Honeywell 138560.10 User manual

GB
FloodLED IP66
147mm
108mm
146mm 102mm
Dimensional Drawings:
Step 3: Make a hole in the center of the rubber gasket by using a small screwdriver. Pass the mains cable
through the rubber gasket. Always use in any case round mains cable, with a diameter of 5-10mm.
ATTENTION!! The cable must not be deformed in any way (This requirement is important to ensure the
IP rating).
Step 2: Install the bracket to the bottom part of the luminaire, with the supplied screw (long one) and nut.
Step 4: The user can select one of the 3 available minimum autonomy durations: 1 hour, 3 hours and 8
hours. The selection must be done while the luminaire is disconnected from AC and battery supplies. The
selection is achieved through Switches 2 & 3 of DS1. Switch 1 is not used. Two additional labels are included
in the package one for 3 hours duration (180) and one for 8 hours duration (480). The installer must cover
the default 1 hour (60). printing. Please take notice of the orientation of the label.
Step 1: Unfasten the two retaining screws to dismantle the luminaire.
Step 5: Connect the mains cable to the therminal blocks: L for live wire, N for neutral and PE for the
ground wire. For pernament maintained operation switch number 4 must be in ON position. For non-
maintained operation, switch number 4 must be in OFF position. For controlled maintained operation of the
lamp, connect L1 to an external switch and switch number 4 of the DS1 must be in OFF position. Power
2
supply cables cross section should be 0.8 – 3 mm . Install the supplied plastic tie anchor with the screws, to
fasten securely the power cable, in order to anchor it.
Installation:
3
N PEL
L1
N
L
PE N PEL
L1
N
L
PE
Pernament Maintained Operation
Non-Maintained Operation
Controlled Maintained
Operation of the Lamp
ON
1 2 3 4
Maintained operation
(default position)
ON
1 2 3 4
ON
1 2 3 4
Non-maintained operation Controlled Maintained
Operation of the Lamp
External
Switch
2
DS1
5
1
4 5
Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com
N
L
L1 PE
Plastic Ties
Cable Holes
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
1h
(default position)
3h 8h

GB
Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com
Selftest functions
Every 15 days the luminaire will perform an emergency operation test. This will turn on the light source for
approximately 3 seconds. The green LED will flash during this test sequence.
Every 6 months the luminaire will perform a battery condition test. The test will last for the chosen
autonomy. The light source will be lit and the green LED will flash during this test sequence.
Note: When using Wireless communication, the frequencies and schedules for tests will instead be
determined by the connected PC software.
Important notice when installing luminaires within the same area!!!
The FloodLED is a self-contained maintained/non-maintained luminaire with selftest function.
To avoid that luminaires perform their battery test at the same day, connect the battery packs with more
than 1,5 minutes inbetween.
Step 6: Place the battery's connector to the corresponding connector
on the PCB.
Step 7: In case you use a module connect it on the PCB.
Note! FloodLED supports only the Wireless module.
Step 9: Mount the bracket to the wall or to the ceiling.
Step 8. Refit the luminaire to the bottom cover and fasten the two
removed screws.
8
9
7
6
Indicator LEDs
LED Status explanation
Description
GREEN
RED
Normal
Charging (battery test not possible while charging)
Mains off, battery not connected or charger fault
Battery fault
Battery test (Duration: 1h,3h,8h)
Light source test (Duration: 3s)
Light source fault
Battery fault and light source fault
Off On Slow Blink Fast Blink

GB
Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com
Technical description
Part no.:
Battery (LiFePO ):
4
Battery Protection: Overcharge protection / full discharge protection
Maximum Power Consumption:
Operation Voltage:
FloodLED 10Y 138h
5.3W / 5.7VA
220-240V AC, 50-60 Hz
138560.10
3.2V / 2Ah
16hours
Produced in accordance with:
Relative Humidity:
Charging Time:
Technical lifetime (light source):
Lumen output, normal:
> 100000 hours
400lm
1h / 3h / 8h manually selected (default 1h)
Degress of cover protection:
Emergency Mode Duration:
Lumen output, emergency: 1h: 390lm / 3h: 190lm / 8: 80lm
Weight:
Expected Battery Lifetime:
Controlgear classification in accordance with IEC 62034: with automatic test function
510 gr
10 years
At the end of their useful life the packaging, product & batteries
should be disposed of via a suitable recycling centre. Do not
dispose of with your normal household waste. Do not burn.
Swivel angles
Ambient Temperature Range:
o o
Up-Down: -90 to +90 o o
Right-Left: -70 to +70
o
5 to 40 C
Up to 95%
IP66
EN 60598-1, EN 60598-2-22, EN 55015
EN 61547, EN 61000-3-2, EN 61000-3-3
Note: In case of battery replacement, this must be replaced with parts of the same type and characteristics.
The replacement must be performed by the manufacturer or a competent person.
Note: In case of mains power disconnection for a period of more that two months, the battery must be
disconnected.
Note: If the supply cable of the luminaire is damaged, it shall exclusively be replaced by a competent person
in order to avoid hazard.
The light source contained in this luminary shall only be replaced by the manufacturer, or his agent,
or a similar qualified person.
NOTE! The light source is non-user replaceable.