Home Styles 88 5080 06 User manual

Part List
Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5080 06
Media Console
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Spring Washer
1 pc.(+1 extra)
Flat Washer
1 pc.(+1 extra)
A.
Top
1 pc.
B.
Side Frame
.1 pc
C.
Side Frame
1 pc.
D.
Shelf
.1 pc
F.
Back Panel
1 pc.
G.
Back Panel
1 pc.
E.
Base
1 pc.
M6x16
Head Cap Bolt (short)
12 pcs.(+1 extra)
M6x25
Head Cap Bolt
1 pc.(+1 extra)
M3.5x13
Wood Screw
4 pcs.(+1 extra)
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.

STEP 1
STEP 2
Assembly Instructions 2/4
Attach Top (A), Shelf (D) and Base (E) to Side Frame (B)
with Head Cap Bolts (short), tightening the bolts only half way.
(See Figure 1)
Figure 1
Attach Side Frame (C) to unit with Head Cap Bolts (short),
tightening the bolts only half way.
Tighten all Head Cap Bolts used in entire assembly.
Head Cap Bolt
(short)
IMPORTANT
* Do not tighten all the Head Cap Bolts until the entire unit is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
BA
D
E
C

STEP 3
Assembly Instructions 3/4
Turn the unit to its’ upright position.
Slide Back Panels (F) and (G) into place.
Attach Head Cap Bolt, Spring Washer and Flat Washer to unit. (See Figure 2)
Attach 4X Wood Screws to unit. (See Figure 3)
To level the unit, adjust the adjustable levelers on the bottom of side frames. (See Figure 4)
Note: Unit must be level to work properly.
F
G
Flat Washer
Spring Washer
Head Cap Bolt
Wood Screw
Figure 2 Figure 4
Figure 3

Assembly Instructions 4/4
Wall Screw
M4x16
Machine Screw
2 pcs.(+1 extra)
Anchor
2 pcs.(+1 extra)
Bracket
4 pcs.(+1 extra)
Tipover Restraint
2 pcs.(+1 extra)
Hardware List
Drill 3/8” holes in wall
Top of unit
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
2 pcs.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill two holes in wall3/8”
at the appropriate location.
Insert Anchors into the wall holes
and attach Brackets with Wall Screws.
Attach Brackets at pre-drilled holes at top
of unit with Machine Screws.
Use Tipover Restraints to secure Brackets
on unit to Brackets on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
Machine
Screw