Honeywell Accenta Series Quick start guide

Engineer’s Manual
Honeywell Security
Accenta/Optima
0
123
456
789
Set
Reset
PA
Prog
Omit
Chime
Power D ay
8EP417A - Accenta LCD keypad
012 3 4
56 7 8 9
CHIME OMIT RESET PROG SET
1234 5678
ZONE
Accenta +
TA PA DAY POWER
PA
8EP416 - Accenta LED keypad
8EP396A Optima compact panel
with built-in LED keypad
Power
A ccenta
/!
mini
0123
5678
Chime Omit Reset
4
9
Set
Prog
PA
Attack
Tamper
Da
 ! " # $ % &
Zones

A ccenta
/!
mini
8SP399A - Accenta mini panel with
remote LCD keypad and communicator outputs.
 
8SP400A - Accenta mini panel with
remote LED keypad and communicator outputs
Gen "
ACCENTA
8SP419A - Accenta metal panel enclosure with
remote LCD keypad and communicator outputs
OR
8SP420A - Accenta metal panel enclosure with
remote LED keypad and communicator outputs

Accenta/Optima Engineer’s Manual Table of Contents
i
Contents
Introduction............................................................................................................ 1
Features.................................................................................................................. 1
Installation Design ................................................................................................ 2
Fixing the Control Panel ....................................................................................... 3
PCB .......................................................................................................................... 4
Wiring the System ................................................................................................. 4
Tamper Network ..................................................................................................... 4
Connecting Remote Keypads............................................................................... 5
Fitting the Remote Keypad ................................................................................... 6
Security Zones ....................................................................................................... 6
Fire Zone ................................................................................................................ 7
PA Circuit ................................................................................................................ 8
Extension Speaker ................................................................................................ 8
External Siren (Bell Box) Output .......................................................................... 9
13V Supply Output ............................................................................................................. 10
Set ........................................................................................................................................ 10
Remote Signalling Input and Outputs ............................................................... 11
Filtering of Intruder alarms ............................................................................................... 12
Factory Set Condition ......................................................................................... 13
Mains Connection ............................................................................................... 14
Testing the System .............................................................................................. 14
First Power Up...................................................................................................... 15
Engineer Program Mode ..................................................................................... 16
Indications on LED Keypads ............................................................................................ 16
System Indications .............................................................................................. 16
Entering/Exiting Engineer Program Mode ........................................................ 17
Defaulting Panel to Factory Settings ................................................................ 17
Defaulting User Code 1 and Engineer Code ..................................................... 17

Accenta/Optima Engineer’s Manual
Table of Contents
ii
Menu Options....................................................................................................... 18
0 = Walk Test ....................................................................................................................... 18
1 = Alarm Test ..................................................................................................................... 19
2 = Test Outputs ................................................................................................................. 20
3 = Set Up System Flags.................................................................................................... 21
4 = Set Up Time and Date .................................................................................................. 24
6 = Set Up Zone Names ..................................................................................................... 24
7 = Set Up Timers ...............................................................................................................25
8 = Set Up Codes ................................................................................................................28
C = View Event Log ............................................................................................................ 30
O = Omit Allow and Double Knock ................................................................................... 31
P = Set Up Programs .......................................................................................................... 34
Operating the System.......................................................................................... 42
Setting the System ............................................................................................................. 42
Resetting After an Alarm, Tamper or PA .......................................................................... 43
Unsetting the System ........................................................................................................ 43
Faults .................................................................................................................... 45
Specifications ...................................................................................................... 46
Appendix 1 - Event Log Messages .................................................................... 47
Appendix 2 - Library............................................................................................ 49
Servicing Organisation Details .......................................................................... 51
Parts ...................................................................................................................... 51

Accenta/Optima Engineer’s Manual
1
Introduction
This manual provides information on Installation design, panel fixing, wiring, power up and programming of the
intruder panels.
Features
8 zones programmable for Security, 2 zones for Fire.
PAinput.
Tamper input.
Outputs for External Siren (Bell) and Strobe.
4 Access level Codes, User 1, User 2, Engineer and Duress, all programmable.
3 fully selectable part set programs.
Chime on any security zone.
250 event memory (LCD Keypad), 8 event memory (LED keypad).
Programmable timers including bell cut off.
Walk Test facilities.
Quick set feature.
Supports up to four remote keypads with on board PA and illuminated keys positioned up to
100 meters from the panel.
Keypads can be wired in a star or daisy chain configuration from the panel.


Optima is supplied with a built in keypad.
Support of Prox set and unset with Simple Set keypad.
NVM for protection of engineer program and event log.
5 digital outputs for a wire-in digital communicator or dialler
(Not applicable for Optima compact panel).
Battery capacity of up to : 2.1Ah in Accenta/Optima mini enclosure,
7Ah inAccenta/Optima metal enclosure.
Features
4
2

Accenta/Optima Engineer’s Manual
2
Installation
Installation Design
The purchase of this alarm system represents a major step forward in the protection of the property and its
occupants. It is important to plan the installation before proceeding following the procedures and advice
contained in this manual.
Plan the position of each part of the alarm system and the cable runs. Detectors
should be sited with particular regard to the degree of coverage required.
All of the system wiring is connected directly to the panel. The Accenta panel may
be concealed inside a cupboard or loft space, but it must be installed within the
protected premises and in a position which is convenient for a mains supply. The
Optima panel may be installed near an entry/exit point.
The Remote Keypads (RKPs) should be mounted in positions which allows
ease of operation for the system users, typically within the entry/exit route
close to the final door and the master bedroom.
Additional internal sound speakers are recommended, these will provide high
volume alarm tones and low volume entry/exit tones. Speakers should
be positioned to provide good sound distribution throughout the building and so that
the exit tone is audible outside the main entry / exit door. This will enable the system
operator to check that the system is setting correctly.
The total current output of this control system (in alarm condition) is 1A when
supported by a fully charged battery. Calculate the total including the panel, remote
keypads, external siren with strobe light (also called a bell box) and detectors to
ensure that this rating is not exceeded.
Depending on which area you live, you may be required, by law to notify the
Local Authority and Police of the new security alarm installation. The local
authority requirements may differ from area to area, therefore, it is advisable to
contact local environmental officer to obtain full details of your area requirements.
0
123
456
789
Set
Reset
PA
Prog
Omit
Chime
Power Day
Accenta LCD keypad

Accenta/Optima Engineer’s Manual
3
Fixing the Control Panel
CAUTION:When positioning the control panel make sure that it is located in a dry place away
from damp areas.
NOTE: TheAccenta mini enclosure is illustrated here, however the procedures for the other panels is
similar.
Control Panel
Q
S
R
2. Disconnect the transformer wires from the board, these are
marked AC. Carefully remove the board by gently pushing
down the holding clips on the bottom edge of the board
and withdraw it from the base.
NOTE: When replacing the board align it on the round
support pillars to the bottom and allow it to
click down past the clips at the top of the case.
Refit the transformer wires into the terminal.
Q
RS
1. Remove the front cover(s) from the base assembly.
3. Fit the panel to the wall with suitable fixings. Ensure the
wall surface is flat to prevent base distortion. There are
cable entry holes provided in the rear of the base and
around the outside edges through the thinned out plastic
sections which may be cut away as required.
NOTE: The hole provided adjacent to the mains
transformer is a dedicated mains cable entry
hole.
 
 
 


 

  
  ! 
"#$%&'(
 
 
  
  


Figure 1. Removing the Front Cover
Figure 2. Removing the PCB
Figure 3. Fitting the Panel

Accenta/Optima Engineer’s Manual
4
PCB
There are four fuses mounted on the circuit board, all are 20mm anti-surge.
F1 1.6A - to protect the positive (+Ve) line of 12V battery
F2 1A - to protect the Speaker 13V supply
F3 1A - to protect the Siren (Bell) & Strobe supply
F4 1A - to protect the RKP 13V supply
As supplied, wire links are fitted across the PA and Tamper terminals to represent a closed circuit.
Wiring the System
CAUTION: Always power down the panel when wiring external circuits to prevent damage to
the panel electronics.
Systematically wire and test each circuit:
Zone, Tamper circuit and PAcircuits
Finish by wiring any additional extension speaker sounders, external siren (bell) / strobe and the 13V
supply.
Tamper Network
The Tamper circuit is used to protect all cables and detectors in the system from unauthorised access including
the panel and RKP covers.
The zone and PA tampers should be series wired and connected to the TAMP terminals. Terminals T andA
are for the external siren tamper. The TAMP terminals at the bottom left of the board are for the RKP
tampers.
Tamper alarms that occur in the Day mode operate internal sounders only. Tamper alarms in Set cause a full
alarm condition. Tamper is indicated on the control panel and RKPs.
Figure 4. PCB
PCB
-
STROBE
J6
+- AC
+TA
SCB
DB
BELL
+-
SET
1A
1A
1.6A
BELL/STROBE
BATTERY
BATT
J4
F1
F2
F3
J5
0V
TAMP
+13V
COMMS
SOUND
RV1
VOLUME
1A
RKP FUSE
F4
ABORT
J3
+13V 0V FIRE PA INT SET
0 1 2 3
5 6 7
CHIME OMIT RESET
9
SETPROG
Communicator is not fitted
to Optima compact panel Keypad and LEDs (except Power LED) are not
fitted to Accenta metal panels and Accenta mini panels
D1 D2 D3 D4 D5 D6 D7 D D9
D10
D22
D1
J2
PA
+
-
TAMP
+13V
0V
1234 5 67
13V
SPEAKER
4
TAMP

Accenta/Optima Engineer’s Manual
5
Figure 5. Connecting LED keypads to panel
Connecting Keypads
Connecting Remote Keypads
NOTE: Where an Accenta orAccenta mini panel is being installed, make sure there is at least one remote
keypad wired to the panel before the first power up.
Up to four remote Accenta LCD or LED keypads can be connected to the panel. Wire the keypad(s) as per
Figure 5 (LED keypad) or Figure 6 (LCD keypad).
NOTE: When the panel back-up battery is charging, the LCD keypad backlight may not operate.
Figure 6. Connecting LCD keypads to panel














 



!"#$# % $ & &'
#& ()  *







+13V 0V sound
TB1
comms
tamp tamp
TB2
Keypad PCB
+13V 0V sound
TB1
comms
tamp tamp
TB2
Keypad PCB







 

Board
Panel

Accenta/Optima Engineer’s Manual
6
Security Zones
It is recommended that no more than 10 magnetic contacts are connected to the same zone and that the
combined cable length for each zone does not exceed 100 metres.
Figure 7. Security Zone Wiring
Fitting the Remote Keypad
1 Separate the RKP baseplate from the main assembly by slackening the retaining screw.
2 Cut away the required thin wall sections around the edges of the baseplate for cable entry.
3 The baseplate mounting holes are 60 mm centres (LED keypad) or 75 mm (LCD keypad) which allow
it to be fixed to a single gang electrical metal box. As an alternative, the baseplate may be fitted directly to the
wall using screws and wall plugs. If these are not appropriate for the wall then use suitable alternative fixings.
CAUTION: The PCB board must not be removed from the front moulding and doing so may
invalidate the warranty.
4 Bring the cables into the baseplate and wire to the terminal block on the baseplate.
5 Refit the RKP main assembly to the baseplate by locating the top retaining clips into the inside top part
of the baseplate. Close the main assembly onto the baseplate, ensuring that the wiring does not foul the tamper
switch/spring or the PCB support pillars. Resecure the screw in the bottom of the case.
Remote Keypad




  











  !