Honeywell Galaxy Keyprox Technical specifications

Galaxy
Keyprox
Installation and Programming Instructions
Honeywell Security

Contents
Overview.......................................................................................................................................... 3
Compatibility ................................................................................................................................... 3
Mounting.......................................................................................................................................... 3
Wiring............................................................................................................................................... 3
Configuration .................................................................................................................................. 3
Volume Control ............................................................................................................................... 4
Keypad Programming .................................................................................................................... 4
MAX Programming ......................................................................................................................... 4
Card Programming ......................................................................................................................... 4
Card Self-Learn Procedure ............................................................................................................ 4
Operation......................................................................................................................................... 5
Dual Focus ................................................................................................................................... 5
Card Reader Buzzer Indications .................................................................................................. 5
Door Control Programming ........................................................................................................... 6
Specifications ................................................................................................................................. 7
EN50131 Compliance ..................................................................................................................... 7
Declaration of Conformity ............................................................................................................. 8
2

Overview
The Galaxy Keyprox is a standard Galaxy MK7 keypad and a proximity card reader, combined
into one housing. This allows dual function setting/unsetting ability from the one station without
the need for a separate card reader. It is primarily intended for use in situations where a PIN
and/or card are needed to set and unset the intruder alarm system. It is not intended to be used
for door control as it does not contain a door strike relay. However, limited door functions can
be programmed using Links programming in the Galaxy control panels.
Compatibility
The Galaxy Keyprox is intended for use with the Galaxy 8, 18, 60, 128, 500, 504 and 512
panels. The panels must be fitted with software version 1.18 or later. The Keyprox is also used
with the Galaxy 2 and 3 Series panels.
Most standard ASK cards with 26 and 34 Bit formats can be read by the Keyprox. Proprietary
card type may not be read properly by the Keyprox.
* Note that some versions of the keypad may have the HID functionality enabled. Keyprox
units with the -H suffix have the HID functionality.
MAX cards or tags can be read by the Keyprox. However if MAX or MicroMAX readers are
also used on the system, then the cards will need to be programmed on to two separate users, as
they are seen in a different way by the MAX type readers and the Keyprox.
Mounting
The Keyprox should be mounted on a flat vertical surface in a convenient location. Separate the
back plate from the rest of the keypad by gently pushing on the two locking clips on the base of
the Keyprox with a screwdriver. Place the back plate on the wall at the desired location and
mark the position of the screw holes. Remove the plate then drill the holes as required. The back
plate can then be screwed to the wall while running the cable connection through the available
opening. Once the back plate has been secured to the wall, the rest of the Keyprox can be
clipped in place by locating the top lugs first, then pushing the lower clips home, gently but
firmly. If required, the supplied prox-card sticker can be applied to the lower right corner of the
Keyprox front or door for identification.
Wiring
The Keyprox must be wired to the RS485 data bus on the Galaxy panel, maintaining the parallel
daisy chain wiring configuration. Only 4 connections are required, +12V, 0V, A and B data. If
the Keyprox is the last module on the A B RS485 data bus, then a 680 ohm end-of-line resistor
must be fitted across the A and B terminals.
Configuration
The following set-up is required before the Keyprox can be used with the Galaxy system:
Before powering the Keyprox, set the address using the rotary switch on the PCB. This sets the
address for both the keypad and card reader parts of the Keyprox, so the address must be chosen
carefully. The address must be a valid one for both a keypad and a MAX reader on that line, as
shown in the table. Also, the address must not clash with any other keypad, MicroMAX reader,
RF RIO MAX address or Keyprox connected to the same line.
3

Panel 8 18 60 128 500 504, 512 G2 G3
Line 1 0,1 0,1,2 0,1,2,3 0,1,2 0,1,2 0,1,2 0,1,2,3 0,1,2
Line 2 - - - 0,1,2,3 0,1,2,3 0 - 6 - 0 - 6
Line 3 - - - - 0,1,2,3 0 - 6 - 0 - 6
Line 4 - - - - 0,1,2,3 0 - 6 - 0 - 6
After the unit is powered up, MAX mode on the Galaxy panel must be enabled (if this has not
already been done). This is done in engineers mode, menu 63.2.1.
NOTE: MAX mode is not applicable to Galaxy 2 Series panels.
If the keypad and MicroMAX sections of the Keyprox have not already configured themselves
onto the system, bring the panel out of engineers mode to do so. After exiting engineer mode,
the keypad will indicate ‘1 MOD ADDED’ and show the address of the MAX.
Volume Control
The Keyprox part number CP038 has a volume control pot marked VOL at the bottom right-
hand corner of the pcb. To adjust the volume open up the keypad cover and adjust the pot
(+ or -).
Keypad Programming
The keypad side of the Keyprox requires no programming for most installations. If required, the
parameters for the keypad can be altered in programming menu 58.
MAX Programming
The parameters for the MAX side of the Keyprox can be altered in programming menu 63.2.3.
NOTE: MAX programming is not applicable to Galaxy 2 Series panels.
Card Programming
In order for the card reader to operate, the unique serial number programmed into each card to
be used must be programmed to a separate user on the Galaxy panel. This can be simplified by
using the self-learn procedure described below. The MAX card-held function also needs to be
programmed here, to allow the card to set and unset the system. Refer to the relevant sections in
the Galaxy Panel user or installation manuals for full details. (menu 42 - codes.)
Card Self-Learn Procedure
Many proximity cards have no serial numbers printed on them, and some cards, such as MAX
tags, have encrypted numbers. However, the card number must be programmed into the Galaxy
panel to allow the card to work. To cater for this programming process, a card self-learn
procedure has been included in the Keyprox. (This must be used for MAX tags)
NOTE: The card self-learn procedure should only be used whilst the Keyprox is in the user
menu for entering the MAX card number and the panel is waiting for the actual card number to
be entered. Use of the self-learn at other times will result in random operations.
4

Procedure
1. Use the Keyprox to enter menu option 42.1. Select the user to which the card is to be
assigned. Within the user menu, select option 7=MAX Number.
2. Delete all the digits of the existing number using the B< button.
3. Place the keypad in the self-learn mode by holding the A button down and pressing the 1
button simultaneously. The keypad will give a double beep to indicate entry into the self-
learn mode.
4. Within 5 seconds of the double beep, present the new card at the Keyprox.
5. The card number will appear on the keypad display, followed by a single beep.
6. Press ENT to save the card number.
7. To allow the card to set and unset the system via the Keyprox, option 8=MAX Function
(Card-Held) must be programmed with a setting option (e.g. 12=Timed Set).
8. To enter more cards, repeat the procedure for other users.
NOTE: The self-learn mode will time out after 5 seconds if no card is presented.
During the self-learn mode operation, the keypad buttons will not function.
Operation
The Keyprox will behave as two separate modules. The keypad section will function as a
standard Galaxy Keypad, for setting/unsetting, programming and general operation.
The proximity card reader section operates in a similar way to a Galaxy MicroMAX reader.
Swiping a card in front of the read head in the lower right hand corner of the keypad will be
seen as a valid card read by the panel. This can be utilised, if required, by using Links on the
Galaxy Panel. To perform the card-held function assigned to card user, the card must be held in
front of the read head for at least 3 seconds. A long beep will be heard from the keypad buzzer
to indicate that the card is valid. A long beep will be heard 3 seconds later and the card-held
function will be performed.
Dual Focus
Dual Focus means that the PIN and the Card belonging to the same user must be used together
to access the system. This is typically used as a secure method of setting and unsetting the
system. To achieve this, assign a # to the PIN of the user and to the MAX number. Assign an
appropriate MAX function, for example, 12=Timed set. To set the system now, a user would
have to enter their PIN, then hold the card in front of the reader for 3 seconds to begin setting
the system. To unset, simply enter the PIN then briefly swipe the card in front of the reader.
Card Reader Buzzer Indications
Event Buzzer indication
Card number read by reader Short beep
Card number validated Long Beep
Card Held function activated Double Beep
5

Door Control Programming
Door control functionality can be achieved by setting up zones, outputs and links on the
Galaxy panel as shown in the example below.
Zone 1011 is programmed as a Security zone.
Zone 1012 is programmed as a Link zone.
Output 1011 is programmed as Link-A type, mode=pulse 5 Sec.
Output 1021 is programmed as Link-B (door open time out), pulse 15 Sec.
Keyprox is on address 00 (MAX 10)
Program the following links:
1. Source MAX 10 Destination Link-A
2. Source MAX 10 Destination Link-B
3. Source #1012 Destination Zone 1011
4. Source Zone 1012 Destination Link-A
5. Source Zone 1012 Destination Link-B
This will program the door to unlock for 5 seconds and allow it to stay open for 15 seconds from
whenever a valid card is swiped at the Keyprox. Zone 1012 is programmed as an Egress button,
which will open the door in the same way as a valid card swipe.
If the door is forced, a standard zone alarm will occur. It will not be recorded as a MAX alarm
in the Access log (menu 25).
6

Specifications
Dimensions 148 x 90 x 31mm
Weight 225g
Operating Temp -10oC to 40oC*
Proximity Reader 125kHz, Inductive
Read range 15mm nominal, dependent on card type.
Current Draw Typical, 90mA
Maximum, 140mA
*NOTE: The display may not operate correctly at temperatures below 0oC. However the
Keyprox will still continue to operate on the system. When the temperature rises above 0oC
again, the display will return to normal.
EN50131 Compliance
This product is suitable for use in systems designed to comply with PD6662:2004 and
prEN50131-1:2004
Security Grade - 3
Environmental Class – II
This product is suitable for use in systems designed to comply with EN50131-1:1997
Security Grade - 2
Environmental Class – II
7

Declaration of Conformity
Declaration of Conformity
Hereby, Honeywell Security declares that the Galaxy Keyprox card reader and
keypad is in compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.
This device is intended for use in the following countries:
Austria Belgium Denmark Finland
France Germany Iceland Ireland
Italy Luxembourg Netherlands Norway
Portugal Spain Sweden Switzerland
United Kingdom
Honeywell Security
2 Redwood Crescent
Peel Park Campus
East Kilbride
G74 5PA
II1-0029 Rev 1.6 © Copyright Honeywell Security
8