Home Styles 88 5053 22 User manual

Hardware List
Part List
88 5053 22
IMPORTANT
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Console Table
Tool(s) required for assembly: Level
Hex Wrench
1 pc.
M6x16
Head Cap Bolt
32 pcs. (+1 extra)
Spring Washer
32 pcs. (+1 extra)
Flat Washer
32 pcs. (+1 extra)
Adjustable Pin
4 pcs. (+1 extra)
Small Wrench
1 pc.
A.
Top
1 Pc.
D.
Shelf
1 Pc.
G.
Base
1 Pc.
C.
Side Frame
1 Pc.
B.
Side Frame
1 Pc.
E.
Stretcher
2 Pcs.
F.
Stretcher
2 Pcs.

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
Head Cap Bolt
Spring Washer
Flat Washer
E
E
STEP 1
Attach Stretchers (E) and (F)
to Side Frame (B) with
Flat Washers, Spring Washers and
Head Cap Bolts, tightening the
bolts only half way. (See Figure 1)
Attach Side Frame (C) to unit with
Flat Washers, Spring Washers and
Head Cap Bolts, tightening the
bolts only half way.
Figure 1
STEP 2
Place Top (A)
upside down on a soft cloth.
Attach unit to Top (A)
with Flat Washers, Spring Washers,
and Head Cap Bolts, tightening the
bolts only half way. (See Figure 2)
Figure 2
A
F
F
B
C

Assembly Instructions 3/3
STEP 3
Attach Base (G) to unit
with Flat Washers, Spring Washers
and Head Cap Bolts, tightening the bolts only half way.
Tighten all Bolts used in all steps.
STEP 4
Turn the unit to its’ upright position.
Insert two Adjustable Pins into back of unit at desired level.
Place Shelf (D) into position, then insert two Adjustable Pins into front of unit.
To level the unit, adjust the adjustable levers on the bottom of unit. (See Figure 3)
Note: Unit must be level to work property.
Figure 3
Adjustable Pin
D
G

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319