Honeywell L5200 Series Operating instructions

LYNX Touch
L5200/L7000 Series
Security System
Programming Guide
800-16086V1 12/14 Rev. A L5200CN/L7000CN

- 2 -
Table of Contents
Entering Programming Mode ....................................................................................................................................3
Programming the Data Fields ...................................................................................................................................3
Loading a Default Set................................................................................................................................................3
Exiting Programming Mode.......................................................................................................................................3
Data Fields ................................................................................................................................................................4
Change Installer Code ...........................................................................................................................................4
Program System Type ...........................................................................................................................................4
Program Date and Time.........................................................................................................................................5
Program Communications .....................................................................................................................................6
Program Zones ......................................................................................................................................................7
Program Keys ........................................................................................................................................................9
Program Reporter ..................................................................................................................................................9
Program Sounder.................................................................................................................................................15
Program System Settings ....................................................................................................................................16
Program the Z-Wave Module...............................................................................................................................17
Communication Diagnostics ................................................................................................................................18
Zone Programming Worksheet ...............................................................................................................................20
Explanation of Zone Assignment Table Headings ...............................................................................................22
5800 Series Transmitter Loop Numbers Diagram...................................................................................................23
LYNX Touch L5200CN Programming Default Values.............................................................................................24
LYNX Touch L7000CN Programming Default Values.............................................................................................27
LYNX Touch Series Summary of Connections Diagram ........................................................................................31
Refer to the LYNX Touch Series Installation and Setup Guide P/N 800-16082 or later for detailed
information on programming the system. The Installation and Setup Guide contains full descriptions
for all data fields.
UL
LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour backup
battery (P/N LYNXRCHKIT-SHA) is installed.

- 3 -
Entering Programming Mode
You may find it convenient to adjust the volume setting before entering the Programming Mode. This
will allow you to clearly hear feedback announcements or system beeps.
1. Power-up the control and allow it to “boot-up”. “System Standby” is displayed on the touch screen. When the
“boot-up” is complete (approximately 1-2 minutes) “Ready to Arm” is displayed.
2. Select the “Security” icon.
3. Select the “More” tab on the first page of the Security Screen.
4. Select “Tools” icon.
5. Enter the Installer Code (4 + 1 + 1 + 2) on the displayed keypad.
5. The Installer Tools menu screen appears. Select the “Program” button. “System Programming…” is displayed
and on the L5200CN, the “Armed” and “Ready” LEDs (L5200CN) flash. On the L7000CN the “Panic” button is
lit and the “Home” button alternately flashes red and green.
6. Select one of the following options to advance to that Programming screen:
Installer Code
Date Time
Zones
Keys
System Type
Communicator
Comm. Diagnostics
Reporter
Use the down arrow to scroll to the next page of options.
Sounder
Default Config.
Reset Master Code
System Settings
Language
Z-Wave
5. Select an option to advance to that Programming screen.
Note: If a different Installer Code has been programmed, enter: the New Installer Code.
Programming the Data Fields
1. Select each desired programming option, and then select the required entry. The system beeps each time a
selection is made.
2. The system will toggle or scroll through the options or display a new screen as applicable for the specific
option.
3. To delete or change an entry, simply select the desired option, and then select the required entry.
Loading a Default Set:
1. Enter the Installer Programming Mode and advance to second page of the System Programming.
2. Select ‘Default Config’ and select the appropriate Default Configuration from the following options or Select
Default Downloader to reset all subscriber account numbers and CSID in preparation for an initial download:
Default Config 1
Default Config 2
Default Config 3
Default Config 4
Default Downloader
Note: Refer to the Programming Default Values section of this manual to view the default values.
Exiting Programming Mode:
1. Select the “” key to exit the current screen. The system returns to the previous screen.
2. Select the “” key as required until system displays a Confirmation screen.
3. Select “Yes” to allow the installer to re-enter Programming mode or “No” to prevent re-entry.
4. Select the “” key again to return to the Security Screen OR depress the Home button to return to the Home
Screen.

Screen Display Function & Programming Options
- 4 -
DATA FIELDS
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen display.
Change Installer Code
5000-100-129-V0
Installer Code
Installer Code
Enter 4 digits [The defaulted Installer Code 4112 is displayed on the left side of the screeen]
0-9
Program System Type
RF Jam
Disabled
RF Jam
Disabled
RF Jam Log
RF Jam Log & Report
Speaker Phone
Disabled
Note: The Speaker Phone feature is not available on the LYNX Touch L7000CN.
Speaker Phone
Disabled
Enabled
Two Way Voice
Disabled
Two-Way Voice
Disabled
Enabled
RF House Code
0
RF House Code
Enter 2 digits, 00-31
Remote Phone
Enabled
Note: The Remote Phone feature is not available on the LYNX Touch L7000CN.
Remote Phone
Disabled
Enabled
Phone Notification
Disabled
Note: The Remote Phone feature is not available on the LYNX Touch L7000CN.
Phone Notification
Disabled
Keypad
Trouble
Note: If “Keypad” or “Trouble” is selected you will be prompted to program a phone detect time.
Phone Detect Time
2 Minutes
Note: The Remote Phone feature is not available on the LYNX Touch L7000CN.
Phone Detect Time
1 Minute
2 Minutes
3 Minutes
4 Minutes
Events - Log All
Log All Set
Events – Log All
Note: If Press to Log All is selected the system will log the following events:
Alarm
Bypass
Open/Close
Trouble
Non-Security
Events – Log Alarm
Enabled
Events – Log Alarm
Enabled
Disabled
Events – Log Bypass
Enabled
Events – Log Bypass
Enabled
Disabled
Events – Log Open Close
Enabled
Events - Log Open/Close
Enabled
Disabled
Events – Log Trouble
Enabled
Events – Log Trouble
Enabled
Disabled

Screen Display Function & Programming Options
- 5 -
Non Security
Disabled
Non Security
Enabled
Disabled
Remote Access Serial
Disabled
Remote Access Serial
Enabled
Disabled
Note: If the “Remote Access Serial” option is enabled, you will be prompted to select a “Multi Mode
Serial”.
Multi Mode Serial
Disabled
Multi Mode Serial
Enhanced Reports
Disabled
Program Date and Time
5000-100-131-V0
Date Time
Date Time
Note: If you are installing a 4GLC or 3 GLC, L5100-WiFi or ILP5 Communication Module, the time and
date will be programmed and updated automatically via Central Station. You must still program
the correct Time Zone below.
1. Month and Year
2. Select the correct date
3. Enter the correct time
4. Select AM or PM
5. Select Save or continue below.
Time Zone
Eastern (EST)
Time Zone
Eastern (EST) Pacific (PST) Atlantic (AST)
Central (CST) Alaska (AKST) Newfoundland (NT)
Hawaii (HAST) Brasilia (BRT)
Mountain (MST) Mid-Atlantic (MAT)
Day Light Savings Time
Yes
Day Light Savings Time
Yes
No
Note: If Yes is selected, the following options will be active.
Start Month
March
Start Month
January July
February August
March September
April October
May November
June December
Start Week
Second
Start Week
First
Second
Third
Fourth
Last
Next to Last
3rd from Last
End Month
November
End Month
January July
February August
March September
April October
May November
June December

Screen Display Function & Programming Options
- 6 -
End Week
First
Start Week
First
Second
Third
Fourth
Last
Next to Last
3rd from Last
Program Communications
5000-100-132-V0
Communicator
Communicator
Program the following options:
Communications Path APL
City ID CS ID Sub ID
Supervision Old Alarm Time
Remote Acc. Comm. Multi Mode Comm.
GSM Fault Time OR
IP Fault Time
Communications Path
None
Communications Path
None
IP
GSM
WiFi
WiFi & GSM
APL
Disabled
Advanced Protection Logic
Enabled
Disabled
City ID
Primary City Identification
Enter 2 digits
01-99
CS ID
Primary Central Station Identification
Enter 2-digits (HEX)
01-FE
Sub ID
Primary Subscriber Identification
Enter 4-digits
0001-9999
Supervision
24 Hours
Supervision
24 Hours
None
30 Days
Old Alarm Time
10 Minutes
Old Alarm Time
10 Minutes 15 Minutes
30 Minutes 1 Hour
2 Hours 4 Hours
8 Hours 12 Hours
24 Hours
Remote Acc. Comm.
Disabled
Remote Access Communication
Disabled
Enabled
Note: If enabled the following option will be active.
Multi Mode Comm.
Disabled
Multi Mode Communication
Disabled
Relay Reports
Enhanced Reports
GSM Fault Time (min)
00
GSM Fault Time (min) (displayed if GSM is selected as Communications Path)
Enter 2-digits
00-99

Screen Display Function & Programming Options
- 7 -
IP Fault Time (min)
00
IP Fault Time (min) (displayed if IP or WiFi is selected as Communications Path)
Enter 2-digits
00-99
Use DHCP
Yes
Use DHCP .
Yes
No
Note: If No is selected the following options will be active
NIC IP Address
255.255.255.255
NIC IP Address (Appears only if “no” was selected in the “Use DHCP Field”)
Enter 4 part address
Subnet Mask
255.255.255.255
Subnet Mask (Appears only if “no” was selected in the “Use DHCP Field”)
Enter 4 part address
Gateway IP Address
255.255.255.255
Gateway IP Address (Appears only if “no” was selected in the “Use DHCP Field”)
Enter 4 part address
DNS Server IP Address
255.255.255.255
DNS Server Address (Appears only if “no” was selected in the “Use DHCP Field”)
Enter 4 part address
GSM Rollover
No
GSM Rollover (Appears only if “WiFi and GSM” was selected in the “Communications Path”
field)
Yes
No
GSM 24 Hour Test
No
GSM 24 Hour Test (Appears only if “WiFi and GSM” was selected in the “Communications
Path” field)
Yes
No
Program Zones
5000-100-133-V0
Zones
Zones
Select from the following zone options:
1. New
2. Front Door
3. Back Door
4. Window
5. Motion Sensor
6. New
7. – 45. New
46. – 48. New (Main)* Garage
Zones 46 to 48 are reserved for Garage Door Zones (L5200)
45. – 48. New (Main)* Garage
Zones 45 to 48 are reserved for Garage Door Zones (L7000)
49. – 64. New
Zones 48 to 64 (L5200)
49. – 80. New
Zones 49 to 80 (L7000)
140. – 147. 4 Button
Zones 140 to 147 (L5200 and L7000)
148. – 155. New (Button Zones)
Zones 148 to 155 (L5200 Only)
180. – 185. Temperature
Z-Wave Thermostat zones (L5200)
180. – 187. Temperature
Z-Wave Thermostat zones (L7000)
95. Fire
96. Medical
99. Police
Select a zone and then select “Edit” or “Add New” to program the next available zone.
Program the following options:(dependent upon Zone Type):
Serial Number Loop Number
Zone Description 1 Zone Description 2
Device Type Response Type
Report Chime Supervision

Screen Display Function & Programming Options
- 8 -
Serial Number
Serial Number
When “Serial Number” has been selected “Enter Serial Number or Activate” is displayed.
The transmitter serial number and loop number can be enrolled via RF transmission OR
manually.
Enroll via RF Learning To enroll the device using RF Learning mode three transmissions
(open/close) of the device will be required. The initial transmission activates the RF
Learning mode and the system will emit a single beep. A second transmission enrolls the
serial number and the system beeps two times and displays “Activate Sensor Again To
Confirm”. A third transmission will confirm the serial number. The system beeps two times
and returns to the Zone programming Screen.
Enroll Manually
Enter the 7-digit serial number printed on the transmitter using the displayed keypad and
select “Done”. The system beeps one time and returns to the Zone programming Screen.
Loop Number
1
Loop Number
1, 2, 3 or 4
Zone Description 1
Zone Description 2
Zone Description 1
The system announces the Zone Description. If desired, enter a zone descriptor.
Zone Description 2
The system announces the Zone Description. If desired, enter a zone descriptor.
Device Type
Device Type
Choose from the following options (dependant upon the Device Type):
New Door
Window Motion Sensor
Glass Break Smoke Detector
Heat Sensor Carbon Mono. Det.
Temperature Flood
Environmental Medical
Fire Police
Garage Door Other
Response Type
Not Used
Response Type Choose from the following options (dependant upon the Zone):
Not Used Arm Stay Fire No Verification
Entry Exit 1 Disarm Monitor
Entry Exit 2 Silent Burglary Garage
Interior Follower Resident Response Arm Away
24 Hour Silent General Response No Response
24 Hour Auxiliary Perimeter Resident Monitor
Interior With Delay Day/Night General Monitor
Carbon Monoxide 24 Hour Audible Fire With Verification
Garage Monitor Trouble
Report
Yes
Report
Yes
No
Chime
Disabled
Chime
Disabled Ascend Doorbell 1
Standard Ascend Long Doorbell 2
Melody Alert 1 Evolve
Melody Long Alert 2
Supervision
Supervised
Supervision
Hardwire Zone
Normal Open
Normal Closed
End of Line
RF Zone
Supervised
Unsupervised
Temperature
High Temp
Low Temp
Arm Night
No
Arm Night (Only available if “Motion Sensor” is selected in the “Response Type” field.
Yes
No

Screen Display Function & Programming Options
- 9 -
Program Keys
Keys
Keys
Select from the following options:
Edit Add New Delete
If add new is selected the following options can be programmed:
Key Type User
Serial Number Zone
Button Key 1 – Zn 140 Button Key 2 – Zn 141
Button Key 3 – Zn 142 Button Key 4 – Zn 143
Button Key 5 – Zn 144 Button Key 6 – Zn 145
Button Key 7 – Zn 146 Button Key 8 – Zn 147
Key Type
4 Button Key
Key Type
1 Button Key.
2 Button Key
4 Button Key
6 Button Key
8 Button Key
User
User
Master
Duress
Guest
User 3 through User 30 (L5200CN)
User 3 through User 46 (L7000CN)
Note: The Key must be associated with a specific User/User Code in order for it to operate. Refer to the
LYNX Touch User Guide for additional Information regarding User Codes.
Serial Number
0
Serial Number
When “Serial Number” has been selected “Enter Serial Number or Activate” is displayed.
The transmitter serial number and loop number can be enrolled via RF transmission OR
manually.
Enroll via RF Learning To enroll the device using RF Learning mode three transmissions
(open/close) of the device will be required. The initial transmission activates the RF
Learning mode. A second transmission enrolls the serial number and the system beeps two
times and displays “Activate Sensor Again To Confirm”. A third transmission will confirm the
serial number. The system beeps two times and returns to the Zone programming Screen.
Enroll Manually
Enter the 7-digit serial number printed on the transmitter using the displayed keypad and
select “Done”. The system beeps one time and returns to the Zone programming Screen
Zone
140
Zone
Manually enter a specific two-digit Zone Number (140-155 L5200 OR 140-163 L7000).
Button Key * - Zone *
Button Key * Zn *
Enter a function for each button key from the following options:
Disarm Arm Away
Arm Stay No Response
24 Hour Silent 24 Hour Audible
24 Hour Auxiliary Silent Burglary
Fire No Verification
* Options are the same for each Button/Zone combination.
Program Reporter
Reporter
Reporter
Note: The Follow Me Phone features are not available on the LYNX Touch L7000CN.
Program the following options:
Primary CS Info Secondary CS Info
Follow Me Phone 1 Follow Me Phone 2
Report Selection Options
Downloader
Primary CS Info
Primary Central Station Information
Phone Type
Communicator Type

Screen Display Function & Programming Options
- 10 -
Phone Type
Contact Id: 4 Digit
Phone Type
None
Contact Id : 4 Digit
Contact Id : 10 Digit
SIA
Note: If SIA, Contact Id: 4 Digit, or Contact Id: 10 Digit is selected the Phone Number and Account
Number options will be displayed.
Communicator Type
None
Communicator Type
None
GSM
WiFi
WiFi & GSM
IP
Note: If IP is selected the Dynamic Priority option will be displayed.
Phone Number
Phone Number
Enter the Primary Central Station Phone Number (Up to 20 digits)
Account Number
FFFF
Account Number
Enter the Primary Central Station Account Number
Dynamic Priority
Dynamic Priority
Redundant Reports
Preferred Telco
Preferred Radio
Note: If Preferred Telco or Preferred Radio is selected the Dynamic Delay option will be displayed.
Dynamic Delay
Dynamic Delay
15 Seconds
30 Seconds
60 Seconds
90 Seconds
Report All
Press to Report All
Report All
Press to Report All
Report All Set
Report Alarms
Enabled
Report Alarms
Disabled
Enabled
Report Troubles
Enabled
Report Troubles
Disabled
Enabled
Report Open/Close
Disabled
Report Open/Close
Disabled
Enabled
Report Tests
Enabled
Report Tests
Disabled
Enabled
Secondary CS Info
Secondary Central Station Information
Phone Type
Communicator Type
Phone Type
None
Phone Type
None
Contact Id: 4 Digit
Contact Id: 10 Digit
SIA
Note: If SIA, Contact Id: 4 Digit or Contact Id: 10 Digit is selected, the Phone Number and Account
Number options will be displayed.

Screen Display Function & Programming Options
- 11 -
Communicator Type
None
Communicator Type
None
GSM
WiFi
WiFi & GSM
IP
Note: If IP is selected the Dynamic Priority option will be displayed.
Phone Number
Phone Number
Enter the Secondary Central Station Phone Number (Up to 20 digits)
Communicator Type
None
Communicator Type
None
GSM
IP
Note: If IP is selected the Dynamic Priority option will be displayed.
Phone Number
Phone Number
Enter the Secondary Central Station Phone Number
Account Number
FFFF
Account Number
Enter the Secondary Central Station Account Number
Dynamic Priority
None
Dynamic Priority
Redundant Reports
Preferred Telco
Preferred Radio
Note: If Preferred Telco or Preferred Radio is selected the Dynamic Delay option will be displayed.
Dynamic Delay
None
Dynamic Delay
None
15 Seconds
30 Seconds
60 Seconds
90 Seconds
Report All
Press to Report All
Report All
Press to Report All
Report All Set
Report Alarms
Enabled
Report Alarms
Disabled
Enabled
Report Troubles
Disabled
Report Troubles
Disabled
Enabled
Report Open/Close
Disabled
Report Open/Close
Disabled
Enabled
Report Tests
Enabled
Report Tests
Disabled
Enabled
Follow Me Phone 1
Follow Me Phone 1 (This feature is not available on the LYNX Touch L7000CN)
Choose from the following options:
Phone Type Phone Number
Report All Report Alarms
Report Troubles Report Open/Close
Report Tests

Screen Display Function & Programming Options
- 12 -
Phone Type
None
Phone Type (This feature is not available on the LYNX Touch L7000CN)
None
Follow me
Phone Type
None
Phone Number (This feature is not available on the LYNX Touch L7000CN)
Enter the Follow Me Phone Number
Report All
Press to Report All
Report All (This feature is not available on the LYNX Touch L7000CN)
Press to Report All
Report All Set
Report Alarms
Disabled
Report Alarms (This feature is not available on the LYNX Touch L7000CN)
Disabled
Enabled
Report Troubles
Disabled
Report Troubles (This feature is not available on the LYNX Touch L7000CN)
Disabled
Enabled
Report Open/Close
Disabled
Report Open/Close (This feature is not available on the LYNX Touch L7000CN)
Disabled
Enabled
Report Tests
Disabled
Report Tests (This feature is not available on the LYNX Touch L7000CN)
Disabled
Enabled
Follow Me Phone 2
Follow Me Phone 2 (This feature is not available on the LYNX Touch L7000CN)
Choose from the following options:
Phone Type Phone Number
Report All Report Alarms
Report Troubles Report Open/Close
Report Tests
Phone Type
None
Phone Type (This feature is not available on the LYNX Touch L7000CN)
None
Follow me
Phone Number
Phone Number (This feature is not available on the LYNX Touch L7000CN)
Enter the Follow Me Phone Number
Report All
Press to Report All
Report All (This feature is not available on the LYNX Touch L7000CN)
Press to Report All
Report All Set
Report Alarms
Disabled
Report Alarms (This feature is not available on the LYNX Touch L7000CN)
Disabled
Enabled
Report Troubles
Disabled
Report Troubles (This feature is not available on the LYNX Touch L7000CN)
Disabled
Enabled
Report Open/Close
Disabled
Report Open/Close (This feature is not available on the LYNX Touch L7000CN)
Disabled
Enabled
Report Tests
Disabled
Report Tests (This feature is not available on the LYNX Touch L7000CN)
Disabled
Enabled

Screen Display Function & Programming Options
- 13 -
Report Selection
Report Selection
Choose from the following options:
Arm Away Arm Stay Bypass Bypass Restore
Disarm Exit Error AC Loss AC Loss Restore
Recent Closing Event Log Full Low Battery Low Battery Restore
Trouble Trouble Restore RF Low Battery RF Low Battery Restore
Alarm Restore Alarm Cancel
Test Test Restore
Arm Away
Enabled
Arm Away
Disabled
Enabled
Arm Stay
Enabled
Arm Stay
Disabled
Enabled
Disarm
Enabled
Disarm
Disabled
Enabled
Exit Error
Enabled
Exit Error
Disabled
Enabled
Recent Closing
Enabled
Recent Closing
Disabled
Enabled
Event Log Full
Enabled
Event Log Full
Disabled
Enabled
Trouble
Enabled
Trouble
Disabled
Enabled
Trouble Restore
Enabled
Trouble Restore
Disabled
Enabled
Alarm Restore
Enabled
Alarm Restore
Disabled
Enabled
Alarm Cancel
Enabled
Alarm Cancel
Disabled
Enabled
Test
Enabled
Test
Disabled
Enabled
Test Restore
Enabled
Test Restore
Disabled
Enabled
Bypass
Enabled
Bypass
Disabled
Enabled
Bypass Restore
Enabled
Bypass Restore
Disabled
Enabled
AC Loss
Enabled
AC Loss
Disabled
Enabled
AC Loss Restore
Enabled
AC loss Restore
Disabled
Enabled
Low Battery
Low Battery Restore
Disabled

Screen Display Function & Programming Options
- 14 -
Enabled
Enabled
Low Battery Restore
Enabled
Low Battery Restore
Disabled
Enabled
RF Low Battery
Enabled
RF Low Battery
Disabled
Enabled
RF Low Battery Restore
Enabled
RF Low Battery Restore
Disabled
Enabled
Options
Options
Choose from the following options:
PBX Call Wait Cancel
Number of Reports Alarm Report Delay
First Report Offset Report Frequency
PBX
PBX (This feature is not available on the LYNX Touch L7000CN)
Enter PBX Prefix
Call Wait Cancel
Call Wait Cancel
Enter Call Wait Cancel Prefix
Number of Reports
Unlimited
Number of Reports
Unlimited
10 Reports
Alarm Report Delay
No Delay
Alarm Report Delay
No Delay
15 Sec.
30 Sec.
45 Sec.
First Report Offset
6 Hrs
First Report Offset
6 Hrs
12 Hrs
18 Hrs
24 Hrs
Report Frequency
Never
Report Frequency
Never
Every Day
Every 7 Days
Every 30 Days
Downloader
Downloader
Choose from the following options:
Phone Answer Modem Speed
Ans. Machine Defeat Callback Number
Ring Counter Flexible Callback
Number
Phone Answer
Yes
Phone Answer (This feature is not available on the LYNX Touch L7000CN)
Yes
No
Modem Speed
Slow
Modem Speed (This feature is not available on the LYNX Touch L7000CN)
(Future Use)
Ans. Machine Defeat
Yes
Answering Machine Defeat (This feature is not available on the LYNX Touch L7000CN)
Yes
No
(If No is selected the Ring Counter Option will be displayed.)
Ring Counter
2
Ring Counter (displayed if Ans. Machine Defeat is set to “No”)
Enter ring counter (1-14)

Screen Display Function & Programming Options
- 15 -
Callback Number
Yes
Callback Number
Enter a Callback Number
Flexible Callback
No
Flexible Callback
Yes
No
(If Yes is selected the Number Option will be displayed.)
Number
Number (displayed if Flexible Callback is set to “Yes”)
Enter the number of flexible callbacks that will be used (1-3)
Program Sounder
Sounder
Sounder
Choose from the following options:
Burglary Alarm Sound Burglary Bell Timeout
Fire Bell Timeout Arm Confirm
Burglary Alarm Sound
Yes
Burglary Alarm Sound
Yes (Full volume)
No (Test volume – installer mode)
Burglary Bell Timeout
4 Minutes
Burglary Bell Timeout
No
4 Minutes
8 Minutes
12 Minutes
16 Minutes
Fire Bell Timeout
4 Minutes
Fire Bell Timeout
No
4 Minutes
8 Minutes
12 Minutes
16 Minutes
Arm Confirm
RF Keyfob
Arm Confirm
None
All RF
RF Key Fob
RF Keypad
Alarm Options
Unlimited
Alarm Options
Unlimited
1
2
10

Screen Display Function & Programming Options
- 16 -
Program System Settings
System Settings
System Settings
Choose from the following options:
Entry Delay 1 Entry Delay 1
Exit Delay Backlight Timeout
Quick Arm Quick Exit Restart Exit Time
Force Bypass Exit Warning Auto Stay Arming
Lack of Usage Notify Power-up in Previous
Display Alarm Cancel Display Exit Time
Cross Zone Delay
Cross Zone 1 Cross Zone 2
Entry Delay 1
30 Seconds
Entry Delay 1
None
15 Seconds
30 Seconds
45 Seconds
60Seconds
90 Seconds
2 Minutes
Entry Delay 2
60 Seconds
Entry Delay 2
None
15 Seconds
30 Seconds
45 Seconds
60Secon
ds
90 Seconds
2 Minutes
Exit Delay
60 Seconds
Exit Delay
None
15 Seconds
30 Seconds
45 Seconds
60Seconds
90 Seconds
2 Minutes
Backlight Timeout
No
Backlight Timeout
No
30 Seconds
Quick Arm
Yes
Quick Arm
Yes
No
Quick Exit
No
Quick Exit
Yes
No
Restart Exit Time
No
Restart Exit Time
Yes
No
Force Bypass
No
Force Bypass
Yes
No
Exit Warning
Yes
Exit Warning
Yes
No
Auto Stay Arming
No
Auto Stay Arming
Yes
No

Screen Display Function & Programming Options
- 17 -
Lack of Usage Notify
Disabled
Lack of Usage Notify
Disabled
1 Day
7 Days
27 Days
90 Days
180 Days
365 Days
Power-Up in Previous
Yes
Power-Up in Previous State
Yes
No
Display Alarm Cancel
No
Display Alarm Cancel
Yes
No
Display Exit Time
Yes
Display Exit Time
Yes
No
Cross Zone Delay
3 Minutes
Cross Zone Delay
None
30 Seconds
1 Minute
90 Seconds
2 Minutes
3 Minutes
4 Minutes
Cross Zone 1
Disabled
Cross Zone 1
Disabled
Cross Zone 2
Disabled
Cross Zone 2
Disabled
Program the Z-Wave Module
5100-100-067-V0
Z - Wave
Z-Wave
Note: This procedure must be completed any time that the panel has been defaulted or
updated.
Z-Wave
Enabled-Installed Telephone
Z-Wave
Select from the following options:
Enabled – Installed Telephone Side
Disabled
Temperature Display
Fahrenheit
Temperature Display
Select from the following options:
Fahrenheit
Celsius

- 18 -
Communications Diagnostics
Note: For additional information regarding these fields, refer to the LYNX Touch Installation and Setup Guide P/N 800-16082 or
higher.
Comm. Diagnostics
Communication Diagnostics
Choose from the following options (depending upon the Communication Module that is
installed:
Communication
Status
Ethernet
Information
GSM
Information
Communication
ID Numbers
Test
Communication
Setup
Communication
WiFi Location WiFi Status Configure
WiFi
Communication Status - Provides a status of the IP or Cellular communications paths and performs a self-test of the
advanced encryption standard (AES) algorithm.
Message Function
GSM OR IP: Displays Network Connectivity status
Encryption: Displays result of encryption test (Pass or Fail)
AlarmNet Registration: Displays Account Registration status
Ethernet Information - Displays IP information if the IP Communication Path is enabled.
Message Function
Physical Link: Confirms physical link connection and speed
DHCP: Displays status of server
NIC IP Address: Displays the communication device’s assigned IP address
Subnet Mask: Displays the 32-bit address mask used to indicate the portion (bits) of the
IP address that is being used for the subnet address
Gateway IP Address: Displays the IP address assigned to the Gateway
DNS Server IP Address: Displays the IP address assigned to the DNS server
GSM Information - Displays GSM information if the GSM communication path is enabled and the device is registered.
Message Function
Cell Registration: Displays registration status
Primary RSSI: Displays primary site RSSI signal strength (1 to 5 stars)
GPRS:
(2G only, always available in 3G/4G) Displays availability of GPRS service.
Country: Displays country code
Network: Displays network code
LAC: Displays local area code
Cell: Displays base station ID (4-digit in 2G or 6-digit in 3G/4G)
Base Station: (2G only) Displays Base Station Antenna Sector
Pri Sync Code: (3G/4G only) Displays primary sync code
Channel: Displays control in use
Second Site RSSI: Displays presence of Secondary site RSSI level availability
If the GSM is not registered the following may be displayed:
Searching for Coverage! Searching for cell network
SIM Error! No SIM card present of SIM card faulty
Cell Registration: SIM Not Active SIM is not activated
Cell Registration: Not Registered Not registered with the cell network
Communication ID Numbers- Displays programmed SIM card information for the installed communication module.
Message Function
MAC: Displays MAC address
MAC CRC: Displays MAC CRC number
SCID: Displays SIM card identification number
IMEI: Displays communication module identity number
WiFi* Displays physical address of the WiFi module
WiFi Ver* Displays WiFi Module software version
* If applicable

- 19 -
Communications Diagnostics
Test Communication - Performs network diagnostics and sends test alarms to the network. The following tests are
available depending on the type of communications module installed.
Message Function
Send Cellular Message: Available if Cellular communication path is enabled
Test Ethernet: Available if IP or WiFi communication path is enabled
Send Ethernet Message: Available if IP or WiFi communication path is enabled
Send Any: Available if IP or WiFi and Cellular communication path is enabled
Setup Communication – Registers the LYNX Touch and its associated communication module, update configuration files
or reset factory defaults.
Selection Function
Download Config File: The device configuration file will be downloaded
Update Server: The communication device uploads its configuration to the server
Factory Defaults: The communication device is reset to factory default values
WiFi Stats – Displays WiFi Specific Diagnostics information (Not intended for Installer use)

- 20 -
Zone Programming Worksheet
Fill in the required data on this worksheet, then follow the programming procedure. (The defaults shown are for
Configuration 1)
See Explanation of Zone Assignment Table Headings
Note: Zones 65-70, 156-163, and 186-187 are only available on the LYNX Touch L7000CN control.
Zone
No.
Loop
No.
Device
Type Response Type Alarm Report
Chime Supervision Arm
Night
Transmitter
Serial Number
Zone
Descriptor
1 N/A New Not Used Yes Disabled End of Line N/A N/A (HW Zone)
2 2 Door Entry Exit 1 Yes Standard Supervised N/A Front
3 2 Door Entry Exit 1 Yes Standard Supervised N/A Back
4 2 Window Perimeter Yes Standard Supervised N/A N/A
5 1 Motion Sensor Interior with Delay Yes Disabled Supervised No N/A
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42