Home Styles 88 5076 943 User manual

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
Hardware List
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
M4x25
Machine Screw
2 pcs.
Cam Lock Screw
8 pcs.(+1 extra)
Cam Lock
8 pcs.(+2 extra)
M3.5x19
Wood Screw
9 pcs. (+1 extra)
Knob
2 pcs.
Q.
Post
1 pc.
Also need the parts in cartons 88 5076 942 and 88 5077 941 or 88 5077 944
88 5076 394
Kitchen Island
M.
Base
1 pc.
N.
Side Panel
2 pcs.
O.
Back Panel
2 pcs.
R.
Post
1 pc.
S.
Post
1 pc.
P.
Post
1 pc.
Mx635
Head Cap Bolt
22 pcs. (+1 extra)
Adjustable Pin
32 pcs. (+1 extra)

Assembly Instructions 2/5
Figure 2
Wood Screw
A
B
Q
Cam Lock Screw
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Cam Locks in the future.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
Figure 1
STEP 2
Insert Cam Lock Screws into the pre-drilled holes of Posts (P), (Q), (R) and (S).
STEP 1
Place Top (A) and Leaf Top (B)
upside dow on a soft cloth.
Insert Cam Lock
Screws into the
pre-drilled holes of Top (A)
and tighten. (See Figure 1)
Attach Leaf Top (B) to Top (A) with Wood Screws.
(See Figure 2) Cam Lock Screw
S
R
P
Cam Lock Screw

Assembly Instructions 3/5
STEP 3
Remove the drawers from
Upper Unit (C).
STEP 4
Attach Upper Unit (C) to Top (A) with
Head Cap Bolts and Cam Locks.
(See Figures 3 and 4)
Figure 3
Figure 4
Cam Lock
Cam Lock
Head Cap Bolt
Head Cap Bolt
STEP 5
Attach Post (Q) to Base (M) with
Head Cap Bolts.
Attach Back Rail (H)
to Post (Q) with Cam Lock.
Attach Back Piece (I) to Back
Rail (H).
Slide Back Panels (O) into position.
Attach Back Rail (H)
to unit with Cam Lock.
Attach Post (S) to unit with
Head Cap Bolts and Cam Locks.
C
C
A
M
S
Q
H
I
O
H
O

Assembly Instructions 4/5
STEP 6
Attach Post (P) and Middle Panel (G) to unit with Head Cap Bolts.
Attach Front Rail (D) to unit with Cam Lock.
Attach Post (R) to unit with Head Cap Bolts and Cam Lock.
STEP 7
Slide Panels (N)Side
into position.
P
G
D
R
N
N
Cam Lock
Head Cap Bolt

Assembly Instructions 5/5
Head Cap Bolt
Figure 5
STEP 8
Attach Wood Supports (J) to
unit with Head Cap Bolts.
Attach top unit to base unit with
Head Cap Bolts.
Figure 7
STEP 9
Insert the Adjustable Pins into
the side panels atand middle
the desired level.
Place Shelves (K) and (L) into
position.
Attach Knobs to drawers with machine
screws and slide drawers into position.
(See Figure 5)
Attach Doors (E) and (F) to unit by sliding
the door lift hinges into the side panel lift hinges.
(See Figure 6)
To level the unit, adjust the adjustable levelers on the bottom of unit. (See Figure 7)
Figure 6
L
L
L
KL
E
K
K
K
Adjustable Pin
F
J
J