Honeywell AMM-4SF User manual

AMM-4SF Interface Module
INSTALLATION AND MAINTENANCE INSTRUCTIONS
BEFORE INSTALLING
This information is included as a quick reference installation guide. Refer to
the control panel installation manual for detailed system information. If the
modules will be installed in an existing operational system, inform the opera-
tor and local authority that the system will be temporarily out of service. Dis-
connect power to the control panel before installing the modules.
NOTICE: This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The AMM-4SF Interface Module is intended for use in intelligent, two-wire
systems, where the individual address of each module is selected using the
built-in rotary switches. This module allows intelligent panels to interface and
monitor two-wire conventional smoke detectors. It transmits the status (nor-
mal, open, or alarm) of one full zone of conventional detectors back to the
control panel. All two-wire detectors being monitored must be UL compatible
with this module. AMM-4SF is capable of handling more than one detector in
alarm condition.
COMPATIBILITY REQUIREMENTS
To ensure proper operation, this module shall be connected to a compatible
Gamewell-FCI system control panel only (list available from Gamewell-FCI).
Please refer to Gamewell-FCI’s document #9000-0427 for full list of compat-
ible devices.
FIGURE 1. CONTROLS AND INDICATORS
C1059-00
SPECIFICATIONS
Normal Operating Voltage: 15 to 32 VDC
Maximum Current Draw: 5.1 mA (LED on)
Average Operating Current: 255 µA (LED flashing - in Velociti mode); 230 µA (LED flashing - in CLIP mode)
EOL Resistance: 3.9K Ohms
Maximum IDC Wiring Resistance: 25 Ohms
IDC Supply Voltage (between Terminals T10 and T11)
Regulated DC Voltage: 24 VDC power limited
Ripple Voltage: 0.1 Volts RMS maximum
Alarm Current: 90 mA per module
Standby Current: 13 mA Maximum @24 VDC
Temperature Range: 32˚F to 120˚F (0˚C to 49˚C)
Humidity: 10% to 93% Non-condensing
Dimensions: 4.5˝ H × 4 W × 1.25˝ D (Mounts to a 4˝ square by 2.125˝ deep box.)
Accessories: SMB500 Electrical Box
MOUNTING
The AMM-4SF mounts directly to 4-inch square electrical boxes. (See Figure 2.)
The box must have a minimum depth of 2.125 inches. Surface mounted elec-
trical boxes (SMB500) are available from Gamewell-FCI.
WIRING
NOTE: All wiring must conform to applicable local codes, ordinances, and
regulations. This module is intended for power-limited wiring only.
1. Install module wiring in accordance with the job drawings and appropri-
ate wiring diagrams.
2. Set the address on the module per job drawings.
3. Secure module to electrical box supplied by installer. (See Figure 2.)
FIGURE 2. MODULE MOUNTING
ISOLATED
QUADRANT
C1066-00
I56-3552-006
Velociti ®Series
12 Clintonville Road
Northford, CT 06472-1653
Phone: [phone]; Fax: [phone]
www.gamewell-fci.com
1 I56-3552-006
7/1/2022

FIGURE 3. INTERFACE TWO-WIRE CONVENTIONAL DETECTORS, NFPA CLASS B
(+)
(–)
(+)
(–)
(+)
(–)
+
–
LISTED BATTERY-BACKUP SWITCHED
REGUALTED DC POWER SUPPLY
POWER TO THE INTERFACE
MODULE MUST BE EXTERNALLY
SWITCED TO RESET THE
DETECTORS. A RELAY CONTROL
MODULE CAN BE USED TO SWITCH
POWER FROM A STANDARD POWER
SUPPLY (SEE FIGURE 5).
OPTIONAL BRANCH CIRCUIT
TO NEXT INTERFACE
MODULE. MODULE
SUPERVISES SUPPLY
VOLTAGE AND
DETECTOR LOOP.
(+)
(–)
TERMINAL WIRING MUST
BE POWER LIMITED.
TO NEXT
DEVICE
INTERFACE
MODULE SIGNAL LINE CIRCUIT
(SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
CONNECT MODULES TO
LISTED COMPATIBLE
CONTROL PANELS ONLY.
FROM
PANEL OR
PREVIOUS
DEVICE
3.9K EOL
RESISTOR
(INCLUDED)
A2143-10
DO NOT
LOOP WIRE UNDER TERMINALS. BREAK ALL WIRE RUN TO PROVIDE SUPERVISION OF CONNECTIONS. DETECTORS MUST
BE UL
LISTED COMPATIBLE WITH MODULE. INSTALL DETECTORS PER MANUFACTURER’S INSTALLATION INSTRUCTIONS
*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT
ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.
+
–
DO NOT MIX FIRE ALARM INITIATING, SUPERVISORY,
OR SECURITY DEVICES ON THE SAME MODULE.
C1061-00
FIGURE 4. INTERFACE TWO-WIRE CONVENTIONAL DETECTORS, NFPA CLASS A
(+)
(–)
(+)
(–)
(+)
(–)
(+)
(–)
LISTED
BATTERY-BACKUP
SWITCHED REGUALTED
DC POWER SUPPLY
POWER
TO THE INTERFACE
MODULE MUST
BE
EXTERNALL
Y SWITCED TO
RESET
THE DETECTORS. A
RELA
Y CONTROL MODULE CAN
BE USED
TO SWITCH POWER
FROM
A STANDARD POWER
SUPPL
Y (SEE FIGURE 5).
OPTIONAL BRANCH CIRCUIT
TO NEXT INTERFACE MODULE.
MODULE SUPERVISES SUPPLY
VOLTAGE AND
DETECTOR LOOP.
TERMINAL WIRING MUST
BE POWER LIMITED.
3.9K EOL RESISTOR
REQUIRED AT TERMINALS
8 & 9 (INCLUDED) A2143-10
DO NOT LOOP WIRE UNDER TERMINALS. BREAK ALL WIRE RUN TO PROVIDE SUPERVISION OF CONNECTIONS. DETECTORS
MUST BE UL LISTED COMPATIBLE WITH MODULE. INSTALL DETECTORS PER MANUFACTURER’S INSTALLATION INSTRUCTIONS
INTERFACE
MODULE
TO NEXT
DEVICE
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
CONNECT MODULES TO
LISTED COMPATIBLE
CONTROL PANELS ONLY.
FROM
PANEL OR
PREVIOUS
DEVICE
*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT
ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.
+
−
+
−
DO NOT MIX FIRE ALARM INITIATING, SUPERVISORY, OR SECURITY
DEVICES ON THE SAME MODULE.
C1062-00
FIGURE 5. RELAY CONTROL MODULE USED TO DISCONNECT A POWER SUPPLY
(+)
(–)
(+)
(–)
(+)
(–)
(+)
(–)
(+)
(–)
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
CONNECT MODULES TO LISTED COMPATIBLE
CONTROL PANELS ONLY.
FROM
PANEL OR
PREVIOUS
DEVICE
RELAY CONTROL
MODULE
TO NEXT
DEVICE
POWER LIMITED DC
POWER SUPPLY,
LISTED FOR FIRE
PROTECTION WITH
BATTERY BACKUP
*NOTE: ANY FAULT IN THE POWER SUPPLY IS
LIMITED TO THAT ZONE AND DOES NOT
RESULT IN A FAULT IN A SEPARATE ZONE.
C0945-00
2 I56-3552-006
©2022 Honeywell. 7/1/2022
Velociti®, Gamewell-FCI®, System Sensor®, and Honeywell® are registered trademarks of Honeywell International, Inc.