Honeywell CommerCialPro 7000 Operation manual

PRODUCT DATA
® U.S. Registered Trademark
Copyright © 1998 Honeywell Inc. • All Rights Reserved
Honeywell 7000 Solid State Alarm System
APPLICATION
The Honeywell 7000 is a solid state fire/burglary and home
health care alarm system designed to protect a wide range of
private residences. This UL-listed system is easily
expandable and can be customized to meet the demanding
needs of homeowners.
FEATURES
•Can display up to 96 points of protection.
•Eight hardwire zones built into the control panel.
•Optional RF and hardwired expansion on Hbus.
•Supports keypads with custom text displays.
•Mode-based operation for simple error-free control.
•Date and time stamped event log.
•Up to 24 fully programmable outputs.
Contents
Application .......................................................................... 1
Features .............................................................................. 1
Specifications ...................................................................... 2
Ordering Information ........................................................... 2
Installation ........................................................................... 3
Programming....................................................................... 19
Operation ............................................................................ 21
Checkout ............................................................................. 24
Troubleshooting .................................................................. 25
Regulatory Agency Statements ........................................... 26
69-1192-1

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1 2
ORDERING INFORMATION
When purchasing replacement and modernization products refer to the price sheets for complete ordering number.
If you have additional questions, need further information, or would like to comment on our products or services, please write or
phone:
1. Your local Home and Building Control Sales Office (check white pages of your phone directory).
2. Home and Building Control Customer Relations
Honeywell, 1885 Douglas Drive North
Minneapolis, Minnesota 55422-4386
In Canada—Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.
International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,
Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.
SPECIFICATIONS
System 7000 Specifications
Electrical Ratings:
System Power:
115 Vac; 60 Hz, 0.5A.
Low voltage Input to Control Panel
24 Vac , 2A (50 VA, UL-listed, fused Class II Transformer)
NOTE: 24 AC Power wiring is limited to 20 feet of
No. 18 AWG wire.
Outputs:
No. 1 (Bell/Horn):
1A maximum at 13.8 Vdc.
No. 2 (AUX):
100 mA maximum at 13.8 Vdc.
Fusing:
Hbus: +13.8 Vdc, current limited at 2A.
AUX Horn: +13.8 Vdc, current limited at 2A.
Battery Charging Output:
800 mA maximum at 13.8 Vdc.
Power Consumption (at 13.8 Vdc):
Keypad 120 mA.
Point Expansion Module (PEM), 60 mA (120 mA when
both relays are on).
RF Expansion Module (RFEM), 60 mA.
Ademco Receiver, 50 mA.
Ademco Transmitters (see individual Ademco specification
sheet with each type of transmitter).
Battery Backup:
7AH Minimum, 28 AH Maximum at 12 to 13.8 Vdc.
Fuses:
One 2A, AGA2 fuse: F3 = AC.
Digital Communicator (Located on Control Panel)
Format: Modem 2E.
Line Seizure: Double Pole.
Ringer Equivalence: 1.0 B.
FCC Registration No.: B7FUSA-30171-AL-E.
Connection: RJ31X Type.
Circuit wiring:
Fire Circuit (Loop 8):
1000 feet, No. 18 AWG wire, 50 mA maximum,
for 10 two-wire smoke detectors.
Burglary circuits (Loop 1-7):
1000 feet maximum, No. 22 AWG wire.
End of Line Resistors (EOLR):
Inputs 1 through 7: 3.3 kilohm.
Input 8: 5.1 kilohm.
Four Wire HBus Interface (Cable No. 10-6608, 22 AWG)
Red: Power 13.8 VDC 1.0 amps maximum load.
Black: ground.
Yellow: (+) Data high.
Green: (-) Data low.
120 Ohm 5% 1/4 Watt end-of-line (EOL) resistor at end
of last bus device.
250 feet home run 22 AWG, 500 feet home run
18 AWG.
Environmental Ratings:
Ambient Temperature: 32°F (0°C) to 120°F (49°C).
Humidity: Less than 85% relative humidity, continuous,
noncondensing.
Dimensions:
Control Panel:
12-1/2 in. x 12-1/2 in. x 3-1/8 in.
Keypad, LCD Two Line:
6-13/32 in. x 5-11/32 in. x 29/32 in.
Point Expansion Module:
6-1/2 in. x 4-5/16 in. x 1-13/32 in.
RF Point Expansion Module:
6-1/2 in. x 4-5/16 in. x 1-13/32 in.
RF Receiver
7-3/8 in. x 4-3/8 in. x 1-7/16 in. (with antenna 10-7/8 in.
high).
Transmitters:
See individual Ademco specification sheet with each
type transmitter.

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1
3
INSTALLATION
When Installing this Product...
1. Read these instructions carefully. Failure to follow them
can damage the product or cause a hazardous condition.
2. Check the ratings given in the instructions and marked
on the product to make sure the product is suitable for
the application.
3. Installer must be a trained, experienced service
technician.
4. After installation is complete, check out the product
operation as provided in these instructions.
Overview
This section provides a general overview of the system
(Fig. 1) and installation and hookup instructions for the
following equipment:
1. Control Panel:
a. Enclosure.
b. Circuit Board.
c. Transformer.
2. Point Expansion Module.
3. RF Expansion Module.
4. RF Receiver.
5. RF Transmitter.
6. Keypad.
Control Panel
The control panel performs the main functions of the system.
The following can be found inside the control panel
enclosure:
a. Control Panel Circuit Board.
b. Batteries.
Fig. 1. General overview of Honeywell System 7000.
BATTERY
TB1
J1
S1
CONTROL PANEL
HARDWIRE LOOPS
MODES
OPTIONS
OK
CANCEL
FIRE
POLICE
SPECIAL
123
456
789
0
POINT
EXPANSION
MODULE (PEM)
RF EXPANSION
MODULE (RFEM)
RF RECEIVER
KEYPAD
RF TRANSMITTERS
HBUS
HARDWIRE LOOPS
TELCO
LINES
PLUG-IN
TRANSFORMER
RJ31X
HORN/BELL
SMOKE
DETECTOR
M10907

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1 4
Location
Locate the control panel enclosure in an area that is dry and
not subject to temperature extremes. Prolonged exposure to
temperatures below 32°F (0°C) or above 120°F (50°C) can
adversely affect the battery and some system circuits.
The location selected should be well inside the secured area
and accessible for testing and reprogramming. Allow for
routing wire runs. Locate the control panel enclosure and any
accessory equipment, such as the PEM or RFEM in:
a. Interior closet.
b. Interior wall in an untravelled area.
NOTE: If a cement, brick or cinderblock wall is to
be used as a mounting location, use an
appropriately sized piece of 3/4 in. (19 mm)
plywood attached to the wall with wall
anchors as a base for the system.
Mounting (Fig. 2 and 3)
Determine what equipment will be mounted on the wall with
the control panel box, approximate location of each device,
and probable wiring runs. This can be a rough sketch, with
approximate dimensions of the devices (see Specifications).
Based on this information, cut the 3/4 in. (19 mm) plywood, if
necessary, to the appropriate dimensions and mount the
plywood on the selected wall using wall anchors or expansion
plugs.
IMPORTANT
For RF installations, mount the RF Receiver at least
25 feet away from any other sources of RF
interference, such as garage door opener receivers.
Avoid mirrors and reflecting surfaces such as metal
heating and cooling ducts. If insufficient RF strength
is noted, move the receiver.
Fig. 2. Mounting the control panel enclosure on drywall.
DRYWALL
SUPPLIED (4)
CIRCUIT
BOARD
CONTROL
BOX
DRYWALL
ANCHORS
(NOT SUPPLIED)
M10908

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1
5
Fig. 3. Mounting the control panel enclosure on plywood.
Place the empty control panel box in the correct location on
the plywood and mark the location of the mounting holes on
the plywood. If necessary, drill pilot holes at these locations.
Mount the control panel box using properly sized screw
anchors (not supplied) or other secure mounting techniques.
See Fig. 2 and 3.
CAUTION
Equipment Damage Hazard.
Static discharge can damage circuit board.
Follow ESD safety procedures when installing or
handling circuit board.
Circuit Board Installation
Mount the control panel printed circuit board in the metal
control panel box on the four standoffs and guides, using the
four screws and four lockwashers supplied.
Circuit Board Wiring
The control panel circuit board is the central wiring point for
most of the system. Connections are available for:
a. Loop wiring.
b. Smoke detector wiring.
c. Backup batteries.
d. External bell/horn.
e. Ac connections.
f. Earth ground.
g. Telephone interface connection.
h. HBus devices (keypad, PEM, RFEM, etc.).
Wiring instructions for each of these connections or devices
are provided in the appropriate section.
WARNING
Electrical Shock Hazard
Can cause serious injury or death.
Disconnect power before wiring
General
1. Protect all wiring entering the control panel box with
strain relief and bushings.
2. Use adhesive-backed cable tie mounts and cable ties
to secure the wiring to a convenient point inside the
control panel box.
3. Use two No. 6 screws to secure the control panel box
lid after wiring is completed.
See Fig. 4 for general information on circuit board wiring.
BRICK, CONCRETE OR
CINDER BLOCK WALL
3/4 IN. (19 MM)
PLYWOOD
CONTROL BOX
MOUNTING HARDWARE
FOR PLYWOOD
M10909

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1 6
Fig. 4. Control panel wiring, showing TB1 and general physical layout.
HOUSEHOLD FIRE AND BURGLARY WARNING SYSTEM.
U.L. HOME HEALTHCARE SIGNALING SYSTEM.
HOUSEHOLD BURGLARY U.L. GRADE A WHEN USED
WITH EXTERNAL AUDIBLE.
BEFORE INSTALLING, READ HONEYWELL SYSTEM 7000
INSTALLATION MANUAL, 69-1192 REV. 9/98.
BEFORE OPERATING, READ HONEYWELL SYSTEM 7000
OWNERS MANUAL.
THIS EQUIPMENT SHOULD BE INSTALLED IN
ACCORDANCE WITH CHAPTER 2 OF NFPA STANDARD 72.
NATIONAL FIRE PROTECTION ASSOCIATION,
BATTERYMARCH PARK, QUINCY, MA 02269
PRINTED INFORMATION DESCRIBING PROPER
INSTALLATION, OPERATION, TESTING, MAINTENANCE,
EVACUATION, PLANNING, AND REPAIR IS TO BE
PROVIDED WITH THIS EQUIPMENT.
THE SYSTEM IS U.L. LISTED FOR LIMITED ENERGY
INSTALLATIONS PER NEC ARTICLE 760.
USE ONLY U.L. RECOGNIZED LIMITED ENERGY CABLE.
TEST SYSTEM AT LEAST ONCE A WEEK WITH AC OFF.
SYSTEM SHOULD BE CHECKED BY A QUALIFIED
TECHNICIAN AT LEAST EVERY THREE YEARS.
STANDBY BATTERY/BATTERIES SHOULD BE REPLACED
EVERY FIVE YEARS.
DISCONNECT AC LINES AND TELEPHONE WIRES
BEFORE SERVICING.
SYSTEM 7000
HOME CONTROL SYSTEM
HOME AND BUILDING CONTROL
MINNEAPOLIS, MINNESOTA
WARNING:
OWNERS INSTRUCTION NOTICE NOT TO BE
REMOVED BY ANYONE EXCEPT OCCUPANT.
MAXIMUM OF 10 2-WIRE
SMOKE DETECTORS. REFER TO
INSTALLATION INSTRUCTIONS
69-1192 FOR A LIST OF
APPROVED DETECTORS.
SMOKE DETECTOR COMPATIBILITY
IDENTIFIER IS 7K8.
P8 MAY BE WIRED FOR 2-WIRE FIRE
OR 4-WIRE FIRE OR BURGLARY.
2-WIRE FIRE IS SHOWN. FOR
4-WIRE FIRE AND BURGLARY
WIRING, SEE INSTALLATION
INSTRUCTIONS.
+
HBUS-
1
+
HBUS+
2
+
COM
3
+
+13.8 VDC
4
+
P1
5
+
P2
6
+
COM
7
+
P3
8
+
P4
9
+
COM
10
+
P5
11
+
P6
12
+
COM
13
+
P7
14
+
P8-
15
+
P8+
16
+
AUX
17
+
HORN
18
+
COM
19
+
+13.8 VDC
20
+
AC IN
21
+
AC IN
22
STANDBY BATTERY
MINIMUM REQUIREMENTS: 12 VDC, 7 AH
REFERENCE PART NUMBER 32002215-001
REPLACE BATTERY EVERY 5YEARS.
SYSTEM SUPPLIES 4 TO 24 HR. EMERGENCY
STANDBY CAPACITY. 24 HOURS REQUIRED
FOR FIRE PROTECTION. SEE INSTALLATION
MANUAL 69-1192 REV 9/98 FOR EQUIPMENT
AND BATTERY CONFIGURATIONS.
WARNING: LEAVING THE POWER SWITCH
IN THE OFF POSITION RENDERS THE SYSTEM
7000 CONTROL PANEL INOPERABLE.
WARNING: FOR CONTINUED PROTECTION
AGAINST FIRE, REPLACE FUSE WITH SAME
TYPE AND RATING (AGA 2)
TELCO LINE COUPLER CORD TO RJ31X.
CONNECT PC PROGRAMMER HERE FOR LOCAL
PROGRAMMING.
J1
AC
S 1
CONNECT TO EARTH GROUND
GRN
YEL
BLK
RED
NC
NO
EOLR
EOLR
EOLR
HSP
PEM
RFEM
1
1
AUXILIARY OUTPUT,
PROGRAMMABLE
VOFF = 25V MAX (FLOAT)
VON = 1.1V MAX
ISINK = 100 mA
SMOKE DETECTOR
SMOKE DETECTOR
––
–
–
++
+
+
BELL / HORN
12 VDC,
1 AMP MAX.
5.1K 5% 1/4W
PLUG-IN TRANSFORMER
PART NO.: 32002143-001
INPUT 120 VAC, 60HZ
OUTPUT: 24 VAC, 50 VA
CLASS 2
DO NOT CONNECT AC
TRANSFORMER TO A
SWITCH CONTROLLED
OUTLET.
97-5790 REV.
3.3K 5% 1/4W
120Ω5% 1/4W
TYPICAL FOR
POINTS P1 TO P7
END-OF-LINE
RESISTOR MUST BE
AT END OF CONTACT.
END OF LINE RESISTOR
CONNECTED ACROSS THE
HBUS+ AND HBUS–
CONTACTS OF LAST (END)
DEVICE CONNECTED TO
THE HBUS CIRCUIT
TB 1
M10910

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1
7
Connect loop wiring but do not run wiring within 12 in. (305
mm) of house ac wiring.
IMPORTANT
Do not run any wires or cabling behind or across the
control panel printed circuit board.
Point Expansion Module (PEM) Installation
The PEM provides additional hardwire points for the
Honeywell 7000 System and can be used in place of, or in
conjunction with, the RF transmitters and receivers. The PEM
DRYWALL
OR PLYWOOD
NOT
SUPPLIED
PEM (COVER
REMOVED)
ANCHORS
M10912
MOUNTING SLOTS
ON BACK OF RFEM
can support normally open (NO) or normally closed (NC)
sensor contacts. The PEM has eight hardwire point
connections and two relay output connections.
Mount the PEM plastic box within 250 feet (76 meters) of the
control panel if using 22 AWG wire or 500 feet (152 meters) if
using 18 AWG wire.
Remove the PEM circuit board from the PEM plastic box (if
installed) and use the PEM plastic box to mark the mounting
screw locations on the wall or plywood. Use two screws (not
supplied) to mount the PEM plastic box. Insert the PEM
circuit board into the PEM plastic box. See Fig. 5.
Fig. 5. Installing the PEM plastic box.

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1 8
ON ON ON ON ON ON ON ON OFF OFF OFF
ON ON ON ON OFF OFF OFF OFF ON ON ON
ON ON OFF OFF ON ON OFF OFF ON ON OFF
ON OFF ON OFF OFF OFF ON OFF ON OFF ON
12 3 456 7891011
1
2
3
4
1
2
3
4
S1
TB1 TB2
OFF ON
S1
S1 SETS PEM ADDRESS #
S1 SHOWN SET FOR ADDRESS #1
MAXIMUM OF 11 PEMs ON A SYSTEM
PEM ADDRESS # 11
10
9
8
7
6
5
4
3
2
1
1234567891011
GND P1 P2 P3 P4 GND P5 P6 P7 P8– P8+
NO EOLR
NC
NO EOLR
NC
ALL EOLR =
3.3K 1/4W 5%
TYP WIRING: POINT 1-7 WIRING: POINT 8
GND
GND
+13.8 VDC
HBUS–
HBUS+
RELAY 1
TO
CONTROL
PANEL
GOLDEN VALLEY, MINN.
RELAY 2
NO
NC
C
NO
NC
C
BLK
RED
GRN
YEL
M10902
RELAY:
CURRENT DRAIN ≤40 mA
CONTACT RATING:
RESISTIVE
2A @ 30 VDC
0.4A @ 30 VAC
INDUCTIVE
1A @ 30 VDC
0.2A @ 30 VAC
LABEL 2480341 REV B
PEM
SYSTEM 7000
SEE INSTALLATION MANUAL
PEM Wiring
1. Use four-conductor AK4500A cable to connect the PEM
to other HBus devices.
2. Connect the PEM wires to the control panel according
to the wiring diagram with the unit. See Fig. 6.
Each PEM has a unique, four digit, address. Fig. 6 lists the
PEM address number and switch settings. The Honeywell
7000 System can support up to 11 PEM.
RFEM Installation
The RFEM provides additional rf protection points for the
Honeywell 7000 System. Only one RFEM can be used per
system.
Mount the RFEM plastic box within 250 feet (76 meters) of
the control panel if using 22 AWG wire or 500 feet (152
meters) if using 18 AWG wire.
Remove the RFEM circuit board from the RFEM plastic box
(if installed) and use the RFEM plastic box to mark the
mounting screw locations on the wall or plywood. Use two
screws to mount the RFEM plastic box. Insert the RFEM
circuit board into the RFEM plastic box. See Fig. 7.
Fig. 6. PEM wiring diagram.

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1
9
Fig. 7. Installing the RFEM.
DRYWALL
OR PLYWOOD
NOT
SUPPLIED
RFEM (COVER
REMOVED)
ANCHORS
M10911
MOUNTING SLOTS
ON BACK OF RFEM
RFEM Wiring
1. Use four-conductor AK4500A cable to connect the PEM
to other HBus devices.
2. Connect the RFEM wires to the control panel according
to the wiring diagram with the unit. See Fig. 8.
RF Receiver Installation
The RF Receiver receives messages from the RF
Transmitters, demodulates and transfers the data to the
RFEM for decoding. A maximum of two receivers can be
connected to an RFEM.
Perform the following steps:
1. Remove the cover from the RF Receiver (use a thin-
bladed screwdriver to release the cover).
2. Place the open receiver on the wall in the desired
location, leaving room for the two antennas.
3. Use a pencil or other marking device to mark the two
screw locations for the receiver.
4. Install the two screws (not supplied), leaving enough
room to hang the receiver on the screws.
5. Install the antennas in the slots as shown in Fig. 9. The
antennas go in the right-hand slot of each set.
6. Set the receiver switches as shown in Table 1.

HONEYWELL 7000 SOLID STATE ALARM SYSTEM
69-1192—1 10
Fig. 8. Connecting the RFEM to the RF Receiver.
ON - OFF
4
3
2
1
6
5
4
3
2
1
INTERFERENCE
INDICATOR
RF RECEIVER
RFEM
TB1
TO SYSTEM 7000
CONTROL PANEL
HBUS TERMINALS
GREEN
YELLOW
BLUE
RED
BLACK
GREEN
YELLOW
RED
BLACK
YELLOW
GREEN
RED
BLACK
YELLOW
GREEN
DATA IN
DATA OUT
+12V
(GND)
HBUS (+)
HBUS (–)
HBUS POWER DATA
PANEL
RF
ANTENNAE
R
G
M10903
Table 1. RF Receiver switch settings.
Receiver
Switch Position 1 2
4ONOff
3 OFF ON
2 OFF OFF
1----
RF Receiver Wiring
IMPORTANT
No two receivers can have the same address
settings. Only address 1 or 2 can be used.
CAUTION
Equipment Damage Hazard.
Incorrect connections can damage hardware.
Wire the RF Receiver according to Fig. 8.
Keypad Installation (Fig. 9)
The keypad is used by the homeowner to operate the
Honeywell 7000 System. The two-line display provides
information about what is happening and the locations of any
problems. The display will automatically prompt the user with
help instructions after eight seconds of inactivity.
Locate the keypad no further than 250 feet from the control
panel if using 22 AWG cable or 500 feet if using 18 AWG
cable. Do not route keypad wiring parallel to ac wiring or
within 12 in. of ac wiring.
NOTE: A maximum of 11 keypads can be installed
on one Honeywell 7000 System.The control
panel can supply power for up to four
keypads. Additional keypads must be
powered by an external 12V power source
with backup batteries.
A standard plastic base is provided. To mount the keypad:
1. Secure the base to the wall.
2. Attach the wires to the keypad.
3. Fasten the keypad to the base.
4. Attach the trim ring to the keypad.
Keypad Wiring
Honeywell 7000 System keypads are connected to each
other and to the control panel via the HBus. Follow these
wiring practices:
1. Use four-conductor AK4500A cable to connect the
keypad to other HBus devices.
2. Keep maximum distance for the data line from the
control panel to the farthest device under 3000 feet.
3. Keep the maximum distance from the power source to
the farthest keypad under 250 feet.
IMPORTANT
No more than four keypads can share the same
power wiring pair.
NOTE: Separate power sources are required when
the distance exceeds 250 feet. Use Altronix
Model AIL100 or ALARM SAF Model PS-FMC-
12/10-BFS/UL 3/4A power supplies when UL-
approved equipment is required.
4. Always use 120 ohm end-of-line resistors (provided
with keypad) to terminate the ends of the HBus line as
shown in Fig. 10 through 13.