Home Styles 88 5081 101 User manual

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
E.
Base
1 pc.
A.
Top
1 pc.
G.
Back Stretcher
1 pc.
H.
Back Panel
1 pc.
I.
Back Panel
1 pc.
J.
Back Strip
1 pc.
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
F.
Front Rail
1 pc.
88 5081 101
Entertainment Credenza
For assembly see instructions in carton 88 5 102081
M.
Shelf
2 pcs.
Hardware List
Adjustable Pin
8 pcs.(+1 extra)
Pull Handle
2 pcs.
M4x12
Machine Screw
2 pcs.
Bolt
for Back Panel
2 pcs.(+1 extra)
M3x16
Wood Screw
for Magnet
4 pcs.(+1 extra)
M3x16
Wood Screw
for Hinge
12 pcs.(+1 extra)
Magnet
2 pcs.

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
B.
Side Panel
.1 pc
C.
Side Panel
1 pc.
D.
Middle Panel
.1 pc
L.
Door
1 pc.
K.
Door
1 pc.
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
88 5081 102
Entertainment Credenza
Also need the Parts and Hardware in carton 88 5 101081

Assembly Instructions 2/5
STEP 1
STEP 2
Attach Side Panel (C) and Middle Panel (D)
to Base (E), then flip the Locks.
(See Figures 1 and 2)
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
* Use a soft cloth between these parts and the floor.
D
E
Figure 1
Figure 2
Figure 3
C
F
Attach Magnets to Front Rail (F) with Wood Screws for Magnet.
(See Figure 3)
Wood Screw
for Magnet
Magnet

Assembly Instructions 3/5
STEP 4
STEP 3
Slide Back Panel (I), Back Strip (J)
and Back Panel (H) into position.
Insert Bolts for Back Panel into the pre-drilled holes of Back Panels (H)
and (I). (See Figure 4)
H
I
J
Bolt
for Back Panel
Figure 4
G
F
B
Attach Front Rail (F) and Back Stretcher (G) to unit, then flip the Locks.
Attach Side Panel (B) to unit, then flip the locks.

Assembly Instructions 4/5
A
K
L
MM
Attach Top (A) to the unit, then flip the Locks.
Insert Adjustable Pins into side panels and middle panel at the desired level. (See Figure 5)
Place Shelves (M) into position.
Attach Doors (K) and (L) to unit with Wood Screws for Hinges. (See Figure 6)
Assemble Pull Handles to Doors (K) and (L) with Machine Screws. (See Figure 7)
To level the unit, adjust the adjustable levelers on the bottom of legs. (See Figure 8)
Note : Unit must be level to work properly.
Figure 5 Figure 6 Figure 7
Figure 8
STEP 5

Assembly Instructions 5/5
Wood Screw
Wall Screw
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Drill 3/8” hole in wall
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
Wood Screw
Wall Screw
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Drill 3/8” hole in wall
Top of unit
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
M3.5x16
Wood Screw
1 pc.(+1 extra)