water scale. At cooling mode, keep
the water at least at ‘MIN’ level. (Fig. 5)
5.Clean Water tank: Pull out the water tank to find water pump, then gently pinch the
pressure plate of the water pump, and take out the water pump and clean the water
tank directly ( Fig. 6)
6.Use the brush or tool to clean the water tank.
7.Don’t clean transducer by any metal or stiffness material or scrape it to avoid any
damage
8.Don't put acid, alkalescency, bleacher scour into water tank to avoid damage
9.Do not spray the water onto control panel and its surrounding, to avoid electrical
leakage accidents.
10. Do not open the cover of Ice Box, to avoid its leakage. The Ice Box is environmental
protection material that would storage in refrigerator and would use it repeatedly.
Fix the base on the fan body with four screws ( included), with a screwdriver, wise it
clockwise ( Fig. 2).
(Fig. 2)
(Fig. 3)

5
(Fig. 4) (Fig. 5)
Water tank
latch
(Fig. 6)
Both sides of the buckle
Water pump

6
REMOTE CONTROL
1.Included a button cell battery (the type of battery CR2025). (Note: Please take out
the insulation film under the battery for first time use.) (Fig.7)
The Remote Control Power button is labeled as such(Fig.8). All the functions
performed with the Remote Control work identically to the Manual Controls.
(Fig. 7)
(Fig. 8) (Fig. 9)
(Fig. 10)

7
OPERATION
The FAN may be operated by the manual controls located on the FAN or by your remote
control ( Fig. 8 & 9).
1.Place the FAN on a stable flat surface. Plug the cord set into a 220-240V~ electrical
outlet. Plug on the FAN, existing room temperature will be displayed at LED display.
2.POWER : Turn the FAN on by pressing the ‘POWER’ button; Turn the FAN off by
pressing the ‘POWER’ button again.
3.SPEED : You can adjust the fan speed to the desired level: low, medium, or high
by pressing ‘ ’. The speed setting is displayed on the LED display. (Fig. 10)
4.MODE : Pressing the ‘ ’button will set the FAN into NORMAL, NATURAL,
SLEEP and CHILD mode.
- NORMAL Mode: Fan will start work at any speed you set up.
- NATURAL Mode : Fan will start work at low speed(5s)→medium speed(5s)→high
speed(5s)→medium speed(5s), it works as per this recycle.
- SLEEP Mode : 1) If you set the fan at high speed, fan will work at high speed at 30
mins, then the fan will transfer to medium speed and work at 30 mins, later the fan
transfer to low speed and keep working until the fan stop working.
2) If you set the mode at medium speed, fan will work at medium speed at 30 mins, then
the fan will transfer to low speed and keep working until it stop working.
3) If you set the mode at low speed, fan will work at low speed until the fan stop working.
The LED display will turn off if you don’t control the fan in 30 seconds, touch any button
to turn on the display.
- CHILD Mode : Fan will auto. Set up timer at 3 hours and oscillation function will
start. The fan will work at high speed for 15 minutes, and it will transfer to medium speed
at 15 minutes, then it will transfer to low speed until it take off. You can take off
“oscillation function” manually. The LED display will turn off if you don’t control the fan in
30 seconds, touch any button to turn on the display.
5. TIMER : The fan is equipped with a timer that allows you to set its length of
operation from 1 hour to 12 hours. The LED display will turn off if you don’t control the
fan in 30 seconds, touch any button to turn on the display.
6. OSCILLATION : Pressing the ‘ ’ button will start and stop the oscillation
function. The symbol is displayed on the LED display.
7. COOLING : Press ‘ ’ button to turn on the cold air function. Press button again
to turn off. If you want to operate the unit with water for better cooling, pull out the
water tank and fill it up to the MAX mark at the most. Take care when doing so, to
make sure, that no water enters the product, e.g. through the air inlet.

8
ATTENTION ABOUT ICE BOX
Then put a ice box in the water tank ( the ice box needs to be frozen for more than 3
hours), and the cooling effect is better ( Note: when the water tank is short of water, it is
forbidden to use, please add water in time).
Do not open the cover of Ice Box, to avoid its leakage. The Ice Box is environmental
protection material that would storage in refrigerator and would use it repeatedly.
8. DISPLAY :Can be switched off temporarily by press the LED button on the
remote or by pressing and holding the SPEED button on the control panel for more
than 3 seconds, the display will light up again once any control button is activated.
9. Child lock : press ‘ ’ button to activate the child lock function. All controls
cannot be used. Press and hold for 3 seconds to cancel the child lock function and
restore normal control.
WARNING of Low water: when turn on the fan in cooling condition, and the water at low
scale, the alarm will sound 3 times, Cooling Icon will flash. And Cooling function stop
working. It’s need fill water and reset cooling function.
MAINTENANCE
1.This can only be done by an authorized service agent such as your local Sealer dealer
or any agent qualified to undertake electrical repairs.
2. If the unit requires external cleaning make sure it is switched off and unplugged from
the mains supply. Use a soft tissue or cloth for general cleaning. To remove more
persistent dirt or grime wipe down with a cloth that has been dampened with warm
soapy water. Do not use any solvents ( such as thinners ) as these may damage the
plastic casing.
Correct disposal of this product
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm
to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe
recycling.

9