Home Styles 20 05008 0941 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Kitchen Island
IMPORTANT
Cam Lock
15 pcs. (+2 extra)
Cam Lock Screw
15 pcs. (+1 extra)
1/2”
Round Head Screw
4 pcs. (+1 extra)
3/4”
Round Head Screw
8 pcs. (+1 extra)
1”
Round Head Screw
16 pcs. (+1 extra)
M6x35
Head Cap Bolt
20 pcs. (+1 extra)
Magnet
2 pcs.
M4x25
Machine Screw
4 pcs.
Flat Washer
8 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
Patent 8,584,600 B2
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
L.
Back Upright
1 pc.
Cartons 20 05020 0942 and 20 05008 0943 or 20 05009 0943 are also needed for assembly.
Tool(s) required for assembly: LevelPhillips screwdriver,
Refer to later page(s) of these
instructions for drawer assembly.
Small Hex Wrench
1 pc.
3/4”
Flat Head Screw
12 pcs. (+1 extra)
H.
Back Rail
1 pc.
G.
Back Rail
1 pc.
F.
Front Rail
1 pc.
E.
Front Rail
1 pc.
I.
Shelf
4 pcs.
M.
Door
1 pc.
N.
Door
1 pc.
K.
Back Panel
2 pcs.
J.
Base
1 pc.
O.
Drawer
2 pcs.
Hex Wrench
1 pc.
Knob
4 pcs.
20 05008 0941

Assembly Instructions 2/9
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 2
Attach Magnets to Front Rail (F) with 1/2” Round Head Screws into pre-drilled holes.
(See Figure 2)
Figure 2
1/2” Round Head Screw
Magnet
F
Cam Lock Screw
Figure 1
G
L
H
J
B
C
F
E
STEP 1
Insert Cam Lock Screws into
pre-drilled holes in Side Panels (B), (C),
Front Rails (E), (F), Back Rails (G), (H),
Base (J) and Back Upright (L), then tighten.
(See Figure 1)

Assembly Instructions 3/9
Figure 3
B
C
E
F
K
K
D
G
H
L
STEP 3
Attach Middle Panel (D) to Back Rails (G), (H)
and Back Upright (L) with Cam Locks.
(See Figure 3)
Slide Back Panels (K) into position.
Attach Front Rails (E) and (F) to unit with Cam Locks.
STEP 4
Attach Side Panels (B) and (C)
to unit with Cam Locks.
Cam Lock
Cam Lock

Assembly Instructions 4/9
STEP 5
Attach Base (J) to unit with Cam Locks,
Flat Washers and Head Cap Bolts.
Tighten bolts with Hex Wrench.
(See Figure 4)
STEP 6
Turn unit to its upright position.
Attach Post Assemblies (P) and (Q)
to unit with Head Cap Bolts.
Tighten bolts with Hex Wrench.
Figure 4
P
Q
J
Flat Washer
Head Cap Bolt
Cam Lock
Head Cap Bolt

Assembly Instructions 5/9
Figure 6 Figure 7Figure 5
STEP 7
Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 5)
Note: Unit must be level to proceed.
Insert 3/4” Round Head Screws into pre-drilled holes in back of unit, then tighten.
Note: Unit must be level before tightening these screws.
Attach Doors (M) and (N) to unit by sliding door hinges into side panel hinges. (See Figure 6)
Attach Knobs to Doors (M) and (N) with Machine Screws. (See Figure 7)
3/4” Round Head Screw
M
N
Knob
Machine Screw

Assembly Instructions 6/9
STEP 9
Place Top (A1) and Leaf Top (A2)
upside down on a soft cloth.
Attach Leaf Top (A2) to Top (A1)
with 3/4” Flat Head Screws
into pre-drilled holes.
(See Figure 8)
Figure 8
A2
A1
3/4” Flat Head Screw
I
I
I
I
Adjustable Pin
STEP 8
Insert Adjustable Pins into side panels
and middle panel at desired level.
Slide Shelves (I) into position.

Assembly Instructions 7/9
STEP 12
Attach Knob with Machine Screw.
Drawer (O)
STEP 10
Attach Drawer Front (O1) and
Drawer Back (O2) to Drawer Side (O3)
with 1” Round Head Screws.
STEP 11
Slide Drawer Bottom (O5) into groove.
Attach Drawer Side (O4) to unit
with 1” Round Head Screws.
Part List
O1.
Drawer Front
2 pcs.
O2.
Drawer Back
2 pcs.
O3.
Drawer Side
2 pcs.
O4.
Drawer Side
2 pcs.
O5.
Drawer Bottom
2 pcs.
Roller at back
1” Round Head Screw
O2
O5
O3
O1
Machine Screw
Knob
1” Round Head Screw
O4

Assembly Instructions 8/9
Figure 9
STEP 13
Attach Top (A1) to unit with Flat Washers and Head Cap Bolts.
(See Figure 9)
Slide Drawers (O) into position.
O
O
A1
Flat Washer
Head Cap Bolt

Assembly Instructions 9/9
STEP 14
When leaf top is down, it should be oriented vertically.
If it is not vertical and adjustment is desired,
turn the adjuster on adjuster block on back rail.
(See Figure 10)
STEP 15
Lift up leaf top.
STEP 16
Holding leaf top up, pull out a back post
from unit; then pull out other back post.
Note: Unit must be level to work properly.
Top Extension Instructions
Adjuster Block
Figure 10

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319